Re: primary <-> secondary et boute.
vla un lilo.conf qui permet de laisser windows sur le 2eme disk
On Fri, Feb 02, 2001 at 05:55:46PM +0000, Bruno Durning wrote:
> Bonjour à tous,
>
> Note: si quelque connaît un truc pour installer 98 sur un secondary master je suis aussi preneur; ou alors un moyen de lire et écrire des .doc (97 et 2000 assez évolués avec des schémas et tout).
> Je serais bien rester avec ma seule patate mais parler de lyx à des personnes que le terme ligne de commande fait peur et rappel le moyen-age; et ben c'est pas gagner. Ne leur parler surtout pas de latex ils vous prendraient pour un fou...
>
> Bruno.
>
>
> --
> To UNSUBSCRIBE, email to debian-french-request@lists.debian.org
> with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
--
-------------------------------------
Paris jean-francois \|/ ____ \|/
paris.jean-francois@bigfoot.com "@' / ,. \ `@"
/_| \__/ |_\
jean-francois.paris@insa-lyon.fr \__U_/
^^^^^^^^^^^^^^^^^^^^^^^^
CLE PUBLIQUE PGP&GPG
DH/DSS ID: 0x403A1E7A RSA ID: 0xA1243647
-----------
ICQ #29259447
AIM mjediyoda
Jabber mjediyoda@jabber.org
-----------
PAGE WEB : http://www.chez.com/mjediyoda
-------------------------------------
#restricted
#password=c6Tfou
timeout=40
# /etc/lilo.conf - See: `lilo(8)' and `lilo.conf(5)',
# --------------- `install-mbr(8)', `/usr/share/doc/lilo/',
# and `/usr/share/doc/mbr/'.
# +---------------------------------------------------------------+
# | !! Reminder !! |
# | |
# | Don't forget to run `lilo' after you make changes to this |
# | conffile, `/boot/bootmess.txt', or install a new kernel. The |
# | computer will most likely fail to boot if a kernel-image |
# | post-install script or you don't remember to run `lilo'. |
# | |
# +---------------------------------------------------------------+
# Support LBA for large hard disks.
#
lba32
# Specifies the boot device. This is where Lilo installs its boot
# block. It can be either a partition, or the raw device, in which
# case it installs in the MBR, and will overwrite the current MBR.
#
boot=/dev/hda
# Specifies the device that should be mounted as root. (`/')
#
root=/dev/hda3
# Enable map compaction:
# Tries to merge read requests for adjacent sectors into a single
# read request. This drastically reduces load time and keeps the
# map smaller. Using `compact' is especially recommended when
# booting from a floppy disk. It is disabled here by default
# because it doesn't always work.
#
# compact
# Installs the specified file as the new boot sector
#
#install=/boot/boot.b
# Specifies the location of the map file
#
map=/boot/map
# You can set a password here, and uncomment the `restricted' lines
# in the image definitions below to make it so that a password must
# be typed to boot anything but a default configuration. If a
# command line is given, other than one specified by an `append'
# statement in `lilo.conf', the password will be required, but a
# standard default boot will not require one.
#
# This will, for instance, prevent anyone with access to the
# console from booting with something like `Linux init=/bin/sh',
# and thus becoming `root' without proper authorization.
#
# Note that if you really need this type of security, you will
# likely also want to use `install-mbr' to reconfigure the MBR
# program, as well as set up your BIOS to disallow booting from
# removable disk or CD-ROM, then put a password on getting into the
# BIOS configuration as well. Please RTFM `install-mbr(8)'.
#
# password=tatercounter2000
# Specifies the number of deciseconds (0.1 seconds) LILO should
# wait before booting the first image.
#
delay=200
# You can put a customized boot message up if you like. If you use
# `prompt', and this computer may need to reboot unattended, you
# must specify a `timeout', or it will sit there forever waiting
# for a keypress. `single-key' goes with the `alias' lines in the
# `image' configurations below. eg: You can press `1' to boot
# `Linux', `2' to boot `LinuxOLD', if you uncomment the `alias'.
#
# message=/boot/bootmess.txt
# prompt
# single-key
# delay=100
# timeout=100
# Specifies the VGA text mode at boot time. (normal, extended, ask, <mode>)
#
# vga=ask
# vga=9
#
vga=normal
# Kernel command line options that apply to all installed images go
# here. See: The `boot-prompt-HOWO' and `kernel-parameters.txt' in
# the Linux kernel `Documentation' directory.
#
# append=""
# Boot up Linux by default.
#
#prompt
default=linux
image=/boot/vmlinuz-2.4.0
label=linux
append="mem=320M"
vga=0x301
read-only
# restricted
# alias=1
image=/boot/vmlinuz-2.2.17
append="mem=320M"
label=failsafe
read-only
optional
# restricted
# alias=2
# If you have another OS on this machine to boot, you can uncomment the
# following lines, changing the device name on the `other' line to
# where your other OS' partition is.
#
# other=/dev/hda4
# label=HURD
# restricted
# alias=3
other=/dev/hdb1
label=dos
table=/dev/hdb
map-drive=0x81
to=0x80
map-drive=0x80
to=0x81
image=/boot/vmlinuz-2.2.17
label=bouh
append="mem=320M"
root=/dev/hdc7
read-only
Reply to: