Bug#304944: kernel-image-2.6.11-powerpc: eth0 and eth1 are swapped
Package: kernel-image-2.6.11-powerpc
Version: 2.6.11-1
Severity: important
I was wondering why the network didn't work...
With older kernels (e.g. 2.6.8), dmesg gives:
[...]
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1223 $ Ben Collins <bcollins@debian.org>
ohci1394: fw-host0: Unexpected PCI resource length of 1000!
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[40] MMIO=[f5000000-f50007ff] Max Packet=[2048]
sungem.c:v0.98 8/24/03 David S. Miller (davem@redhat.com)
divert: allocating divert_blk for eth0
eth0: Sun GEM (PCI) 10/100/1000BaseT Ethernet 00:30:65:cc:59:74
PHY ID: 4061e3, addr: 0
eth0: Found BCM5221 PHY
ieee1394: Host added: ID:BUS[0-00:1023] GUID[003065fffecc5974]
ieee1394: got invalid ack 252 from node 65535 (tcode 0)
ip1394: $Rev: 1224 $ Ben Collins <bcollins@debian.org>
divert: not allocating divert_blk for non-ethernet device eth1
ip1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
hdc: ATAPI 46X DVD-ROM drive, 512kB Cache, (U)DMA
Uniform CD-ROM driver Revision: 3.20
PHY ID: 4061e3, addr: 0
eth0: Link is up at 100 Mbps, full-duplex.
eth0: Pause is disabled
[...]
With 2.6.11, dmesg gives:
[...]
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1223 $ Ben Collins <bcollins@debian.org>
ohci1394: fw-host0: Unexpected PCI resource length of 1000!
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[40] MMIO=[f5000000-f50007ff] Max Packet=[2048]
ieee1394: Host added: ID:BUS[0-00:1023] GUID[003065fffecc5974]
ieee1394: got invalid ack 252 from node 65535 (tcode 0)
eth1394: $Rev: 1224 $ Ben Collins <bcollins@debian.org>
eth1394: eth0: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
sungem.c:v0.98 8/24/03 David S. Miller (davem@redhat.com)
eth1: Sun GEM (PCI) 10/100/1000BaseT Ethernet 00:30:65:cc:59:74
PHY ID: 4061e3, addr: 0
eth1: Found BCM5221 PHY
[...]
The consequence is that the network doesn't work by default at boot
time with the 2.6.11 kernel.
-- System Information:
Debian Release: 3.1
APT prefers testing
APT policy: (900, 'testing'), (200, 'unstable')
Architecture: powerpc (ppc)
Kernel: Linux 2.6.8
Locale: LANG=POSIX, LC_CTYPE=en_US.ISO8859-1 (charmap=ISO-8859-1)
Versions of packages kernel-image-2.6.11-powerpc depends on:
ii initrd-tools 0.1.77 tools to create initrd image for p
ii mkvmlinuz 13 create a kernel to boot a PowerPC
ii module-init-tools 3.2-pre1-2 tools for managing Linux kernel mo
-- no debconf information
Reply to: