Bug#312255: Problems booting kernel-image-2.6.8-2-k7
Package: kernel-image-2.6.8-2-k7
Version: 2.6.8-16
Followup-For: Bug #312255
If I boot the system using kernel 2.6, after the message "Starting GNOME
DISPLAY MANAGER: gdm", a messy image appears, similar to my desktop
background: except for the mouse, everything is blocked. To go on I have
to reset: mysteriously, after the reboot I can use kernel 2.6 (sometimes
I have to repeat this procedure many times).
Kernel 2.4, instead, works fine.
I installed the kernel-image-2.6.8-2-k7 package after the installation
of Debian 3.1 "sarge" with kernel-image-2.4.27-2-386.
I use an AMD Athlon XP 1800+ CPU and an ATI Radeon 7000 graphic card on
an ASUS A7V880 motherboard (VIA KT880/VT8237 chipset).
--------
"lspci -v" output:
0000:00:00.0 Host bridge: VIA Technologies, Inc.: Unknown device 0269
(rev 80)
Subsystem: Asustek Computer, Inc.: Unknown device 8122
Flags: bus master, 66MHz, medium devsel, latency 64
Memory at e0000000 (32-bit, prefetchable) [size=256M]
Capabilities: [80] AGP version 3.5
Capabilities: [50] Power Management version 2
0000:00:00.1 Host bridge: VIA Technologies, Inc.: Unknown device 1269
Subsystem: Asustek Computer, Inc.: Unknown device 8122
Flags: bus master, medium devsel, latency 0
0000:00:00.2 Host bridge: VIA Technologies, Inc.: Unknown device 2269
Subsystem: Asustek Computer, Inc.: Unknown device 8122
Flags: bus master, medium devsel, latency 0
0000:00:00.3 Host bridge: VIA Technologies, Inc.: Unknown device 3269
Subsystem: Asustek Computer, Inc.: Unknown device 8122
Flags: bus master, medium devsel, latency 0
0000:00:00.4 Host bridge: VIA Technologies, Inc.: Unknown device 4269
Subsystem: Asustek Computer, Inc.: Unknown device 8122
Flags: bus master, medium devsel, latency 0
0000:00:00.7 Host bridge: VIA Technologies, Inc.: Unknown device 7269
Subsystem: Asustek Computer, Inc.: Unknown device 8122
Flags: bus master, medium devsel, latency 0
0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI Bridge
(prog-if 00 [Normal decode])
Flags: bus master, 66MHz, medium devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fe100000-fe4fffff
Prefetchable memory behind bridge: 9ff00000-afefffff
Capabilities: [70] Power Management version 2
0000:00:0f.0 RAID bus controller: VIA Technologies, Inc. VIA VT6420 SATA
RAID Controller (rev 80)
Subsystem: Asustek Computer, Inc. A7V600 motherboard
Flags: bus master, medium devsel, latency 64, IRQ 20
I/O ports at eff0 [size=8]
I/O ports at efe4 [size=4]
I/O ports at efa8 [size=8]
I/O ports at efe0 [size=4]
I/O ports at ef90 [size=16]
I/O ports at e800 [size=256]
Capabilities: [c0] Power Management version 2
0000:00:0f.1 IDE interface: VIA Technologies, Inc.
VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
(prog-if 8a [Master SecP PriP])
Subsystem: Asustek Computer, Inc. A7V600 motherboard
Flags: bus master, medium devsel, latency 32, IRQ 20
I/O ports at fc00 [size=16]
Capabilities: [c0] Power Management version 2
0000:00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB
1.1 Controller (rev 81) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller
Flags: bus master, medium devsel, latency 64, IRQ 21
I/O ports at eec0 [size=32]
Capabilities: [80] Power Management version 2
0000:00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB
1.1 Controller (rev 81) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller
Flags: bus master, medium devsel, latency 64, IRQ 21
I/O ports at ef00 [size=32]
Capabilities: [80] Power Management version 2
0000:00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB
1.1 Controller (rev 81) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller
Flags: bus master, medium devsel, latency 64, IRQ 21
I/O ports at ef20 [size=32]
Capabilities: [80] Power Management version 2
0000:00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB
1.1 Controller (rev 81) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller
Flags: bus master, medium devsel, latency 64, IRQ 21
I/O ports at ef40 [size=32]
Capabilities: [80] Power Management version 2
0000:00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86)
(prog-if 20 [EHCI])
Subsystem: VIA Technologies, Inc. USB 2.0
Flags: bus master, medium devsel, latency 64, IRQ 21
Memory at fe900000 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
0000:00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge
[K8T800 South] Subsystem: Asustek Computer, Inc. A7V600
motherboard
Flags: bus master, medium devsel, latency 0
Capabilities: [c0] Power Management version 2
0000:00:11.5 Multimedia audio controller: VIA Technologies, Inc.
VT8233/A/8235/8237 AC97 Audio Controller (rev 60)
Subsystem: Asustek Computer, Inc.: Unknown device 810d
Flags: medium devsel, IRQ 22
I/O ports at e000 [size=256]
Capabilities: [c0] Power Management version 2
0000:00:13.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139
Flags: bus master, medium devsel, latency 64, IRQ 18
I/O ports at e400 [size=256]
Memory at feb00000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
0000:01:00.0 VGA compatible controller: ATI Technologies Inc Radeon
RV200 QW [Radeon 7500] (prog-if 00 [VGA])
Subsystem: PC Partner Limited Radeon RV200 QW [Radeon 7500 LE]
Flags: bus master, stepping, 66MHz, medium devsel, latency 64,
IRQ 16
Memory at a0000000 (32-bit, prefetchable) [size=128M]
I/O ports at d000 [size=256]
Memory at fe400000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at fe300000 [disabled] [size=128K]
Capabilities: [58] AGP version 2.0
Capabilities: [50] Power Management version 2
--------
"dmesg" output using kernel 2.4:
Linux version 2.4.27-2-386 (horms@tabatha.lab.ultramonkey.org) (gcc
version 3.3.5 (Debian 1:3.3.5-12)) #1 Mon May 16 16:47:51 JST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ff40000 (usable)
BIOS-e820: 000000001ff40000 - 000000001ff50000 (ACPI data)
BIOS-e820: 000000001ff50000 - 0000000020000000 (ACPI NVS)
BIOS-e820: 00000000ff7c0000 - 0000000100000000 (reserved)
511MB LOWMEM available.
found SMP MP-table at 000ff780
hm, page 000ff000 reserved twice.
hm, page 00100000 reserved twice.
hm, page 000f0000 reserved twice.
hm, page 000f1000 reserved twice.
On node 0 totalpages: 130880
zone(0): 4096 pages.
zone(1): 126784 pages.
zone(2): 0 pages.
ACPI: RSDP (v000 ACPIAM ) @
0x000f91a0
ACPI: RSDT (v001 A M I OEMRSDT 0x09000424 MSFT 0x00000097) @
0x1ff40000
ACPI: FADT (v002 A M I OEMFACP 0x09000424 MSFT 0x00000097) @
0x1ff40200
ACPI: MADT (v001 A M I OEMAPIC 0x09000424 MSFT 0x00000097) @
0x1ff40300
ACPI: OEMB (v001 A M I OEMBIOS 0x09000424 MSFT 0x00000097) @
0x1ff50040
ACPI: DSDT (v001 A0008 A0008705 0x00000705 INTL 0x02002026) @
0x00000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 Pentium(tm) Pro APIC version 16
Using ACPI for processor (LAPIC) configuration information
Intel MultiProcessor Specification v1.1
Virtual Wire compatibility mode.
OEM ID: ASUSTek Product ID: A7V880 APIC at: 0xFEE00000
I/O APIC #1 Version 3 at 0xFEC00000.
Enabling APIC mode: Flat. Using 1 I/O APICs
Processors: 1
Kernel command line: root=/dev/hda1 ro
Initializing CPU#0
Detected 1533.449 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 3060.53 BogoMIPS
Memory: 511876k/523520k available (1069k kernel code, 11256k reserved,
459k data, 96k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After generic, caps: 0383fbff c1c3fbff 00000000 00000000
CPU: Common caps: 0383fbff c1c3fbff 00000000 00000000
CPU: AMD Athlon(tm) XP 1800+ stepping 02
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000080
ESR value after enabling vector: 00000000
ENABLING IO-APIC IRQs
Setting 1 in the phys_id_present_map
....changing IO-APIC physical APIC ID to 1 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 1-0, 1-17, 1-19, 1-23 not connected.
...TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 25.
number of IO-APIC #1 registers: 24.
testing the IO APIC.......................
IO APIC #1......
..... register #00: 01000000
........ : physical APIC id: 01
........ : Delivery Type: 0
........ : LTS : 0
..... register #01: 00178003
........ : max redirection entries: 0017
........ : PRQ implemented: 1
........ : IO APIC version: 0003
..... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 001 01 0 0 0 0 0 1 1 51
06 001 01 0 0 0 0 0 1 1 59
07 001 01 0 0 0 0 0 1 1 61
08 001 01 0 0 0 0 0 1 1 69
09 001 01 0 0 0 0 0 1 1 71
0a 001 01 0 0 0 0 0 1 1 79
0b 001 01 0 0 0 0 0 1 1 81
0c 001 01 0 0 0 0 0 1 1 89
0d 001 01 0 0 0 0 0 1 1 91
0e 001 01 0 0 0 0 0 1 1 99
0f 001 01 0 0 0 0 0 1 1 A1
10 001 01 1 1 0 1 0 1 1 A9
11 000 00 1 0 0 0 0 0 0 00
12 001 01 1 1 0 1 0 1 1 B1
13 000 00 1 0 0 0 0 0 0 00
14 001 01 1 1 0 1 0 1 1 B9
15 001 01 1 1 0 1 0 1 1 C1
16 001 01 1 1 0 1 0 1 1 C9
17 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ18 -> 0:18
IRQ20 -> 0:20
IRQ21 -> 0:21
IRQ22 -> 0:22
..................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
...... CPU clock speed is 1533.4062 MHz.
...... host bus clock speed is 266.6793 MHz.
cpu: 0, clocks: 2666793, slice: 1333396
CPU0<T0:2666784,T1:1333376,D:12,S:1333396,C:2666793>
ACPI: Subsystem revision 20040326
ACPI: Interpreter disabled.
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: ACPI tables contain no PCI IRQ routing entries
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router default [1106/3227] at 00:11.0
PCI->APIC IRQ transform: (B0,I15,P1) -> 20
PCI->APIC IRQ transform: (B0,I15,P0) -> 20
PCI->APIC IRQ transform: (B0,I16,P0) -> 21
PCI->APIC IRQ transform: (B0,I16,P0) -> 21
PCI->APIC IRQ transform: (B0,I16,P1) -> 21
PCI->APIC IRQ transform: (B0,I16,P1) -> 21
PCI->APIC IRQ transform: (B0,I16,P2) -> 21
PCI->APIC IRQ transform: (B0,I17,P2) -> 22
PCI->APIC IRQ transform: (B0,I19,P0) -> 18
PCI->APIC IRQ transform: (B1,I0,P0) -> 16
PCI: Via IRQ fixup for 00:10.3, from 3 to 5
PCI: Via IRQ fixup for 00:10.2, from 3 to 5
PCI: Via IRQ fixup for 00:10.1, from 11 to 5
PCI: Via IRQ fixup for 00:10.0, from 11 to 5
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT
SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
COMX: driver version 0.85 (C) 1995-1999 ITConsult-Pro Co. <info@itc.hu>
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 3692 blocks [1 disk] into ram disk... done.
Freeing initrd memory: 3692k freed
VFS: Mounted root (cramfs filesystem).
Freeing unused kernel memory: 96k freed
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
ide: late registration of driver.
VP_IDE: IDE controller at PCI slot 00:0f.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci00:0f.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA
hda: Maxtor 6E040L0, ATA DISK drive
blk: queue e0825b60, I/O limit 4095Mb (mask 0xffffffff)
hdc: LITEON DVD-ROM LTD-165H, ATAPI CD/DVD-ROM drive
hdd: TSSTcorpCD/DVDW TS-H552U, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: 80293248 sectors (41110 MB) w/2048KiB Cache, CHS=79656/16/63,
UDMA(133)
Partition check:
/dev/ide/host0/bus0/target0/lun0: [PTBL] [4998/255/63] p1 p2 < p5 p6 >
Journalled Block Device driver loaded
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Adding Swap: 979924k swap-space (priority -1)
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,1), internal journal
Real Time Clock Driver v1.10f
hdc: attached ide-cdrom driver.
hdc: ATAPI 48X DVD-ROM drive, 256kB Cache
Uniform CD-ROM driver Revision: 3.12
hdd: attached ide-cdrom driver.
hdd: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,6), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
lp: driver loaded but no devices found
8139too Fast Ethernet driver 0.9.26
eth0: RealTek RTL8139 at 0xe400, 00:40:95:32:59:60, IRQ 18
eth0: Identified 8139 chip type 'RTL-8139C'
8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
via82xx: Assuming DXS channels with 48k fixed sample rate.
Please try dxs_support=1 or dxs_support=4 option
and report if it works on your machine.
PCI: Setting latency timer of device 00:11.5 to 64
ALSA ../alsa-kernel/pci/via82xx.c:582: codec_read: codec 0 is not valid
[0x107e5368]
ALSA ../alsa-kernel/pci/via82xx.c:582: codec_read: codec 0 is not valid
[0x107e5368]
ALSA ../alsa-kernel/pci/via82xx.c:582: codec_read: codec 0 is not valid
[0x107e5368]
ALSA ../alsa-kernel/pci/via82xx.c:582: codec_read: codec 0 is not valid
[0x107e5368]
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
ehci_hcd 00:10.4: VIA Technologies, Inc. USB 2.0
ehci_hcd 00:10.4: irq 21, pci mem e09c9000
usb.c: new USB bus registered, assigned bus number 1
ehci_hcd 00:10.4: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29/2.4
hub.c: USB hub found
hub.c: 8 ports detected
uhci.c: USB Universal Host Controller Interface driver v1.1
uhci.c: USB UHCI at I/O 0xef40, IRQ 21
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
uhci.c: USB UHCI at I/O 0xef20, IRQ 21
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
uhci.c: USB UHCI at I/O 0xef00, IRQ 21
usb.c: new USB bus registered, assigned bus number 4
hub.c: USB hub found
hub.c: 2 ports detected
uhci.c: USB UHCI at I/O 0xeec0, IRQ 21
usb.c: new USB bus registered, assigned bus number 5
hub.c: USB hub found
hub.c: 2 ports detected
SCSI subsystem driver Revision: 1.00
libata version 1.02 loaded.
sata_via version 0.20
sata_via(00:0f.0): routed to hard irq line 4
ata1: SATA max UDMA/133 cmd 0xEFF0 ctl 0xEFE6 bmdma 0xEF90 irq 20
ata2: SATA max UDMA/133 cmd 0xEFA8 ctl 0xEFE2 bmdma 0xEF98 irq 20
ata1: no device found (phy stat 00000000)
ata2: no device found (phy stat 00000000)
scsi0 : sata_via
scsi1 : sata_via
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x1001
hub.c: new USB device 00:10.0-1, assigned address 2
usb.c: USB device 2 (vend/prod 0x3f0/0x7304) is not claimed by any
active driver.
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x1001
usb.c: registered new driver usblp
printer.c: usblp0: USB Bidirectional printer dev 2 if 0 alt 0 proto 2
vid 0x03F0 pid 0x7304
printer.c: v0.13: USB Printer Device Class driver
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
[drm] Initialized radeon 1.7.0 20020828 on minor 0
[drm:radeon_unlock] *ERROR* Process 1400 using kernel context 0
--------
"dmesg" output using kernel 2.6:
: 126784 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 ACPIAM ) @
0x000f91a0
ACPI: RSDT (v001 A M I OEMRSDT 0x09000424 MSFT 0x00000097) @
0x1ff40000
ACPI: FADT (v002 A M I OEMFACP 0x09000424 MSFT 0x00000097) @
0x1ff40200
ACPI: MADT (v001 A M I OEMAPIC 0x09000424 MSFT 0x00000097) @
0x1ff40300
ACPI: OEMB (v001 A M I OEMBIOS 0x09000424 MSFT 0x00000097) @
0x1ff50040
ACPI: DSDT (v001 A0008 A0008705 0x00000705 INTL 0x02002026) @
0x00000000
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:6 APIC version 16
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: Assigned apic_id 1
IOAPIC[0]: apic_id 1, version 3, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Built 1 zonelists
Kernel command line: root=/dev/hda1 ro
Initializing CPU#0
PID hash table entries: 2048 (order 11: 16384 bytes)
Detected 1533.339 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 510708k/523520k available (1536k kernel code, 12028k reserved,
697k data, 148k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode...
Ok.
Calibrating delay loop... 3031.04 BogoMIPS
Security Scaffold v1.0.0 initialized
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000020
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD Athlon(tm) XP 1800+ stepping 02
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000080
ESR value after enabling vector: 00000000
ENABLING IO-APIC IRQs
init IO_APIC IRQs
IO-APIC (apicid-pin) 1-0, 1-16, 1-17, 1-18, 1-19, 1-20, 1-21, 1-22,
1-23 not connected.
...TIMER: vector=0x31 pin1=2 pin2=-1
Using local APIC timer interrupts.
calibrating APIC timer ...
...... CPU clock speed is 1533.0239 MHz.
...... host bus clock speed is 266.0650 MHz.
checking if image is initramfs...it isn't (ungzip failed); looks like an
initrd
Freeing initrd memory: 4468k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00f48a0
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x548a, dseg 0xf0000
PNPBIOS fault.. attempting recovery.
PnPBIOS: Warning! Your PnP BIOS caused a fatal error. Attempting to
continue
PnPBIOS: You may need to reboot with the "nobiospnp" option to operate
stably
PnPBIOS: Check with your vendor for an updated BIOS
PnPBIOS: get_dev_node: unexpected status 0x28
PnPBIOS: 6 nodes reported by PnP BIOS; 6 recorded by driver
PCI: Using ACPI for IRQ routing
ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 18 (level, low) -> IRQ 169
ACPI: PCI interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 177
ACPI: PCI interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 177
ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 185
ACPI: PCI interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 185
ACPI: PCI interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 185
ACPI: PCI interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 185
ACPI: PCI interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 185
ACPI: PCI interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 193
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 201
number of MP IRQ sources: 15.
number of IO-APIC #1 registers: 24.
testing the IO APIC.......................
IO APIC #1......
..... register #00: 01000000
........ : physical APIC id: 01
........ : Delivery Type: 0
........ : LTS : 0
..... register #01: 00178003
........ : max redirection entries: 0017
........ : PRQ implemented: 1
........ : IO APIC version: 0003
..... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 001 01 0 0 0 0 0 1 1 51
06 001 01 0 0 0 0 0 1 1 59
07 001 01 0 0 0 0 0 1 1 61
08 001 01 0 0 0 0 0 1 1 69
09 001 01 0 1 0 1 0 1 1 71
0a 001 01 0 0 0 0 0 1 1 79
0b 001 01 0 0 0 0 0 1 1 81
0c 001 01 0 0 0 0 0 1 1 89
0d 001 01 0 0 0 0 0 1 1 91
0e 001 01 0 0 0 0 0 1 1 99
0f 001 01 0 0 0 0 0 1 1 A1
10 001 01 1 1 0 1 0 1 1 C9
11 000 00 1 0 0 0 0 0 0 00
12 001 01 1 1 0 1 0 1 1 A9
13 000 00 1 0 0 0 0 0 0 00
14 001 01 1 1 0 1 0 1 1 B1
15 001 01 1 1 0 1 0 1 1 B9
16 001 01 1 1 0 1 0 1 1 C1
17 000 00 1 0 0 0 0 0 0 00
Using vector-based indexing
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ201 -> 0:16
IRQ169 -> 0:18
IRQ177 -> 0:20
IRQ185 -> 0:21
IRQ193 -> 0:22
..................................... done.
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
PCI: Via IRQ fixup for 0000:00:10.3, from 3 to 9
PCI: Via IRQ fixup for 0000:00:10.2, from 3 to 9
PCI: Via IRQ fixup for 0000:00:10.1, from 11 to 9
PCI: Via IRQ fixup for 0000:00:10.0, from 11 to 9
PCI: Via IRQ fixup for 0000:00:11.5, from 10 to 1
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing
enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI: (supports S0 S1 S3 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4468 blocks [1 disk] into ram disk... done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 148k freed
vesafb: probe of vesafb0 failed with error -6
NET: Registered protocol family 1
SCSI subsystem initialized
libata version 1.02 loaded.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
ACPI: PCI interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 177
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA
hda: Maxtor 6E040L0, ATA DISK drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 80293248 sectors (41110 MB) w/2048KiB Cache, CHS=65535/16/63,
UDMA(133)
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 >
hdc: LITEON DVD-ROM LTD-165H, ATAPI CD/DVD-ROM drive
hdd: TSSTcorpCD/DVDW TS-H552U, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Adding 979924k swap on /dev/hda5. Priority:-1 extents:1
EXT3 FS on hda1, internal journal
hdc: ATAPI 48X DVD-ROM drive, 256kB Cache
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
input: PS/2 Logitech Mouse on isa0060/serio1
Capability LSM initialized
mice: PS/2 mouse device common for all mice
ts: Compaq touchscreen protocol output
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 18 (level, low) -> IRQ 169
sk98lin: Network Device Driver v6.23
(C)Copyright 1999-2004 Marvell(R).
ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 18 (level, low) -> IRQ 169
eth0: Yukon Gigabit Ethernet 10/100/1000Base-T Adapter
PrefPort:A RlmtMode:Check Link State
sata_via version 0.20
ACPI: PCI interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 177
sata_via(0000:00:0f.0): routed to hard irq line 10
ata1: SATA max UDMA/133 cmd 0xEFF0 ctl 0xEFE6 bmdma 0xEF90 irq 177
ata2: SATA max UDMA/133 cmd 0xEFA8 ctl 0xEFE2 bmdma 0xEF98 irq 177
ata1: no device found (phy stat 00000000)
scsi0 : sata_via
ata2: no device found (phy stat 00000000)
scsi1 : sata_via
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 185
uhci_hcd 0000:00:10.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller
uhci_hcd 0000:00:10.0: irq 185, io base 0000eec0
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 185
uhci_hcd 0000:00:10.1: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (#2)
uhci_hcd 0000:00:10.1: irq 185, io base 0000ef00
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 185
uhci_hcd 0000:00:10.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (#3)
uhci_hcd 0000:00:10.2: irq 185, io base 0000ef20
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 185
uhci_hcd 0000:00:10.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (#4)
uhci_hcd 0000:00:10.3: irq 185, io base 0000ef40
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-1: new full speed USB device using address 2
ACPI: PCI interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 185
ehci_hcd 0000:00:10.4: VIA Technologies, Inc. USB 2.0
ehci_hcd 0000:00:10.4: irq 185, pci mem e08a1000
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:10.4: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
drivers/usb/class/usblp.c: can't set desired altsetting 0 on interface 0
usblp: probe of 1-1:1.0 failed with error -5
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
usb 1-1: USB disconnect, address 2
via82xx: Assuming DXS channels with 48k fixed sample rate.
Please try dxs_support=1 or dxs_support=4 option
and report if it works on your machine.
ACPI: PCI interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 193
PCI: Setting latency timer of device 0000:00:11.5 to 64
codec_read: codec 0 is not valid [0x107e5368]
codec_read: codec 0 is not valid [0x107e5368]
codec_read: codec 0 is not valid [0x107e5368]
codec_read: codec 0 is not valid [0x107e5368]
usb 1-1: new full speed USB device using address 3
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 3 if 0
alt 0 proto 2 vid 0x03F0 pid 0x7304
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected VIA KT880 chipset
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: AGP aperture is 256M @ 0xe0000000
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.4
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Real Time Clock Driver v1.12
NET: Registered protocol family 17
eth0: network connection up using port A
speed: 100
autonegotiation: yes
duplex mode: full
flowctrl: none
irq moderation: disabled
scatter-gather: enabled
lp: driver loaded but no devices found
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02fc1a0(lo)
IPv6 over IPv4 tunneling driver
[drm] Initialized radeon 1.11.0 20020828 on minor 0: ATI Technologies
Inc Radeon RV200 QW [Radeon 7500]
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: Device is in legacy mode, falling back to 2.x
agpgart: Putting AGP V2 device at 0000:00:00.0 into 0x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 0x mode
eth0: no IPv6 routers present
-- System Information:
Debian Release: 3.1
Architecture: i386 (i686)
Kernel: Linux 2.4.27-2-386
Locale: LANG=it_IT@euro, LC_CTYPE=it_IT@euro (charmap=ISO-8859-15)
Versions of packages kernel-image-2.6.8-2-k7 depends on:
ii coreutils [fileutils] 5.2.1-2 The GNU core utilities
ii initrd-tools 0.1.81.1 tools to create initrd image for p
ii module-init-tools 3.2-pre1-2 tools for managing Linux kernel mo
-- no debconf information
Reply to: