Bug#542902: linux-image-2.6.26-2-686: local e1000e clobbered in update
Package: linux-image-2.6.26-2-686
Version: 2.6.26-17lenny2
Severity: normal
Hi,
With this package as the only kernel installed, and hence the running kernel, an upgrade replaces the locally built driver for the e1000e module.
In my case, I have compiled the module locally as the packaged version (0.3.3 i think) doesn't support the option of disabling the MSI interupts and hence the system panics. I have compiled and installed the latest version from the Intel website (version 1.0.2.5) which does support this option. Obviously, this replaces the packaged file. The replacement file is a different size, date/time stamp and a different module version.
By replacing the locally built module a reboot causes a panic.
Shouldn't the package respect local changes such as this and not overwrite the changed module?
Regards,
Tim
-- Package-specific info:
** Version:
Linux version 2.6.26-2-686 (Debian 2.6.26-17lenny2) (dannf@debian.org) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 SMP Fri Aug 14 01:27:18 UTC 2009
** Command line:
root=/dev/md0 ro acpi=on console=ttyS0,38400
** Not tainted
** Kernel log:
[ 14.921551] md: md4 stopped.
[ 15.196354] md: bind<sdd1>
[ 15.204721] md: bind<sdc1>
[ 15.212950] usb 1-2: configuration #1 chosen from 1 choice
[ 15.247511] raid1: raid set md4 active with 2 out of 2 mirrors
[ 15.680012] kjournald starting. Commit interval 5 seconds
[ 15.700255] EXT3-fs: mounted filesystem with ordered data mode.
[ 16.831534] hiddev96hidraw0: USB HID v1.10 Device [American Power Conversion Back-UPS RS 500 FW:30.j5.I USB FW:j5] on usb-0000:00:10.0-2
[ 16.870394] usb 1-2: New USB device found, idVendor=051d, idProduct=0002
[ 16.890427] usb 1-2: New USB device strings: Mfr=3, Product=1, SerialNumber=2
[ 16.911759] usb 1-2: Product: Back-UPS RS 500 FW:30.j5.I USB FW:j5
[ 16.930240] usb 1-2: Manufacturer: American Power Conversion
[ 16.947162] usb 1-2: SerialNumber: BB0522001803
[ 17.196055] usb 2-1: new full speed USB device using uhci_hcd and address 2
[ 17.362962] usb 2-1: not running at top speed; connect to a high speed hub
[ 17.421056] usb 2-1: configuration #1 chosen from 1 choice
[ 17.441668] usb 2-1: New USB device found, idVendor=04b8, idProduct=0007
[ 17.461799] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 17.483160] usb 2-1: Product: USB2.0 Printer
[ 17.495921] usb 2-1: Manufacturer: EPSON
[ 17.507654] usb 2-1: SerialNumber: L53010309051407480
[ 17.582344] udevd version 125 started
[ 17.914036] usblp0: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x04B8 pid 0x0007
[ 17.939357] usbcore: registered new interface driver usblp
[ 19.239414] Linux agpgart interface v0.103
[ 19.260012] agpgart: Detected VIA VT3314 chipset
[ 19.284001] agpgart: AGP aperture is 128M @ 0xf0000000
[ 19.376226] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 19.489823] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 19.549868] input: Power Button (FF) as /class/input/input0
[ 19.614319] ACPI: Power Button (FF) [PWRF]
[ 19.626771] input: Sleep Button (CM) as /class/input/input1
[ 19.849287] ACPI: Sleep Button (CM) [SLPB]
[ 19.861698] input: Power Button (CM) as /class/input/input2
[ 20.153783] ACPI: Power Button (CM) [PWRB]
[ 21.091473] input: PC Speaker as /class/input/input3
[ 21.198340] Error: Driver 'pcspkr' is already registered, aborting...
[ 21.246645] b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded successfully
[ 21.278547] flexcop-pci: will use the HW PID filter.
[ 21.293419] flexcop-pci: card revision 2
[ 21.305166] ACPI: PCI Interrupt 0000:05:08.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 21.419065] e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2.5-NAPI
[ 21.437961] e1000e: Copyright(c) 1999 - 2009 Intel Corporation.
[ 21.512193] DVB: registering new adapter (FlexCop Digital TV device)
[ 21.536016] b2c2-flexcop: MAC address = 00:d0:d7:0d:d6:3a
[ 21.552244] b2c2-flexcop: i2c master_xfer failed
[ 21.565399] b2c2-flexcop: i2c master_xfer failed
[ 21.579204] CX24123: cx24123_i2c_readreg: reg=0x0 (error=-121)
[ 21.596638] CX24123: wrong demod revision: 87
[ 21.735111] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
[ 21.831729] b2c2-flexcop: i2c master_xfer failed
[ 22.048190] b2c2-flexcop: i2c master_xfer failed
[ 22.097489] b2c2-flexcop: found 'Zarlink MT352 DVB-T' .
[ 22.114223] DVB: registering frontend 0 (Zarlink MT352 DVB-T)...
[ 22.134281] b2c2-flexcop: initialization of 'Air2PC/AirStar 2 DVB-T' at the 'PCI' bus controlled by a 'FlexCopIIb' complete
[ 22.167991] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 22.190224] PCI: Disallowing DAC for device 0000:03:00.0
[ 22.206217] PCI: Setting latency timer of device 0000:03:00.0 to 64
[ 22.206388] 0000:03:00.0: : Failed to initialize MSI interrupts. Falling back to legacy interrupts.
[ 22.236269] flexcop-pci: will use the HW PID filter.
[ 22.251134] flexcop-pci: card revision 2
[ 22.262885] ACPI: PCI Interrupt 0000:05:09.0[A] -> GSI 18 (level, low) -> IRQ 18
[ 22.301384] DVB: registering new adapter (FlexCop Digital TV device)
[ 22.323997] b2c2-flexcop: MAC address = 00:d0:d7:0b:84:bc
[ 22.340245] b2c2-flexcop: i2c master_xfer failed
[ 22.353251] b2c2-flexcop: i2c master_xfer failed
[ 22.367089] CX24123: cx24123_i2c_readreg: reg=0x0 (error=-121)
[ 22.384529] CX24123: wrong demod revision: 87
[ 22.397791] b2c2-flexcop: i2c master_xfer failed
[ 22.546849] 0000:03:00.0: eth1: (PCI Express:2.5GB/s:Width x1) 00:1b:21:28:80:68
[ 22.569024] 0000:03:00.0: eth1: Intel(R) PRO/1000 Network Connection
[ 22.589099] 0000:03:00.0: eth1: MAC: 2, PHY: 4, PBA No: d50854-003
[ 22.612922] b2c2-flexcop: i2c master_xfer failed
[ 22.626216] b2c2-flexcop: found 'Zarlink MT352 DVB-T' .
[ 22.641986] DVB: registering frontend 1 (Zarlink MT352 DVB-T)...
[ 22.660023] b2c2-flexcop: initialization of 'Air2PC/AirStar 2 DVB-T' at the 'PCI' bus controlled by a 'FlexCopIIb' complete
[ 23.304711] Adding 78148152k swap on /dev/hda1. Priority:-1 extents:1 across:78148152k
[ 23.718352] EXT3 FS on md0, internal journal
[ 25.508006] kjournald starting. Commit interval 5 seconds
[ 25.554666] EXT3 FS on md1, internal journal
[ 25.565875] EXT3-fs: mounted filesystem with ordered data mode.
[ 25.612007] kjournald starting. Commit interval 5 seconds
[ 25.654053] EXT3 FS on md2, internal journal
[ 25.667090] EXT3-fs: mounted filesystem with ordered data mode.
[ 25.854397] JFS: nTxBlock = 8192, nTxLock = 65536
[ 28.120876] NET: Registered protocol family 10
[ 28.134831] lo: Disabled Privacy Extensions
[ 28.360676] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 31.232953] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[ 31.255641] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 35.425283] RPC: Registered udp transport module.
[ 35.439380] RPC: Registered tcp transport module.
[ 35.584145] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 41.608021] eth1: no IPv6 routers present
[ 48.925001] lp0: using parport0 (interrupt-driven).
[ 48.979900] ppdev: user-space parallel port driver
[ 56.281432] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 56.312765] NFSD: starting 90-second grace period
[ 59.461908] warning: `ntpd' uses 32-bit capabilities (legacy support in use)
[ 65.796189] device eth1 entered promiscuous mode
** Loaded modules:
Module Size Used by
ppdev 6500 0
lp 8164 0
nfsd 186672 17
auth_rpcgss 33952 1 nfsd
exportfs 3904 1 nfsd
nfs 214024 0
lockd 54568 2 nfsd,nfs
nfs_acl 2912 2 nfsd,nfs
sunrpc 162528 13 nfsd,auth_rpcgss,nfs,lockd,nfs_acl
ipv6 235364 64
jfs 148812 2
nls_base 6820 1 jfs
mt352 5572 2
evdev 8000 3
stv0299 8680 0
parport_pc 22500 1
parport 30988 3 ppdev,lp,parport_pc
e1000e 125804 0
b2c2_flexcop_pci 5720 0
b2c2_flexcop 24812 1 b2c2_flexcop_pci
dvb_core 66528 2 stv0299,b2c2_flexcop
firmware_class 6816 1 b2c2_flexcop
cx24123 12168 1 b2c2_flexcop
s5h1420 10052 1 b2c2_flexcop
snd_pcsp 8576 0
snd_pcm 62596 1 snd_pcsp
snd_timer 17800 1 snd_pcm
snd 45604 3 snd_pcsp,snd_pcm,snd_timer
soundcore 6368 1 snd
snd_page_alloc 7816 1 snd_pcm
serio_raw 4740 0
psmouse 32336 0
i2c_viapro 6836 0
i2c_core 19828 6 mt352,stv0299,b2c2_flexcop,cx24123,s5h1420,i2c_viapro
button 6096 0
shpchp 25528 0
pci_hotplug 23460 1 shpchp
via_agp 7744 1
agpgart 28776 1 via_agp
usblp 10592 0
ext3 105512 3
jbd 39444 1 ext3
mbcache 7108 1 ext3
raid1 18016 5
md_mod 67068 6 raid1
floppy 47748 0
ehci_hcd 28396 0
ide_cd_mod 27652 0
ide_disk 10496 2
thermal 15228 0
processor 32544 1 thermal
fan 4164 0
thermal_sys 10856 3 thermal,processor,fan
uhci_hcd 18672 0
ahci 23596 10
libata 140416 1 ahci
dock 8304 1 libata
sd_mod 22200 14
sr_mod 13316 0
cdrom 30176 2 ide_cd_mod,sr_mod
sg 26964 0
usbhid 35904 2
hid 33184 1 usbhid
ff_memless 4392 1 usbhid
usbserial 26472 0
usbcore 118224 8 usblp,ehci_hcd,uhci_hcd,usbhid,usbserial
aic7xxx 117592 0
scsi_transport_spi 19840 1 aic7xxx
scsi_mod 129324 6 libata,sd_mod,sr_mod,sg,aic7xxx,scsi_transport_spi
via_rhine 18664 0
mii 4896 1 via_rhine
via82cxxx 6948 0 [permanent]
ide_core 96136 3 ide_cd_mod,ide_disk,via82cxxx
** PCI devices:
00:00.0 Host bridge [0600]: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge [1106:0314]
Subsystem: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge [1106:0314]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 8
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
Capabilities: <access denied>
Kernel driver in use: agpgart-via
Kernel modules: via-agp
00:00.1 Host bridge [0600]: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge [1106:1314]
Subsystem: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge [1106:1314]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:00.2 Host bridge [0600]: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge [1106:2314]
Subsystem: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge [1106:2314]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:00.3 Host bridge [0600]: VIA Technologies, Inc. PT890 Host Bridge [1106:3208]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Kernel modules: via-agp
00:00.4 Host bridge [0600]: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge [1106:4314]
Subsystem: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge [1106:4314]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:00.7 Host bridge [0600]: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge [1106:7314]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:01.0 PCI bridge [0604]: VIA Technologies, Inc. VT8237/VX700 PCI Bridge [1106:b198] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: fc800000-fe8fffff
Prefetchable memory behind bridge: d7f00000-dfefffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR+ <PERR+
BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel modules: shpchp
00:0f.0 IDE interface [0101]: VIA Technologies, Inc. VT8251 AHCI/SATA 4-Port Controller [1106:3349] (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: VIA Technologies, Inc. VT8251 AHCI/SATA 4-Port Controller [1106:3349]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin B routed to IRQ 221
Region 0: I/O ports at ec00 [size=8]
Region 1: I/O ports at e880 [size=4]
Region 2: I/O ports at e800 [size=8]
Region 3: I/O ports at e480 [size=4]
Region 4: I/O ports at e400 [size=16]
Region 5: Memory at febffc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ahci
Kernel modules: ahci
00:0f.1 IDE interface [0101]: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE [1106:0571] (rev 07) (prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc. VT82C586/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE [1106:0571]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=1]
Region 4: I/O ports at fc00 [size=16]
Capabilities: <access denied>
Kernel driver in use: VIA_IDE
Kernel modules: via82cxxx
00:10.0 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 90) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at e080 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:10.1 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 90) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin C routed to IRQ 22
Region 4: I/O ports at e000 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:10.2 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 90) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at dc00 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:10.3 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 90) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin D routed to IRQ 23
Region 4: I/O ports at d880 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:10.4 USB Controller [0c03]: VIA Technologies, Inc. USB 2.0 [1106:3104] (rev 90) (prog-if 20 [EHCI])
Subsystem: VIA Technologies, Inc. USB 2.0 [1106:3104]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 128 bytes
Interrupt: pin C routed to IRQ 22
Region 0: Memory at febff800 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:11.0 ISA bridge [0601]: VIA Technologies, Inc. VT8251 PCI to ISA Bridge [1106:3287]
Subsystem: VIA Technologies, Inc. VT8251 PCI to ISA Bridge [1106:3287]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
Kernel modules: i2c-viapro
00:11.7 Host bridge [0600]: VIA Technologies, Inc. VT8251 Ultra VLINK Controller [1106:287e]
Subsystem: VIA Technologies, Inc. VT8251 Ultra VLINK Controller [1106:287e]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 128
Capabilities: <access denied>
00:12.0 Ethernet controller [0200]: VIA Technologies, Inc. VT6102 [Rhine-II] [1106:3065] (rev 7c)
Subsystem: ASUSTeK Computer Inc. Device [1043:80a7]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (750ns min, 2000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 23
Region 0: I/O ports at d400 [size=256]
Region 1: Memory at febff400 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: via-rhine
Kernel modules: via-rhine
00:13.0 PCI bridge [0604]: VIA Technologies, Inc. VT8251 Host Bridge [1106:287b] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=02, subordinate=04, sec-latency=0
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: fe900000-fe9fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Kernel modules: shpchp
00:13.1 PCI bridge [0604]: VIA Technologies, Inc. VT8251 PCI to PCI Bridge [1106:287a] (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fea00000-feafffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
01:00.0 VGA compatible controller [0300]: VIA Technologies, Inc. CN700/P4M800 Pro/P4M800 CE/VN800 [S3 UniChrome Pro] [1106:3344] (rev 01) (prog-if 00 [VGA controller])
Subsystem: ASUSTeK Computer Inc. Device [1043:3344]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (500ns min)
Interrupt: pin A routed to IRQ 0
Region 0: Memory at d8000000 (32-bit, prefetchable) [size=64M]
Region 1: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Expansion ROM at fe8f0000 [disabled] [size=64K]
Capabilities: <access denied>
02:00.0 PCI bridge [0604]: VIA Technologies, Inc. VT8251 PCIE Root Port [1106:287c] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=02, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: fe900000-fe9fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
02:00.1 PCI bridge [0604]: VIA Technologies, Inc. VT8251 PCIE Root Port [1106:287d] (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=02, secondary=04, subordinate=04, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
03:00.0 Ethernet controller [0200]: Intel Corporation 82572EI Gigabit Ethernet Controller (Copper) [8086:10b9] (rev 06)
Subsystem: Intel Corporation PRO/1000 PT Desktop Adapter [8086:1083]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fe9e0000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at fe9c0000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at bc00 [size=32]
Expansion ROM at fe9a0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: e1000e
Kernel modules: e1000e
05:08.0 Network controller [0280]: Techsan Electronics Co Ltd B2C2 FlexCopII DVB chip / Technisat SkyStar2 DVB card [13d0:2103] (rev 02)
Subsystem: Techsan Electronics Co Ltd B2C2 FlexCopII DVB chip / Technisat SkyStar2 DVB card [13d0:2103]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin A routed to IRQ 17
Region 0: Memory at feaf0000 (32-bit, non-prefetchable) [size=64K]
Region 1: I/O ports at cc00 [size=32]
Kernel driver in use: b2c2_flexcop_pci
Kernel modules: b2c2-flexcop-pci
05:09.0 Network controller [0280]: Techsan Electronics Co Ltd B2C2 FlexCopII DVB chip / Technisat SkyStar2 DVB card [13d0:2103] (rev 02)
Subsystem: Techsan Electronics Co Ltd B2C2 FlexCopII DVB chip / Technisat SkyStar2 DVB card [13d0:2103]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin A routed to IRQ 18
Region 0: Memory at feae0000 (32-bit, non-prefetchable) [size=64K]
Region 1: I/O ports at c880 [size=32]
Kernel driver in use: b2c2_flexcop_pci
Kernel modules: b2c2-flexcop-pci
-- System Information:
Debian Release: 5.0.2
APT prefers stable
APT policy: (500, 'stable')
Architecture: i386 (i686)
Kernel: Linux 2.6.26-2-686 (SMP w/1 CPU core)
Locale: LANG=en_AU, LC_CTYPE=en_AU (charmap=ISO-8859-1)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.26-2-686 depends on:
ii debconf [debconf-2.0] 1.5.24 Debian configuration management sy
ii initramfs-tools [linux-initra 0.92o tools for generating an initramfs
ii module-init-tools 3.4-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.26-2-686 recommends:
ii libc6-i686 2.7-18 GNU C Library: Shared libraries [i
Versions of packages linux-image-2.6.26-2-686 suggests:
ii grub 0.97-47lenny2 GRand Unified Bootloader (Legacy v
ii linux-doc-2.6.26 2.6.26-17lenny2 Linux kernel specific documentatio
-- debconf information:
linux-image-2.6.26-2-686/postinst/bootloader-error-2.6.26-2-686:
linux-image-2.6.26-2-686/postinst/bootloader-test-error-2.6.26-2-686:
linux-image-2.6.26-2-686/postinst/depmod-error-2.6.26-2-686: false
linux-image-2.6.26-2-686/preinst/bootloader-initrd-2.6.26-2-686: true
linux-image-2.6.26-2-686/postinst/create-kimage-link-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/initrd-2.6.26-2-686:
linux-image-2.6.26-2-686/postinst/kimage-is-a-directory:
linux-image-2.6.26-2-686/postinst/old-initrd-link-2.6.26-2-686: true
linux-image-2.6.26-2-686/prerm/removing-running-kernel-2.6.26-2-686: true
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.26-2-686/postinst/old-dir-initrd-link-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/overwriting-modules-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/abort-overwrite-2.6.26-2-686:
linux-image-2.6.26-2-686/preinst/abort-install-2.6.26-2-686:
linux-image-2.6.26-2-686/postinst/depmod-error-initrd-2.6.26-2-686: false
linux-image-2.6.26-2-686/preinst/failed-to-move-modules-2.6.26-2-686:
linux-image-2.6.26-2-686/preinst/lilo-has-ramdisk:
linux-image-2.6.26-2-686/prerm/would-invalidate-boot-loader-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/elilo-initrd-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/lilo-initrd-2.6.26-2-686: true
linux-image-2.6.26-2-686/postinst/old-system-map-link-2.6.26-2-686: true
Reply to: