Re: [debian-knoppix] Set CONFIG_SCSI_MULTI_LUN to Y
At 03:14 PM 7/3/03 , Klaus Knopper wrote:
On Thu, Jul 03, 2003 at 01:55:24PM -0400, Steve wrote:
> Could you elaborate on that? I may be a bit confused. Is the 0 0 0 1 not
> chosing LUN 1? Thanks.
It's chosing LUN1 for Controller 0, Channel 0, SCSI ID 0.
Are you sure that your device was given this exact SCSI path by hotplug?
Did you check with dmesg?
This is what I get with dmesg with Knoppix (unrelated items snipped)
After that is my gentoo dmesg, which has CONFIG_SCSI_MULTI_LUN to Y in the
kernel. Is it something in hotplug that is not picking it up, do I need to
forget about accessing the second card on my reader? Thanks for the help.
Linux version 2.4.20-xfs (root@Knoppix) (gcc version 2.95.4 20011002
(Debian prerelease)) #1 SMP Mit Mär 26 15:37:36 CET 2003
<snipped>
Kernel command line: ramdisk_size=100000 init=/etc/init lang=us
apm=power-off hda=scsi hdb=scsi hdc=scsi hdd=scsi hde=scsi hdf=scsi
hdg=scsi hdh=scsi vga=791 initrd=miniroot.gz nomce quiet BOOT_IMAGE=knoppix
BOOT_IMAGE=vmlinuz 2 alsa wheelmouse lang=us
ide_setup: hda=scsi
ide_setup: hdb=scsi
ide_setup: hdc=scsi
ide_setup: hdd=scsi
ide_setup: hde=scsi
ide_setup: hdf=scsi
ide_setup: hdg=scsi
ide_setup: hdh=scsi
<snipped>
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: SONY Model: CD-RW CRX175E2 Rev: S002
Type: CD-ROM ANSI SCSI revision: 02
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
<snipped>
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 15:50:01 Mar 26 2003
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 9 for device 00:07.2
usb-uhci.c: USB UHCI at I/O 0x1800, IRQ 9
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usbdevfs: remount parameter error
hub.c: new USB device 00:07.2-1, assigned address 2
usb.c: USB device 2 (vend/prod 0x781/0x810) is not claimed by any active
driver.
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
scsi1 : SCSI emulation for USB Mass Storage devices
Vendor: SanDisk Model: ImageMate CF-SM Rev: 0100
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi removable disk sda at scsi1, channel 0, id 0, lun 0
sda : READ CAPACITY failed.
sda : status = 1, message = 00, host = 0, driver = 08
Current sd00:00: sense key Not Ready
Additional sense indicates Medium not present
sda : block size assumed to be 512 bytes, disk size 1GB.
sda: I/O error: dev 08:00, sector 0
I/O error: dev 08:00, sector 0
ldm_validate_partition_table(): Disk read failed.
I/O error: dev 08:00, sector 0
unable to read partition table
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 2
USB Mass Storage support registered.
<snipped>
FAT: bogus logical sector size 0
VFS: Can't find a valid FAT filesystem on dev 03:08.
FAT: bogus logical sector size 0
VFS: Can't find a valid FAT filesystem on dev 03:08.
NTFS driver v1.1.22 [Flags: R/W MODULE]
Journalled Block Device driver loaded
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
sda : READ CAPACITY failed.
sda : status = 1, message = 00, host = 0, driver = 08
Current sd00:00: sense key Not Ready
Additional sense indicates Medium not present
sda : block size assumed to be 512 bytes, disk size 1GB.
sda: Write Protect is off
sda: I/O error: dev 08:00, sector 0
I/O error: dev 08:00, sector 0
ldm_validate_partition_table(): Disk read failed.
I/O error: dev 08:00, sector 0
unable to read partition table
I/O error: dev 08:00, sector 0
Gentoo dmesg:
Linux version 2.4.20-ck6 (root@Gretchen) (gcc version 3.2.2) #1 Fri Apr 18
16:52:21 EDT 2003
<snipped>
Kernel command line: BOOT_IMAGE=LATEST ro root=30a hdc=ide-scsi
ide_setup: hdc=ide-scsi
<snipped>
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: SONY Model: CD-RW CRX175E2 Rev: S002
Type: CD-ROM ANSI SCSI revision: 02
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
sr0: mmc-3 profile capable, current profile: 0h
<snipped>
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
uhci.c: USB Universal Host Controller Interface driver v1.1
PCI: Found IRQ 9 for device 00:07.2
uhci.c: USB UHCI at I/O 0x1800, IRQ 9
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
hid-core.c: USB HID support drivers
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
<snipped>
hub.c: new USB device 00:07.2-1, assigned address 2
scsi1 : SCSI emulation for USB Mass Storage devices
Vendor: SanDisk Model: ImageMate CF-SM Rev: 0100
Type: Direct-Access ANSI SCSI revision: 02
Vendor: SanDisk Model: ImageMate CF-SM Rev: 0100
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi removable disk sda at scsi1, channel 0, id 0, lun 0
Attached scsi removable disk sdb at scsi1, channel 0, id 0, lun 1
sda : READ CAPACITY failed.
sda : status = 1, message = 00, host = 0, driver = 08
Current sd00:00: sns = 70 2
ASC=3a ASCQ= 0
Raw sense data:0x70 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00
0x3a 0x00 0x00 0x00 0x00 0x00
sda : block size assumed to be 512 bytes, disk size 1GB.
/dev/scsi/host1/bus0/target0/lun0: I/O error: dev 08:00, sector 0
I/O error: dev 08:00, sector 0
unable to read partition table
sdb : READ CAPACITY failed.
sdb : status = 1, message = 00, host = 0, driver = 08
Current sd00:00: sns = 70 2
ASC=3a ASCQ= 0
Raw sense data:0x70 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00
0x3a 0x00 0x00 0x00 0x00 0x00
sdb : block size assumed to be 512 bytes, disk size 1GB.
/dev/scsi/host1/bus0/target0/lun1: I/O error: dev 08:10, sector 0
I/O error: dev 08:10, sector 0
unable to read partition table
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 2
VFS: Disk change detected on device 08:00
sda : READ CAPACITY failed.
sda : status = 1, message = 00, host = 0, driver = 08
Current sd00:00: sns = 70 2
ASC=3a ASCQ= 0
Raw sense data:0x70 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00
0x3a 0x00 0x00 0x00 0x00 0x00
sda : block size assumed to be 512 bytes, disk size 1GB.
sda: Write Protect is off
/dev/scsi/host1/bus0/target0/lun0: I/O error: dev 08:00, sector 0
I/O error: dev 08:00, sector 0
VFS: Disk change detected on device 08:10
sdb : READ CAPACITY failed.
sdb : status = 1, message = 00, host = 0, driver = 08
Current sd00:00: sns = 70 2
ASC=3a ASCQ= 0
Raw sense data:0x70 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00
0x3a 0x00 0x00 0x00 0x00 0x00
sdb : block size assumed to be 512 bytes, disk size 1GB.
sdb: Write Protect is off
/dev/scsi/host1/bus0/target0/lun1: I/O error: dev 08:10, sector 0
I/O error: dev 08:10, sector 0
_______________________________________________
debian-knoppix mailing list
debian-knoppix@linuxtag.org
http://mailman.linuxtag.org/mailman/listinfo/debian-knoppix
Reply to: