Bug#430779: linux-image-2.6.21-2-686: System seems to have microhangs, especially the mouse and sound are affected.
dmesg output and lsmod output attached.
Note the lines
PCI: Transparent bridge - 0000:00:1e.0
PCI: Bus #03 (-#06) is hidden behind transparent bridge #02 (-#02) (try
'pci=assign-busses')
Please report the result to linux-kernel to fix this permanently
PCI: Bus #07 (-#0a) is hidden behind transparent bridge #02 (-#02) (try
'pci=assign-busses')
Please report the result to linux-kernel to fix this permanently
PCI: Bus #0b (-#0e) is hidden behind transparent bridge #02 (-#02) (try
'pci=assign-busses')
Please report the result to linux-kernel to fix this permanently
Are these bugs related to this lines?
Willi
Linux version 2.6.21-1-686 (Debian 2.6.21-4) (waldi@debian.org) (gcc version 4.1.3 20070518 (prerelease) (Debian 4.1.2-8)) #1 SMP Sat May 26 16:14:59 UTC 2007
BIOS-provided physical RAM map:
sanitize start
sanitize end
copy_e820_map() start: 0000000000000000 size: 000000000009f800 end: 000000000009f800 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000000009f800 size: 0000000000000800 end: 00000000000a0000 type: 2
copy_e820_map() start: 00000000000ce000 size: 0000000000002000 end: 00000000000d0000 type: 2
copy_e820_map() start: 00000000000dc000 size: 0000000000024000 end: 0000000000100000 type: 2
copy_e820_map() start: 0000000000100000 size: 000000001ede0000 end: 000000001eee0000 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000001eee0000 size: 000000000000c000 end: 000000001eeec000 type: 3
copy_e820_map() start: 000000001eeec000 size: 0000000000014000 end: 000000001ef00000 type: 4
copy_e820_map() start: 000000001ef00000 size: 0000000001100000 end: 0000000020000000 type: 2
copy_e820_map() start: 00000000fec10000 size: 0000000000010000 end: 00000000fec20000 type: 2
copy_e820_map() start: 00000000ff800000 size: 0000000000400000 end: 00000000ffc00000 type: 2
copy_e820_map() start: 00000000fffffc00 size: 0000000000000400 end: 0000000100000000 type: 2
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000ce000 - 00000000000d0000 (reserved)
BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001eee0000 (usable)
BIOS-e820: 000000001eee0000 - 000000001eeec000 (ACPI data)
BIOS-e820: 000000001eeec000 - 000000001ef00000 (ACPI NVS)
BIOS-e820: 000000001ef00000 - 0000000020000000 (reserved)
BIOS-e820: 00000000fec10000 - 00000000fec20000 (reserved)
BIOS-e820: 00000000ff800000 - 00000000ffc00000 (reserved)
BIOS-e820: 00000000fffffc00 - 0000000100000000 (reserved)
0MB HIGHMEM available.
494MB LOWMEM available.
Entering add_active_range(0, 0, 126688) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 126688
HighMem 126688 -> 126688
early_node_map[1] active PFN ranges
0: 0 -> 126688
On node 0 totalpages: 126688
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 957 pages used for memmap
Normal zone: 121635 pages, LIFO batch:31
HighMem zone: 0 pages used for memmap
DMI present.
ACPI: RSDP 000F6040, 0014 (r0 ACER )
ACPI: RSDT 1EEE57BD, 0030 (r1 ACER TM6000 20020608 LTP 0)
ACPI: FACP 1EEEBF2C, 0074 (r1 ACER TM6000 20020608 PTL 50)
ACPI Warning (tbfadt-0360): Ignoring BIOS FADT r1 C-state control [20070126]
ACPI: DSDT 1EEE57ED, 673F (r1 ACER TM6000 20020608 MSFT 100000E)
ACPI: FACS 1EEFCFC0, 0040
ACPI: HPET 1EEEBFA0, 0038 (r1 ACER TM6000 20020608 PTL 0)
ACPI: BOOT 1EEEBFD8, 0028 (r1 ACER TM6000 20020608 LTP 1)
ACPI: PM-Timer IO Port: 0x1008
ACPI: HPET id: 0x8086a201 base: 0x0
Allocating PCI resources starting at 30000000 (gap: 20000000:dec10000)
Built 1 zonelists. Total pages: 125699
Kernel command line: root=/dev/hda10 ro vga=791 resume=/dev/hda6
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (013ea000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Detected 1694.584 MHz processor.
Console: colour dummy device 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 493508k/506752k available (1661k kernel code, 12612k reserved, 637k data, 212k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xfff4f000 - 0xfffff000 ( 704 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xdf800000 - 0xff7fe000 ( 511 MB)
lowmem : 0xc0000000 - 0xdeee0000 ( 494 MB)
.init : 0xc0345000 - 0xc037a000 ( 212 kB)
.data : 0xc029f405 - 0xc033e834 ( 637 kB)
.text : 0xc0100000 - 0xc029f405 (1661 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3391.18 BogoMIPS (lpj=6782372)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: afe9f9bf 00000000 00000000 00000000 00000180 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: After all inits, caps: afe9f9bf 00000000 00000000 00002040 00000180 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 11k freed
ACPI: Core revision 20070126
ACPI: setting ELCR to 0200 (from 0440)
CPU0: Intel(R) Pentium(R) M processor 1.70GHz stepping 06
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd742, last bus=2
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:00:02.0
PCI quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 1180-11bf claimed by ICH4 GPIO
PCI: Transparent bridge - 0000:00:1e.0
PCI: Bus #03 (-#06) is hidden behind transparent bridge #02 (-#02) (try 'pci=assign-busses')
Please report the result to linux-kernel to fix this permanently
PCI: Bus #07 (-#0a) is hidden behind transparent bridge #02 (-#02) (try 'pci=assign-busses')
Please report the result to linux-kernel to fix this permanently
PCI: Bus #0b (-#0e) is hidden behind transparent bridge #02 (-#02) (try 'pci=assign-busses')
Please report the result to linux-kernel to fix this permanently
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs *6)
ACPI: PCI Interrupt Link [LNKB] (IRQs *10)
ACPI: PCI Interrupt Link [LNKC] (IRQs *6)
ACPI: PCI Interrupt Link [LNKD] (IRQs *6)
ACPI: PCI Interrupt Link [LNKE] (IRQs *10)
ACPI: PCI Interrupt Link [LNKF] (IRQs 10) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 6) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs *10)
ACPI: Power Resource [PFN0] (off)
ACPI: Power Resource [PFN1] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 10 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NET: Registered protocol family 8
NET: Registered protocol family 20
pnp: 00:04: iomem range 0xfec10000-0xfec1ffff could not be reserved
pnp: 00:04: iomem range 0xff800000-0xffbfffff could not be reserved
pnp: 00:04: iomem range 0xfff00000-0xffffffff could not be reserved
pnp: 00:04: iomem range 0x0-0x9ffff could not be reserved
Time: tsc clocksource has been installed.
PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
PCI: Bus 3, cardbus bridge: 0000:02:06.0
IO window: 00003000-000030ff
IO window: 00003400-000034ff
PREFETCH window: 30000000-33ffffff
MEM window: 40000000-43ffffff
PCI: Bus 7, cardbus bridge: 0000:02:06.1
IO window: 00003800-000038ff
IO window: 00003c00-00003cff
PREFETCH window: 34000000-37ffffff
MEM window: 44000000-47ffffff
PCI: Bus 11, cardbus bridge: 0000:02:06.3
IO window: 00001400-000014ff
IO window: 00002800-000028ff
PREFETCH window: 38000000-3bffffff
MEM window: 48000000-4bffffff
PCI: Bridge: 0000:00:1e.0
IO window: 3000-3fff
MEM window: e0200000-e07fffff
PREFETCH window: 30000000-3bffffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 6
PCI: setting IRQ 6 as level-triggered
ACPI: PCI Interrupt 0000:02:06.0[A] -> Link [LNKC] -> GSI 6 (level, low) -> IRQ 6
ACPI: PCI Interrupt 0000:02:06.1[A] -> Link [LNKC] -> GSI 6 (level, low) -> IRQ 6
PCI: Enabling device 0000:02:06.3 (0080 -> 0083)
ACPI: PCI Interrupt 0000:02:06.3[A] -> Link [LNKC] -> GSI 6 (level, low) -> IRQ 6
PCI: Setting latency timer of device 0000:02:06.3 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 196608 bytes)
TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
checking if image is initramfs... it is
Switched to high resolution mode on CPU 0
Freeing initrd memory: 5320k freed
Simple Boot Flag at 0x37 set to 0x1
audit: initializing netlink socket (disabled)
audit(1182961404.656:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
vesafb: framebuffer at 0xe8000000, mapped to 0xdf880000, using 3072k, total 16192k
vesafb: mode is 1024x768x16, linelength=2048, pages=9
vesafb: protected mode interface info at 00ff:44f0
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI interrupt for device 0000:00:1f.6 disabled
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:MOU2] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
Freeing unused kernel memory: 212k freed
input: AT Translated Set 2 keyboard as /class/input/input0
ACPI: Transitioning device [FAN0] to D3
ACPI: Transitioning device [FAN0] to D3
ACPI: Fan [FAN0] (off)
ACPI: Transitioning device [FAN1] to D3
ACPI: Transitioning device [FAN1] to D3
ACPI: Fan [FAN1] (off)
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: Thermal Zone [THRM] (45 C)
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 6
ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 6 (level, low) -> IRQ 6
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 6, io base 0x00001820
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 6
ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 6 (level, low) -> IRQ 6
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 6, io base 0x00001840
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 6 (level, low) -> IRQ 6
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 6, io base 0x00001860
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [LNKH] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 10, io mem 0xe0100000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
usb 1-2: new full speed USB device using uhci_hcd and address 2
ieee1394: Initialized config rom entry `ip1394'
ACPI: PCI Interrupt 0000:02:07.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[10] MMIO=[e0218000-e02187ff] Max Packet=[2048] IR/IT contexts=[4/8]
ICH4: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 6 (level, low) -> IRQ 6
ICH4: chipset revision 3
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1810-0x1817, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x1818-0x181f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
Time: acpi_pm clocksource has been installed.
hda: IC25N060ATMR04-0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00c09f000020d815]
usb 4-6: new high speed USB device using ehci_hcd and address 5
hdc: MATSHITADVD-RAM UJ-820S, ATAPI CD/DVD-ROM drive
usb 4-6: configuration #1 chosen from 1 choice
hub 4-6:1.0: USB hub found
hub 4-6:1.0: 4 ports detected
usb 2-1: new low speed USB device using uhci_hcd and address 2
usb 2-1: configuration #1 chosen from 1 choice
ide1 at 0x170-0x177,0x376 on irq 15
tg3.c:v3.75.1 (May 7, 2007)
ACPI: PCI Interrupt 0000:02:02.0[A] -> Link [LNKD] -> GSI 6 (level, low) -> IRQ 6
SCSI subsystem initialized
eth0: Tigon3 [partno(BCM95705A50) rev 3003 PHY(5705)] (PCI:33MHz:32-bit) 10/100/1000Base-T Ethernet 00:c0:9f:4b:4f:b2
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[0] TSOcap[1]
eth0: dma_rwctrl[763f0000] dma_mask[64-bit]
libata version 2.20 loaded.
hda: max request size: 512KiB
hda: 117210240 sectors (60011 MB) w/7884KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
hda: hda1 < hda5 hda6 hda7 hda8 hda9 hda10 hda11<6>usb 2-2: new low speed USB device using uhci_hcd and address 3
hda12 hda13 hda14 hda15 hda16 >
hdc: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
usb 2-2: configuration #1 chosen from 1 choice
usbcore: registered new interface driver hiddev
usb 1-2: new full speed USB device using uhci_hcd and address 3
usb 1-2: configuration #1 chosen from 1 choice
input: HID 1241:1166 as /class/input/input1
input: USB HID v1.10 Mouse [HID 1241:1166] on usb-0000:00:1d.1-1
input: HID 046a:0004 as /class/input/input2
input: USB HID v1.10 Keyboard [HID 046a:0004] on usb-0000:00:1d.1-2
input: HID 046a:0004 as /class/input/input3
input: USB HID v1.10 Device [HID 046a:0004] on usb-0000:00:1d.1-2
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
Attempting manual resume
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
input: PC Speaker as /class/input/input4
Real Time Clock Driver v1.12ac
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
Linux agpgart interface v0.102 (c) Dave Jones
agpgart: Detected an Intel 855 Chipset.
agpgart: Detected 16252K stolen memory.
agpgart: AGP aperture is 128M @ 0xe8000000
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (21-Jan-2007)
ACPI: PCI Interrupt 0000:00:1f.3[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 3 if 0 alt 1 proto 2 vid 0x03F0 pid 0x0C17
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:1f.5 to 64
ieee80211_crypt: registered algorithm 'NULL'
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.0kmq
ipw2200: Copyright(c) 2003-2006 Intel Corporation
Synaptics Touchpad, model: 1, fw: 5.8, id: 0x9d48b1, caps: 0x904713/0x4006
input: SynPS/2 Synaptics TouchPad as /class/input/input5
iTCO_wdt: Found a ICH4-M TCO device (Version=1, TCOBASE=0x1060)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
intel_rng: FWH not detected
intel8x0_measure_ac97_clock: measured 55443 usecs
intel8x0: clocking to 48000
ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:1f.6 to 64
Yenta: CardBus bridge found at 0000:02:06.0 [1025:0050]
Yenta O2: res at 0x94/0xD4: ea/00
Yenta O2: enabling read prefetch/write burst
Yenta: ISA IRQ mask 0x0838, PCI irq 6
Socket status: 30000006
Yenta: Raising subordinate bus# of parent bus (#02) from #02 to #06
pcmcia: parent PCI bridge I/O window: 0x3000 - 0x3fff
cs: IO port probe 0x3000-0x3fff: clean.
pcmcia: parent PCI bridge Memory window: 0xe0200000 - 0xe07fffff
pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x3bffffff
Yenta: CardBus bridge found at 0000:02:06.1 [1025:0050]
Yenta: ISA IRQ mask 0x0838, PCI irq 6
Socket status: 30000006
Yenta: Raising subordinate bus# of parent bus (#02) from #06 to #0a
pcmcia: parent PCI bridge I/O window: 0x3000 - 0x3fff
cs: IO port probe 0x3000-0x3fff: clean.
pcmcia: parent PCI bridge Memory window: 0xe0200000 - 0xe07fffff
pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x3bffffff
Yenta: CardBus bridge found at 0000:02:06.3 [1025:0050]
Yenta: ISA IRQ mask 0x0838, PCI irq 6
Socket status: 30000410
Yenta: Raising subordinate bus# of parent bus (#02) from #0a to #0e
pcmcia: parent PCI bridge I/O window: 0x3000 - 0x3fff
cs: IO port probe 0x3000-0x3fff: clean.
pcmcia: parent PCI bridge Memory window: 0xe0200000 - 0xe07fffff
pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x3bffffff
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 10
ACPI: PCI Interrupt 0000:02:04.0[A] -> Link [LNKE] -> GSI 10 (level, low) -> IRQ 10
ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
pccard: PCMCIA card inserted into slot 2
cs: memory probe 0xe0200000-0xe07fffff: excluding 0xe0200000-0xe025ffff
pcmcia: registering new device pcmcia2.0
ipw2200: ipw2200-bss.fw request_firmware failed: Reason -2
ipw2200: Unable to load firmware: -2
ipw2200: failed to register network device
ACPI: PCI interrupt for device 0000:02:04.0 disabled
ipw2200: probe of 0000:02:04.0 failed with error -5
Adding 1020088k swap on /dev/hda6. Priority:-1 extents:1 across:1020088k
EXT3 FS on hda10, internal journal
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
fuse init (API version 7.8)
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda11, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda9, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda12, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda15, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda16, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
pcmcia: Detected deprecated PCMCIA ioctl usage from process: discover.
pcmcia: This interface will soon be removed from the kernel; please expect breakage unless you upgrade to new tools.
pcmcia: see http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for details.
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ACPI: Battery Slot [BAT1] (battery present)
ACPI: Battery Slot [BAT2] (battery absent)
ACPI: AC Adapter [ACAD] (on-line)
input: Power Button (FF) as /class/input/input6
ACPI: Power Button (FF) [PWRF]
input: Lid Switch as /class/input/input7
ACPI: Lid Switch [LID]
input: Sleep Button (CM) as /class/input/input8
ACPI: Sleep Button (CM) [SLPB]
lp0: using parport0 (interrupt-driven).
ppdev: user-space parallel port driver
PM: Writing back config space on device 0000:02:02.0 at offset c (was 7ef70000, writing 0)
PM: Writing back config space on device 0000:02:02.0 at offset b (was 165d14e4, writing 501025)
PM: Writing back config space on device 0000:02:02.0 at offset 3 (was 0, writing 4008)
PM: Writing back config space on device 0000:02:02.0 at offset 2 (was 2000000, writing 2000003)
PM: Writing back config space on device 0000:02:02.0 at offset 1 (was 2b00000, writing 2b00106)
PM: Writing back config space on device 0000:02:02.0 at offset 0 (was 165d14e4, writing 165314e4)
ADDRCONF(NETDEV_UP): eth0: link is not ready
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (3959 buckets, 31672 max)
eth0: no IPv6 routers present
Clocksource tsc unstable (delta = -186578274 ns)
[drm] Initialized drm 1.1.0 20060810
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKA] -> GSI 6 (level, low) -> IRQ 6
[drm] Initialized i915 1.6.0 20060119 on minor 0
[drm] Initialized i915 1.6.0 20060119 on minor 1
Module Size Used by
i915 21280 2
drm 73908 3 i915
binfmt_misc 10984 1
cpufreq_userspace 4128 0
cpufreq_powersave 1792 0
nfs 222444 0
lockd 58248 1 nfs
nfs_acl 3520 1 nfs
sunrpc 154972 4 nfs,lockd,nfs_acl
ipt_LOG 6144 1
ipt_REJECT 4384 4
xt_tcpudp 3104 16
xt_state 2432 2
nf_conntrack_ftp 9632 0
iptable_nat 7236 0
nf_nat 17740 1 iptable_nat
nf_conntrack_ipv4 17612 4 iptable_nat
nf_conntrack 58472 5 xt_state,nf_conntrack_ftp,iptable_nat,nf_nat,nf_conntrack_ipv4
nfnetlink 6456 3 nf_nat,nf_conntrack_ipv4,nf_conntrack
iptable_filter 2944 1
ip_tables 12164 2 iptable_nat,iptable_filter
x_tables 14468 6 ipt_LOG,ipt_REJECT,xt_tcpudp,xt_state,iptable_nat,ip_tables
tcp_diag 1760 0
inet_diag 11336 2 tcp_diag
ppdev 8580 0
lp 10884 0
button 7952 0
ac 5220 0
battery 10020 0
ipv6 236320 31
fuse 41684 1
dm_snapshot 16420 0
dm_mirror 20116 0
dm_mod 52556 2 dm_snapshot,dm_mirror
tun 10304 0
acpi_cpufreq 8680 1
cpufreq_ondemand 7884 1
freq_table 4512 2 acpi_cpufreq,cpufreq_ondemand
sr_mod 16100 0
sbp2 21188 0
ide_generic 1344 0 [permanent]
pcmcia 35276 0
ipw2200 130628 0
snd_intel8x0m 16716 1
snd_seq_dummy 3748 0
snd_seq_oss 29248 0
ieee80211 30984 1 ipw2200
ieee80211_crypt 5792 1 ieee80211
snd_seq_midi 8160 0
snd_rawmidi 22400 1 snd_seq_midi
firmware_class 9408 2 pcmcia,ipw2200
yenta_socket 24876 5
rsrc_nonstatic 11968 1 yenta_socket
pcmcia_core 36884 3 pcmcia,yenta_socket,rsrc_nonstatic
snd_seq_midi_event 6880 2 snd_seq_oss,snd_seq_midi
snd_intel8x0 32060 2
snd_ac97_codec 92356 2 snd_intel8x0m,snd_intel8x0
snd_seq 46160 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
snd_seq_device 7596 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
ac97_bus 2272 1 snd_ac97_codec
snd_pcm_oss 39168 0
snd_mixer_oss 15328 1 snd_pcm_oss
snd_pcm 71940 4 snd_intel8x0m,snd_intel8x0,snd_ac97_codec,snd_pcm_oss
snd_timer 20868 2 snd_seq,snd_pcm
snd 48132 17 snd_intel8x0m,snd_seq_oss,snd_rawmidi,snd_intel8x0,snd_ac97_codec,snd_seq,snd_seq_device,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer
usblp 13184 0
soundcore 7424 1 snd
i2c_i801 8560 0
iTCO_wdt 9956 0
parport_pc 32740 1
parport 33672 3 ppdev,lp,parport_pc
intel_agp 23004 1
agpgart 32168 3 drm,intel_agp
eth1394 18276 0
snd_page_alloc 9512 3 snd_intel8x0m,snd_intel8x0,snd_pcm
shpchp 30996 0
pci_hotplug 29088 1 shpchp
tsdev 7520 0
i2c_core 20480 1 i2c_i801
psmouse 34952 0
evdev 9216 6
joydev 9152 0
serio_raw 6564 0
rtc 12760 0
pcspkr 3136 0
ext3 120904 9
jbd 55208 1 ext3
mbcache 8164 1 ext3
ide_cd 36512 0
cdrom 32768 2 sr_mod,ide_cd
ide_disk 15648 11
ata_generic 8100 0
libata 109172 1 ata_generic
scsi_mod 133740 3 sr_mod,sbp2,libata
usbhid 23488 0
hid 23680 1 usbhid
piix 9508 0 [permanent]
ohci1394 32432 0
ieee1394 89560 3 sbp2,eth1394,ohci1394
tg3 99812 0
generic 4804 0 [permanent]
ide_core 115016 5 ide_generic,ide_cd,ide_disk,piix,generic
ehci_hcd 30796 0
uhci_hcd 22608 0
usbcore 123304 5 usblp,usbhid,ehci_hcd,uhci_hcd
thermal 14120 0
processor 30888 2 acpi_cpufreq,thermal
fan 4868 0
Reply to: