Attached is the kernel .config if anyone is courious...
I have an ISA 3com 3c509 nic in the EISA slot. (module loads fine for it to!
yay!)
Linux version 2.4.22-pa12-telephony (root@ldap.pcbkits.com) (gcc version
3.0.4) #1 Tue Oct 21 05:38:37 UTC 2003
FP[0] enabled: Rev 1 Model 15
The 32-bit Kernel has started...
Determining PDC firmware type: System Map.
model 00005010 00000481 00000000 02020202 7782df71 100000f0 00000004
000000ba 000000ba
vers 00000008
CPUID vers 15 rev 8 (0x000001e8)
model 9000/778/B132L
Total Memory: 96 Mb
pagetable_init
On node 0 totalpages: 24576
zone(0): 24576 pages.
zone(1): 0 pages.
zone(2): 0 pages.
LED display at f0190001 registered
Kernel command line: root=/dev/sda5 HOME=/ console=tty0 sti=8/24
sti_font=VGA8x16 TERM=linux palo_kernel=5/boot/vmlinux
Console: colour dummy device 160x64
Calibrating delay loop... 87.85 BogoMIPS
Memory: 94312k available
Dentry cache hash table entries: 16384 (order: 5, 131072 bytes)
Inode cache hash table entries: 8192 (order: 4, 65536 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
Searching for devices...
Found devices:
1. Dino PS/2 Port (10) at 0xfff81000 [1], versions 0x7, 0x0, 0x96
2. Phantom PseudoBC GSC+ Port (7) at 0xffc00000 [8], versions 0x504, 0x0,
0x0
3. Dino PCI Bridge (13) at 0xfff80000 [8/0], versions 0x680, 0x1, 0xa
4. Dino RS-232 (10) at 0xfff83000 [8/0/192], versions 0x7, 0x0, 0x8c
5. Merlin 132 Core BA (11) at 0xffd00000 [8/16], versions 0x3c, 0x0, 0x81,
additional addresses: 0xffd0c000 0xffc00000
6. Merlin 132 Core Centronics (10) at 0xffd02000 [8/16/0], versions 0x3c,
0x0, 0x74, additional addresses: 0xffd01000 0xffd03000
7. Merlin 132 Core Audio (10) at 0xffd04000 [8/16/1], versions 0x3c, 0x4,
0x7b
8. Merlin 132 Core RS-232 (10) at 0xffd05000 [8/16/4], versions 0x3c, 0x0,
0x8c
9. Merlin 132 Core SCSI (10) at 0xffd06000 [8/16/5], versions 0x3c, 0x0,
0x82
10. Merlin 132 Core LAN (802.3) (10) at 0xffd07000 [8/16/6], versions 0x3c,
0x0, 0x8a
11. Merlin 132 Core PS/2 Port (10) at 0xffd08000 [8/16/7], versions 0x3c,
0x0, 0x84
12. Merlin 132 Core PS/2 Port (10) at 0xffd08100 [8/16/8], versions 0x3c,
0x0, 0x84
13. Merlin 132 Wax BA (11) at 0xffe00000 [8/20], versions 0x40, 0x0, 0x8e
14. Raven Backplane Wax HIL (10) at 0xffe01000 [8/20/1], versions 0x17, 0x0,
0x73
15. Merlin 132 Wax RS-232 (10) at 0xffe02000 [8/20/2], versions 0x40, 0x0,
0x8c
16. Merlin 132 Wax EISA BA (11) at 0xfc000000 [8/20/5], versions 0x40, 0x0,
0x90, additional addresses: 0xf0184000
17. Gecko GSC Core Graphics (10) at 0xf8000000 [8/24], versions 0x16, 0x0,
0x85, additional addresses: 0xf0011000
18. Merlin L2 132 (9000/778/B132L) (0) at 0xfffbe000 [62], versions 0x501,
0x0, 0x4
19. Memory (1) at 0xfffbf000 [63], versions 0x60, 0x0, 0x9
CPU(s): 1 x PA7300LC (PCX-L2) at 132.000000 MHz
Lasi version 0 at 0xffd00000 found.
Wax at 0xffe00000 found.
Wax EISA Adapter found at 0xfc000000
EISA EEPROM at 0xf0184000
Enumerating EISA bus
EISA slot 1 a configured board was not detected ( expected ___FFFF)
Dino version 2.1 found at 0xfff80000
The GSCtoPCI (Dino hrev 1) bus converter found may exhibit
data corruption. See Service Note Numbers: A4190A-01, A4191A-01.
Systems shipped after Aug 20, 1997 will not exhibit this problem.
Models affected: C180, C160, C160L, B160L, and B132L workstations.
Dino: No PCI devices enabled.
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Soft power switch enabled, polling @ 0xf0140000.
Starting kswapd
Journalled Block Device driver loaded
parport_init_chip: initialize bidirectional-mode.
parport0: PC-style at 0xffd02800, irq 88 [PCSPP,TRISTATE]
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ
SERIAL_PCI enabled
ttyS00 at iomem 0xffd05800 (irq = 90) is a 16550A
ttyS01 at iomem 0xfff83800 (irq = 138) is a 16550A
ttyS02 at iomem 0xffe02800 (irq = 121) is a 16550A
PS/2 keyboard port at 0xffd08000 (irq 69) found, device attached.
PS/2 psaux port at 0xffd08100 (irq 69) found, no device attached.
lp0: using parport0 (interrupt-driven).
Generic RTC Driver v1.07
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
SCSI subsystem driver Revision: 1.00
53c700: Version 2.8 By James.Bottomley@HansenPartnership.com
scsi0: 53c710 rev 2
scsi0 : LASI SCSI 53c700
scsi0: (6:0) Synchronous at offset 8, period 100ns
Vendor: IBM Model: DORS-32160 Rev: HP02
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi disk sda at scsi0, channel 0, id 6, lun 0
scsi0: (6:0) Enabling Tag Command Queuing
SCSI device sda: 4194685 512-byte hdwr sectors (2148 MB)
Partition check:
sda: sda1 sda2 sda3 < sda5 sda6 sda7 sda8 sda9 sda10 >
Lasi Harmony Audio driver V0.9a, h/w id 20, rev. 9 at 0xffd04000, IRQ 82
STI GSC/PCI graphics driver version 0.9
STI word mode ROM at f0011000, hpa at f8000000
STI id 2d08c0a7-9a02587, conforms to spec rev. 8.07
STI device: INTERNAL_EG_640
sticon: Initializing STI text console.
Console: switching to colour STI console 80x30
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 8192 bind 16384)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
IPv6 v0.8 for NET4.0
IPv6 over IPv4 tunneling driver
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 238k freed
Adding Swap: 124616k swap-space (priority -1)
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,5), internal journal
ip_tables: (C) 2000-2002 Netfilter core team
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,6), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,7), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,8), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,9), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,10), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Humm, I think I'll wait on this kernel.
ldap:~# wget
ftp://ftp.de.debian.org/debian/pool/main/k/kernel-patch-2.4.21-hppa/kernel-image-2.4.21-32_pa7.3_hppa.deb
--17:05:31--
ftp://ftp.de.debian.org/debian/pool/main/k/kernel-patch-2.4.21-hppa/kernel-image-2.4.21-32_pa7.3_hppa.deb
=> `kernel-image-2.4.21-32_pa7.3_hppa.deb'
Resolving ftp.de.debian.org... done.
Connecting to ftp.de.debian.org[141.76.2.4]:21... connected.
Logging in as anonymous ... Logged in!
==> SYST ... done. ==> PWD ... done.
==> TYPE I ... done. ==> CWD /debian/pool/main/k/kernel-patch-2.4.21-hppa
... done.
==> PORT ... done. ==> RETR kernel-image-2.4.21-32_pa7.3_hppa.deb ...
done.
Length: 3,826,048 (unauthoritative)
100%[==============================>] 3,826,048 182.93K/s ETA 00:00
17:05:55 (182.93 KB/s) - `kernel-image-2.4.21-32_pa7.3_hppa.deb' saved
[3826048]
ldap:~# dpkg -i kernel-image-2.4.21-32_pa7.3_hppa.deb
Selecting previously deselected package kernel-image-2.4.21-32.
(Reading database ... 30148 files and directories currently installed.)
Unpacking kernel-image-2.4.21-32 (from
kernel-image-2.4.21-32_pa7.3_hppa.deb) ...
Setting up kernel-image-2.4.21-32 (pa7.3) ...
error reading /lib/modules/2.4.21-32/build :No such file or directory
Deleting /lib/modules/2.4.21-32/build
(some 200 lines suppressed, like the 3 below)
depmod: *** Unresolved symbols in
/lib/modules/2.4.21-32/kernel/net/sched/sch_sfq.o
depmod: *** Unresolved symbols in
/lib/modules/2.4.21-32/kernel/net/sched/sch_tbf.o
depmod: *** Unresolved symbols in
/lib/modules/2.4.21-32/kernel/net/sched/sch_teql.o
There was a problem running depmod. This may be benign,
(You may have versioned symbol names, for instance).
Or this could be an error.
depmod exited with return value 1
In any case, since depmod is run at install time,
we could just defer running depmod
Would you like to abort now? [Yes]
Strange, I'm not using versioned module symbols...
[*] Enable loadable module support
[ ] Set version information on all module symbols
[*] Kernel module loader
----- Original Message -----
From: "Joel Soete" <joel.soete@tiscali.be>
To: "Scott Edwards" <debian-hppa@pcbkits.com>
Cc: <debian-hppa@lists.debian.org>
Sent: Saturday, October 25, 2003 9:11 AM
Subject: Re: Serial Ports do not communicate, on a B132L with a 2.4.22-pa12
kernel
> Hi Scott
>
> Scott Edwards wrote:
> [...]
>
> >Serial snippet from dmesg:
> >Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ
> >SERIAL_PCI enabled
> >ttyS00 at iomem 0xffd05800 (irq = 90) is a 16550A
> >ttyS01 at iomem 0xfff83800 (irq = 138) is a 16550A
> >ttyS02 at iomem 0xffe02800 (irq = 121) is a 16550A
> >
> >
> >
> Very strange, that is about 3 years that boot b132 and b180 and I don't
> remember this (always discover 2 ttyS0[01])
> Do you have some additional pci card?
>
> Could you retry with a dpkg compiled kernel image (eg:
>
ftp.de.debian.org/debian/pool/main/k/kernel-patch-2.4.21-hppa/kernel-image-2
.4.21-32_pa7.3_hppa.deb)
>
> hth,
> Joel
>
Attachment:
config-linux-2.4.22-pa12-telephony
Description: Binary data