Package: linux-image-2.6.18-6-686 Version: 2.6.18.dfsg.1-18etch1
Ibm server 6 disk in raid5 1 HBA Fiber Channel (qla2xxx) On the boot of my linux image, 1 times on 3 it works. When it works My local disk is sda $ dmesg ... qla2xxx 0000:04:04.0: Found an ISP2312, irq 201, iobase 0xf8842000
qla2xxx 0000:04:04.0: Configuring PCI space...
qla2xxx 0000:04:04.0: Configure NVRAM parameters...
qla2xxx 0000:04:04.0: Verifying loaded RISC code...
scsi1 : IBM PCI ServeRAID 7.12.05 Build 761
ICH5: IDE controller at PCI slot 0000:00:1f.1
ACPI: Unable to derive IRQ for device 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A]: no GSI
ICH5: chipset revision 2
ICH5: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x0480-0x0487, BIOS settings: hda:DMA, hdb:DMA
Probing IDE interface ide0...
Vendor: IBM Model: SERVERAID Rev: 1.00
Type: Direct-Access ANSI SCSI revision: 02
Vendor: IBM Model: SERVERAID Rev: 1.00
Type: Processor ANSI SCSI revision: 02
SCSI device sda: 213288960 512-byte hdwr sectors (109204 MB)
sda: assuming Write Enabled
sda: assuming drive cache: write through
SCSI device sda: 213288960 512-byte hdwr sectors (109204 MB)
sda: assuming Write Enabled
sda: assuming drive cache: write through
sda: sda1 sda2 sda3 sda4 < sda5 sda6<5> Vendor: IBM Model: 40K sda76480a S320 0 Rev: 1
Type: Processor ANSI SCSI revision: 02
sda8 >
sd 1:0:0:0: Attached scsi disk sda
qla2xxx 0000:04:04.0: Allocated (412 KB) for firmware dump...
qla2xxx 0000:04:04.0: LIP reset occured (f7f7).
qla2xxx 0000:04:04.0: Waiting for LIP to complete...
usb 3-2: new full speed USB device using uhci_hcd and address 2
usb 3-2: configuration #1 chosen from 1 choice
usbcore: registered new driver hiddev
input: IBM PPC I/F as /class/input/input1
input: USB HID v1.10 Keyboard [IBM PPC I/F] on usb-0000:00:1d.1-2
input: IBM PPC I/F as /class/input/input2
input: USB HID v1.10 Mouse [IBM PPC I/F] on usb-0000:00:1d.1-2
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
hda: HL-DT-STCD-RW/DVD DRIVE GCC-4244N, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
qla2xxx 0000:04:04.0: LOOP UP detected (2 Gbps).
qla2xxx 0000:04:04.0: Topology - (F_Port), Host Loop address 0xffff
scsi0 : qla2xxx
qla2xxx 0000:04:04.0:
QLogic Fibre Channel HBA Driver: 8.01.07-k1
QLogic QLA2340 - 133MHz PCI-X to 2Gb FC, Single Channel
ISP2312: PCI-X (133 MHz) @ 0000:04:04.0 hdma-, host#=0, fw=3.03.20 IPX
Vendor: IBM Model: 1722-600 Rev: 0520
Type: Direct-Access ANSI SCSI revision: 03
SCSI device sdb: 1428495360 512-byte hdwr sectors (731390 MB)
sdb: Write Protect is off
sdb: Mode Sense: 77 00 10 08
SCSI device sdb: drive cache: write back w/ FUA
SCSI device sdb: 1428495360 512-byte hdwr sectors (731390 MB)
sdb: Write Protect is off
sdb: Mode Sense: 77 00 10 08
SCSI device sdb: drive cache: write back w/ FUA
sdb:<6>hda: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
sdb1
sd 0:0:0:0: Attached scsi disk sdb
Vendor: IBM Model: Universal Xport Rev: 0520
Type: Direct-Access ANSI SCSI revision: 03
Vendor: IBM Model: 1722-600 Rev: 0520
Type: Direct-Access ANSI SCSI revision: 03
SCSI device sdc: 1428495360 512-byte hdwr sectors (731390 MB)
sdc: Write Protect is off
sdc: Mode Sense: 77 00 10 08
SCSI device sdc: drive cache: write back w/ FUA
SCSI device sdc: 1428495360 512-byte hdwr sectors (731390 MB)
sdc: Write Protect is off
sdc: Mode Sense: 77 00 10 08
SCSI device sdc: drive cache: write back w/ FUA
sdc: sdc1
sd 0:0:1:0: Attached scsi disk sdc
Vendor: IBM Model: Universal Xport Rev: 0520
Type: Direct-Access ANSI SCSI revision: 03
$ lsscsi [0:0:0:1] disk IBM 1722-600 0520 /dev/sdb
[0:0:1:1] disk IBM 1722-600 0520 /dev/sdc
[1:0:0:0] disk IBM SERVERAID 1.00 /dev/sda
[1:0:15:0] process IBM SERVERAID 1.00 -
[1:2:8:0] process IBM 40K6480a S320 0 1 -
When it works not, it stop the following message: Begin: Waiting for root file system... and my local disk is sdb or sdc It detect the qla2xxx before the local disk. Thanks
|