Re: errore di copia incolla......... sempre problema su laptop con knoppix
On Wed, 1 Oct 2003 10:39:00 +0200
Mattia Dongili <dongili@supereva.it> wrote:
> Non incominciare un nuovo thread per lo stesso argomento.
Scusate...spero che stavolta vada a finire nello stesso thread visto che ho fatto reply
> e non hai controllato in cosa differisce l'output di ifconfig e route
> tra mandrake e knoppix?
si l'avevo fatto e l'ho rifatto ma anche riportando la stessa configurazione non pingo
Questa e' route -n su mandrake9.1
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0
127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo
0.0.0.0 192.168.0.3 0.0.0.0 UG 0 0 0 eth0
su knoppix laptop ho dato i seguenti comandi:
route add -host 127.0.0.1 dev lo
route add default gw 192.168.0.3
> uh... provato ad usare acpi? (con mandrake l'audio funziona?)
Appena installo mandrake l'audio non va...poi tolgo acpi=off da lilo.conf
cambio il modulo di gestione della scheda da i810_audio a snd-intel8x0(mi sa che e' alsa questo) e tutto parte.
Anche la visualizzazione dell'autonomia inizialmente non va poi installo dei pacchetti relativi ad acpi e tutto parte.....su mandrake funzia tutto.
Su knoppix l'acpi sembra non andare tanto che appena attivo il risparmio energetico nel centro di controllo
qusta finestra crasha....inoltre al boot ci sono delle scritte strane che sul desktop non ho..qualcosa tipo
PCI--------------> APIC IRQ transform + valori esadecimali.. spariscono subito visto che il boot e' velocissimo.
Alsa dovrebbe supportare questo chipset: ho preso l'ultima versione e l'ho compilata seguendo l'how-to di alsa per AC'97 ma il modulo non va su..
Ammesso che qui l'acpi funzioni potresti dirmi come abilitarlo?
ti riporto l'output di dmesg dopo che fallisco l'inserimento di snd-intel8x0
root@whiterabbit:/home/knoppix# dmesg
Linux version 2.4.22-xfs (root@Knoppix) (gcc version 2.95.4 20011002 (Debian prerelease)) #1 SMP Fr Sep 19 17:55:45 CEST 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000f760000 (usable)
BIOS-e820: 000000000f760000 - 000000000f76e000 (ACPI data)
BIOS-e820: 000000000f76e000 - 000000000f780000 (ACPI NVS)
BIOS-e820: 000000000f780000 - 0000000010000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ff800000 - 00000000ffc00000 (reserved)
BIOS-e820: 00000000fffffc00 - 0000000100000000 (reserved)
0MB HIGHMEM available.
247MB LOWMEM available.
found SMP MP-table at 000f5cc0
hm, page 000f5000 reserved twice.
hm, page 000f6000 reserved twice.
hm, page 0009f000 reserved twice.
hm, page 000a0000 reserved twice.
On node 0 totalpages: 63328
zone(0): 4096 pages.
zone(1): 59232 pages.
zone(2): 0 pages.
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: INTEL Product ID: BKDG+ICH4 APIC at: 0xFEE00000
Processor #0 Pentium 4(tm) XEON(tm) APIC version 20
I/O APIC #1 Version 32 at 0xFEC00000.
Enabling APIC mode: Flat. Using 1 I/O APICs
Processors: 1
Kernel command line: BOOT_IMAGE=Knoppix ro root=302 hda=scsi hdb=scsi hdc=ide hdd=scsi hde=scsi hdf=scsi hdg=scsi hdh=scsi apm=power-off nomce
ide_setup: hda=scsi
ide_setup: hdb=scsi
ide_setup: hdc=ide -- BAD OPTION
ide_setup: hdd=scsi
ide_setup: hde=scsi
ide_setup: hdf=scsi
ide_setup: hdg=scsi
ide_setup: hdh=scsi
Initializing CPU#0
Detected 1699.823 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 3394.76 BogoMIPS
Memory: 247352k/253312k available (1262k kernel code, 5572k reserved, 534k data, 132k init, 0k highmem)
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 256K
CPU: Hyper-Threading is disabled
CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
CPU: Common caps: bfebfbff 00000000 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 256K
CPU: Hyper-Threading is disabled
CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
CPU: Common caps: bfebfbff 00000000 00000000 00000000
CPU0: Intel Mobile Intel(R) Celeron(R) CPU 1.70GHz stepping 07
per-CPU timeslice cutoff: 731.34 usecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Error: only one processor found.
ENABLING IO-APIC IRQs
Setting 1 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 1 ... ok.
init IO_APIC IRQs
..TIMER: vector=0x31 pin1=-1 pin2=0
...trying to set up timer (IRQ0) through the 8259A ...
..... (found pin 0) ...works.
number of MP IRQ sources: 33.
number of IO-APIC #1 registers: 24.
testing the IO APIC.......................
IO APIC #1......
.... register #00: 01000000
....... : physical APIC id: 01
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00178020
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0020
.... register #02: 00000000
....... : arbitration: 00
.... register #03: 00000001
....... : Boot DT : 1
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 001 01 0 0 0 0 0 1 1 31
01 001 01 0 0 0 0 0 1 1 39
02 000 00 1 0 0 0 0 0 0 00
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 001 01 0 0 0 0 0 1 1 51
06 001 01 0 0 0 0 0 1 1 59
07 001 01 0 0 0 0 0 1 1 61
08 001 01 0 0 0 0 0 1 1 69
09 001 01 0 0 0 0 0 1 1 71
0a 001 01 1 1 0 0 0 1 1 79
0b 001 01 1 1 0 0 0 1 1 81
0c 001 01 0 0 0 0 0 1 1 89
0d 001 01 0 0 0 0 0 1 1 91
0e 001 01 0 0 0 0 0 1 1 99
0f 001 01 0 0 0 0 0 1 1 A1
10 001 01 0 0 0 0 0 1 1 A9
11 001 01 0 0 0 0 0 1 1 B1
12 001 01 0 0 0 0 0 1 1 B9
13 001 01 0 0 0 0 0 1 1 C1
14 001 01 0 0 0 0 0 1 1 C9
15 001 01 0 0 0 0 0 1 1 D1
16 001 01 0 0 0 0 0 1 1 D9
17 001 01 0 0 0 0 0 1 1 E1
IRQ to pin mappings:
IRQ0 -> 0:0-> 0:0
IRQ1 -> 0:1
IRQ2 -> 0:2
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
IRQ20 -> 0:20
IRQ21 -> 0:21
IRQ22 -> 0:22
IRQ23 -> 0:23
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1699.7812 MHz.
..... host bus clock speed is 99.9870 MHz.
cpu: 0, clocks: 999870, slice: 499935
CPU0<T0:999856,T1:499920,D:1,S:499935,C:999870>
Waiting on wait_init_idle (map = 0x0)
All processors have done init_idle
PCI: PCI BIOS revision 2.10 entry at 0xfd824, last bus=2
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 00:1f.1
Transparent bridge - Intel Corp. 82801BA/CA/DB/EB PCI Bridge
PCI: Using IRQ router PIIX [8086/24c0] at 00:1f.0
PCI->APIC IRQ transform: (B0,I2,P0) -> 0
PCI->APIC IRQ transform: (B0,I29,P0) -> 0
PCI->APIC IRQ transform: (B0,I29,P1) -> 3
PCI->APIC IRQ transform: (B0,I29,P2) -> 0
PCI->APIC IRQ transform: (B0,I29,P3) -> 7
PCI->APIC IRQ transform: (B0,I31,P0) -> 1
PCI->APIC IRQ transform: (B0,I31,P1) -> 1
PCI->APIC IRQ transform: (B0,I31,P1) -> 1
PCI->APIC IRQ transform: (B0,I31,P1) -> 1
PCI->APIC IRQ transform: (B2,I5,P0) -> 3
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
vesafb: framebuffer at 0xd8000000, mapped to 0xd000d000, size 3072k
vesafb: mode is 1024x768x16, linelength=2048, pages=4
vesafb: protected mode interface info at a5f3:1f5f
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
pty: 256 Unix98 ptys configured
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 00:1f.1
PCI: Enabling device 00:1f.1 (0005 -> 0007)
ICH4: chipset revision 1
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1860-0x1867, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x1868-0x186f, BIOS settings: hdc:DMA, hdd:pio
hda: IC25N020ATCS04-0, ATA DISK drive
hdc: QSI DVD-ROM SDR-083, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 39070080 sectors (20004 MB) w/1768KiB Cache, CHS=2432/255/63
hdc: attached ide-cdrom driver.
hdc: ATAPI 24X DVD-ROM drive, 512kB Cache
Uniform CD-ROM driver Revision: 3.12
Partition check:
hda: hda1 hda2 hda3 < hda5 hda6 >
ide: late registration of driver.
Promise Fasttrak(tm) Softwareraid driver 0.03beta: No raid array found
Highpoint HPT370 Softwareraid driver for linux version 0.02
Guestimating sector 39069055 for superblock
driver for Silicon Image(tm) Medley(tm) hardware version 0.0.1: No raid array found
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 16384)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 168k freed
VFS: Mounted root (ext2 filesystem).
FAT: bogus logical sector size 38917
reiserfs: found format "3.6" with standard journal
reiserfs: checking transaction log (device ide0(3,2)) ...
for (ide0(3,2))
reiserfs: replayed 3 transactions in 0 seconds
ide0(3,2):Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Trying to move old root to /initrd ... okay
Freeing unused kernel memory: 132k freed
Adding Swap: 522072k swap-space (priority -1)
ide0(3,2):Removing [134378 134623 0x0 SD]..done
ide0(3,2):There were 1 uncompleted unlinks/truncates. Completed
Real Time Clock Driver v1.10e
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
PCI: No IRQ known for interrupt pin A of device 02:09.0. Probably buggy MP table.
Yenta IRQ list 00b8, PCI irq0
Socket status: 30000007
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 18:09:24 Sep 19 2003
usb-uhci.c: High bandwidth mode enabled
PCI: No IRQ known for interrupt pin A of device 00:1d.0. Probably buggy MP table.
usb-uhci.c: found UHCI device with no IRQ assigned. check BIOS settings!
PCI: Setting latency timer of device 00:1d.1 to 64
usb-uhci.c: USB UHCI at I/O 0x1820, IRQ 3
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: No IRQ known for interrupt pin C of device 00:1d.2. Probably buggy MP table.
usb-uhci.c: found UHCI device with no IRQ assigned. check BIOS settings!
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled
8139too Fast Ethernet driver 0.9.26
eth0: RealTek RTL8139 Fast Ethernet at 0xd0476000, 00:00:e2:99:b3:9b, IRQ 3
eth0: Identified 8139 chip type 'RTL-8139C'
NTFS driver v1.1.22 [Flags: R/W MODULE]
Journalled Block Device driver loaded
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 196M
agpgart: Detected an Intel(R) 845G Chipset.
agpgart: Detected 8060K stolen memory.
agpgart: AGP aperture is 128M @ 0xd8000000
[drm] AGP 0.99 aperture @ 0xd8000000 128MB
[drm] Initialized i830 1.3.2 20021108 on minor 0
ttyS0: LSR safety check engaged!
ttyS0: LSR safety check engaged!
ttyS1: LSR safety check engaged!
ttyS1: LSR safety check engaged!
eth0: Setting 100mbps full-duplex based on auto-negotiated partner ability 41e1.
blk: queue c0334960, I/O limit 4095Mb (mask 0xffffffff)
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0820-0x08ff: clean.
cs: IO port probe 0x0800-0x080f: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x378-0x37f 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
ALSA intel8x0.c:2471: unable to grab IRQ 1
Intel ICH soundcard not found or device busy
memory : cc4cee30
memory : cc4cedf0
memory : cc4cedb0
mtrr: base(0xd8020000) is not aligned on a size(0x180000) boundary
memory : cc4ced30
memory : cc4cecf0
memory : cc4cecb0
memory : cc4cec70
memory : cc4cec30
PCI: No IRQ known for interrupt pin A of device 00:02.0. Probably buggy MP table.
general protection fault: e7ac
i830 agpgart autofs4 af_packet ext3 jbd ntfs msdos nls_iso8859-1 nls_cp437 soundcore 8139too mii crc32 serial usb-uhci usbcore ds yenta_socket pcmcia_core apm rtc reiserfs
CPU: 0
EIP: 0050:[<000023b4>] Not tainted
EFLAGS: 00010046
eax: 00000246 ebx: 00000001 ecx: 00000000 edx: 00000000
esi: 000000ff edi: 00000014 ebp: c82a3ea0 esp: c82a3e98
ds: 0058 es: 0000 ss: 0018
Process kdeinit (pid: 380, stackpage=c82a3000)
Stack: 462744ac 00003ea0 00000058 00ff0246 3eb40050 00000001 530a0000 00000216
00484677 cf1d0000 ffffffff d042d126 00000010 ffffffff 00000246 00000018
00000018 c82a3f66 000000ff ffffffff ffffffff c7de3130 40f48016 ffffffff
Call Trace: [<d042d126>] [<d042d5d7>] [<d042efd1>] [<d042e268>] [<c015e98e>] [<c013c305>] [<c0108a57>]
Code: Bad EIP value.
ALSA intel8x0.c:2471: unable to grab IRQ 1
Intel ICH soundcard not found or device busy
Grazie mille per la disponibilita!
Ciao
Francesco
Reply to: