Re: Weekly build for AMD64 Wheezy stalls
Update time.
I have been able to successfully install from the latest weekly build DVD iso using "Expert Install" and skipping the detect network hardware and set up network steps.
So issue with default install appears to be the failure when detecting network hardware where the firmware isn't present.
Relevant log details below:
Aug 1 02:54:31 main-menu[348]: INFO: Menu item 'ethdetect' selected
Aug 1 02:54:32 kernel: [ 30.498348] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
Aug 1 02:54:32 kernel: [ 30.498377] r8169 0000:03:00.0: enabling device (0001 -> 0003)
Aug 1 02:54:32 kernel: [ 30.498633] ACPI: PCI Interrupt Link [LN3A] enabled at IRQ 19
Aug 1 02:54:32 kernel: [ 30.498651] r8169 0000:03:00.0: PCI INT A -> Link[LN3A] -> GSI 19 (level, low) -> IRQ 19
Aug 1 02:54:32 kernel: [ 30.498692] r8169 0000:03:00.0: setting latency timer to 64
Aug 1 02:54:32 kernel: [ 30.498744] r8169 0000:03:00.0: irq 41 for MSI/MSI-X
Aug 1 02:54:32 kernel: [ 30.499242] r8169 0000:03:00.0: eth0: RTL8168d/8111d at 0xffffc90000660000, 48:5b:39:08:3e:6f, XID 083000c0 IRQ 41
Aug 1 02:54:32 kernel: [ 30.499247] r8169 0000:03:00.0: eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
Aug 1 02:54:32 kernel: [ 30.511223] cfg80211: Calling CRDA to update world regulatory domain
Aug 1 02:54:32 net/hw-detect.hotplug: Detected hotpluggable network interface eth0
Aug 1 02:54:32 kernel: [ 30.522107] ACPI: PCI Interrupt Link [LN4A] enabled at IRQ 18
Aug 1 02:54:32 kernel: [ 30.522128] ath9k 0000:04:00.0: PCI INT A -> Link[LN4A] -> GSI 18 (level, low) -> IRQ 18
Aug 1 02:54:32 kernel: [ 30.522138] ath9k 0000:04:00.0: setting latency timer to 64
Aug 1 02:54:32 net/hw-detect.hotplug: Detected hotpluggable network interface lo
Aug 1 02:54:32 kernel: [ 30.572369] ath: EEPROM regdomain: 0x60
Aug 1 02:54:32 kernel: [ 30.572373] ath: EEPROM indicates we should expect a direct regpair map
Aug 1 02:54:32 kernel: [ 30.572378] ath: Country alpha2 being used: 00
Aug 1 02:54:32 kernel: [ 30.572379] ath: Regpair used: 0x60
Aug 1 02:54:32 kernel: [ 30.578841] ieee80211 phy0: Selected rate control algorithm 'ath9k_rate_control'
Aug 1 02:54:32 kernel: [ 30.579428] Registered led device: ath9k-phy0
Aug 1 02:54:32 kernel: [ 30.579439] ieee80211 phy0: Atheros AR9285 Rev:2 mem=0xffffc900030a0000, irq=18
Aug 1 02:54:32 net/hw-detect.hotplug: Detected hotpluggable network interface wlan0
Aug 1 02:54:34 check-missing-firmware: /dev/.udev/firmware-missing does not exist, skipping
Aug 1 02:54:34 check-missing-firmware: /run/udev/firmware-missing does not exist, skipping
Aug 1 02:54:34 check-missing-firmware: no missing firmware in /dev/.udev/firmware-missing /run/udev/firmware-missing
Aug 1 02:54:34 kernel: [ 32.830478] ADDRCONF(NETDEV_UP): wlan0: link is not ready
Aug 1 02:54:34 kernel: [ 32.868460] r8169 0000:03:00.0: eth0: unable to load firmware patch rtl_nic/rtl8168d-2.fw (-2)
Aug 1 02:54:34 kernel: [ 32.875472] r8169 0000:03:00.0: eth0: link down
Aug 1 02:54:34 kernel: [ 32.876079] ADDRCONF(NETDEV_UP): eth0: link is not ready
Aug 1 02:54:35 check-missing-firmware: /dev/.udev/firmware-missing does not exist, skipping
Aug 1 02:54:35 check-missing-firmware: missing firmware files (rtl_nic/rtl8168d-2.fw) for r8169
Reply to: