Ho provato a seguire i tuoi consigli (Mattia) ma o ho sbagliato
qualcosa o non trovo il driver giusto o c'è qualcosaltro.
Posto quindi dmesg e /proc/cpuinfo.
dmesg:
Linux version 2.6.9-486 (root@primo) (gcc version 3.3.5
(Debian 1:3.3.5-8)) #1 Sun Apr 17 21:34:55 CEST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001effa000 (usable)
BIOS-e820: 000000001effa000 - 000000001efff000 (ACPI data)
BIOS-e820: 000000001efff000 - 000000001f000000 (ACPI NVS)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
495MB LOWMEM available.
On node 0 totalpages: 126970
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 122874 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 ASUS ) @ 0x000f6420
ACPI: RSDT (v001 ASUS L4000L 0x42302e31 MSFT 0x31313031) @
0x1effa000
ACPI: FADT (v001 ASUS L4000L 0x42302e31 MSFT 0x31313031) @
0x1effa080
ACPI: BOOT (v001 ASUS L4000L 0x42302e31 MSFT 0x31313031) @
0x1effa040
ACPI: DSDT (v001 ASUS L4000L 0x00001000 MSFT 0x0100000e) @
0x00000000
Built 1 zonelists
Kernel command line: root=/dev/hda3 ro
No local APIC present or hardware disabled
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 2390.572 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 496680k/507880k available (1607k kernel code, 10640k reserved,
783k data, 136k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor
mode... Ok.
Calibrating delay loop... 4718.59 BogoMIPS (lpj=2359296)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: bfebf9ff 00000000 00000000 00000000
CPU: After vendor identify, caps: bfebf9ff 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: After all inits, caps: bfebf9ff 00000000 00000000 00000080
CPU: Intel Mobile Intel(R) Pentium(R) 4 - M CPU 2.40GHz stepping 09
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: IRQ9 SCI: Edge set to Level Trigger.
checking if image is initramfs...it isn't (ungzip failed); looks like
an initrd
Freeing initrd memory: 3472k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xf1860, last bus=1
PCI: Using configuration type 1
ACPI: Subsystem revision 20040816
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Interrupt Link [LNKA] (IRQs 4) *11
ACPI: PCI Interrupt Link [LNKB] (IRQs 7) *11
ACPI: PCI Interrupt Link [LNKC] (IRQs 4 7 10) *11
ACPI: PCI Interrupt Link [LNKD] (IRQs 4 7 10) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 5 11) *10
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 5 11) *10
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 5 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 5 11) *10
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
Uncovering SIS962 that hid as a SIS503 (compatible=1)
Enabling SiS 96x SMBus.
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: Power Resource [FN0] (on)
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 7
ACPI: PCI interrupt 0000:00:02.1[B] -> GSI 7 (level, low) -> IRQ 7
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
ACPI: PCI interrupt 0000:00:02.6[C] -> GSI 10 (level, low) -> IRQ
10
ACPI: PCI interrupt 0000:00:02.7[C] -> GSI 10 (level, low) -> IRQ
10
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:03.0[A] -> GSI 11 (level, low) -> IRQ
11
ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:03.1[B] -> GSI 11 (level, low) -> IRQ
11
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:03.3[D] -> GSI 11 (level, low) -> IRQ
11
ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 7 (level, low) -> IRQ 7
ACPI: PCI interrupt 0000:00:0a.1[A] -> GSI 7 (level, low) -> IRQ 7
ACPI: PCI interrupt 0000:00:0d.0[A] -> GSI 10 (level, low) -> IRQ
10
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 4
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 4 (level, low) -> IRQ 4
Simple Boot Flag at 0x3a set to 0x1
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
Loaded prism54 driver, version 1.2
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
input: ImPS/2 Generic Wheel Mouse on isa0060/serio4
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
Software Suspend Core
Software Suspend text mode support loading.
Software Suspend LZF Compression Driver registering.
Software Suspend Swap Writer registering.
ACPI: (supports S0 S1 S3 S4 S5)
ACPI wakeup devices:
LID PCI0 PCI1 USB0 USB1 USB3 MC97 LAN
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 3472KiB [1 disk] into ram disk... done.
VFS: Mounted root (cramfs filesystem) readonly.
Software Suspend 2.1: You need to use a resume2= command line parameter
to tell Software Suspend 2 where to look for an image.
Software Suspend 2.1: Missing or invalid storage location (resume2=
parameter). Please correct and rerun lilo (or equivalent) before
suspending.
Freeing unused kernel memory: 136k freed
NET: Registered protocol family 1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
SIS5513: IDE controller at PCI slot 0000:00:02.5
SIS5513: chipset revision 0
SIS5513: not 100% native mode: will probe irqs later
SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller
ide0: BM-DMA at 0xb800-0xb807, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xb808-0xb80f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: IC25N040ATMR04-0, ATA DISK drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 1024KiB
hda: 78140160 sectors (40007 MB) w/1740KiB Cache, CHS=16383/255/63,
UDMA(100)
hda: cache flushes supported
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3 p4 < p5 >
Probing IDE interface ide1...
hdc: TOSHIBA DVD-ROM SD-R2312, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
ide2: Wait for ready failed before probe !
Probing IDE interface ide3...
ide3: Wait for ready failed before probe !
Probing IDE interface ide4...
ide4: Wait for ready failed before probe !
Probing IDE interface ide5...
ide5: Wait for ready failed before probe !
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Adding 497972k swap on /dev/hda5. Priority:-1 extents:1
EXT3 FS on hda3, internal journal
Real Time Clock Driver v1.12
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ieee1394: Initialized config rom entry `ip1394'
SCSI subsystem initialized
sbp2: $Rev: 1219 $ Ben Collins <bcollins@debian.org>
ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 7 (level, low) -> IRQ 7
Yenta: CardBus bridge found at 0000:00:0a.0 [1043:1781]
Yenta: ISA IRQ mask 0x0028, PCI irq 7
Socket status: 30000820
ohci1394: $Rev: 1223 $ Ben Collins <bcollins@debian.org>
ACPI: PCI interrupt 0000:00:0a.1[A] -> GSI 7 (level, low) -> IRQ 7
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[7]
MMIO=[e9800000-e98007ff] Max Packet=[2048]
b44.c:v0.94 (May 4, 2004)
ACPI: PCI interrupt 0000:00:0d.0[A] -> GSI 10 (level, low) -> IRQ
10
eth0: Broadcom 4400 10/100BaseT Ethernet 00:0c:6e:8a:ec:e7
PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 7 (level, low) -> IRQ 7
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI interrupt 0000:00:03.0[A] -> GSI 11 (level, low) -> IRQ
11
ohci_hcd 0000:00:03.0: Silicon Integrated Systems [SiS] USB 1.0
Controller
ohci_hcd 0000:00:03.0: irq 11, pci mem df9de000
ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ACPI: PCI interrupt 0000:00:03.1[B] -> GSI 11 (level, low) -> IRQ
11
ohci_hcd 0000:00:03.1: Silicon Integrated Systems [SiS] USB 1.0
Controller (#2)
ohci_hcd 0000:00:03.1: irq 11, pci mem df9e0000
ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e01800030ca789]
eth1394: $Rev: 1224 $ Ben Collins <bcollins@debian.org>
eth1394: eth2: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected SiS 650 chipset
agpgart: Maximum main memory to use for agp memory: 424M
agpgart: AGP aperture is 64M @ 0xec000000
Serial: 8250/16550 driver $Revision: 1.90 $ 14 ports, IRQ sharing
disabled
ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A
ACPI: PCI interrupt 0000:00:02.6[C] -> GSI 10 (level, low) -> IRQ
10
ACPI: PCI interrupt 0000:00:02.7[C] -> GSI 10 (level, low) -> IRQ
10
intel8x0_measure_ac97_clock: measured 49365 usecs
intel8x0: clocking to 48000
ACPI: PCI interrupt 0000:00:03.3[D] -> GSI 11 (level, low) -> IRQ
11
ehci_hcd 0000:00:03.3: Silicon Integrated Systems [SiS] USB 2.0
Controller
ehci_hcd 0000:00:03.3: irq 11, pci mem dfa9a000
ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 3
PCI: cache line size of 128 is not supported by device 0000:00:03.3
ehci_hcd 0000:00:03.3: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 6 ports detected
eth1: islpci_open()
eth1: resetting device...
eth1: uploading firmware...
eth1: firmware uploaded done, now triggering reset...
NET: Registered protocol family 17
b44: eth0: Link is down.
ACPI: Battery Slot [BAT0] (battery present)
ACPI: AC Adapter [AC] (on-line)
ACPI: Processor [CPU0] (supports C1 C2, 8 throttling states)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Fan [FAN0] (on)
ACPI: Thermal Zone [THRM] (55 C)
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
lp0: using parport0 (polling).
NET: Registered protocol family 5
cs: IO port probe 0x0100-0x04ff: excluding 0x480-0x48f 0x4d0-0x4d7
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0a00-0x0aff: clean.
NET: Registered protocol family 10
Disabled Privacy Extensions on device c0319980(lo)
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
eth1: no IPv6 routers present
eth0: no IPv6 routers present
/proc/cpuinfo:
processor : 0
vendor_id : GenuineIntel
cpu family : 15
model : 2
model name : Mobile Intel(R) Pentium(R) 4 - M CPU 2.40GHz
stepping : 9
cpu MHz : 2390.572
cache size : 512 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov
pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe cid xtpr
bogomips : 4718.59
Grazie dell'aiuto e scusa a tutti se la mail è lunga.
|