Bug#947449: installation-report: No networking on Olimex Lime2 (Allwinner A20)
Hello,
Samuel Thibault kirjoitti 27.12.2019 klo 9.42:
> Possible the board needs some non-free firmware?
> Did you try to install firmware-linux-free?
Yes, firmware-linux-free was apparently installed during the base install.
> Also, please post how the network board is detected (e.g. the complete
> dmesg output).
See dmesg_install.out for the dmesg output obtained at the end of
installation and dmesg_postinstall.out for the output of dmesg in the
installed system. It seems the system does not attempt to bring eth0 up
during the boot; the following lines appear only after manually running
ip link set eth0 up (with ethernet cable connected):
[ 671.988940] Micrel KSZ9031 Gigabit PHY stmmac-0:01: attached PHY
driver [Micrel KSZ9031 Gigabit PHY] (mii_bus:phy_addr=stmmac-0:01, irq=POLL)
[ 671.992969] sun7i-dwmac 1c50000.ethernet eth0: No Safety Features
support found
[ 671.992989] sun7i-dwmac 1c50000.ethernet eth0: RX IPC Checksum
Offload disabled
[ 671.993003] sun7i-dwmac 1c50000.ethernet eth0: No MAC Management
Counters available
[ 671.993013] sun7i-dwmac 1c50000.ethernet eth0: PTP not supported by HW
[ 671.993972] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 674.023384] sun7i-dwmac 1c50000.ethernet eth0: Link is Up -
100Mbps/Full - flow control rx/tx
[ 674.023444] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Then I get the Link is down / up messages correctly after the cable is
disconnected / connected, but the network does not work nevertheless
(dhclient does not get any response; I didn't try wireshark on the other
end of the cable with the installed system, but I assume it's the same
as with the installer).
Marek
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.19.0-6-armmp (debian-kernel@lists.debian.org) (gcc version 8.3.0 (Debian 8.3.0-6)) #1 SMP Debian 4.19.67-2+deb10u1 (2019-09-20)
[ 0.000000] CPU: ARMv7 Processor [410fc074] revision 4 (ARMv7), cr=10c5387d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: Olimex A20-OLinuXino-LIME2
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] efi: Getting EFI parameters from FDT:
[ 0.000000] efi: UEFI not found.
[ 0.000000] cma: Reserved 16 MiB at 0x7e000000
[ 0.000000] On node 0 totalpages: 259894
[ 0.000000] Normal zone: 1728 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 196608 pages, LIFO batch:63
[ 0.000000] HighMem zone: 63286 pages, LIFO batch:15
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: Using PSCI v0.1 Function IDs from DT
[ 0.000000] random: get_random_bytes called from start_kernel+0xa0/0x504 with crng_init=0
[ 0.000000] percpu: Embedded 17 pages/cpu s39756 r8192 d21684 u69632
[ 0.000000] pcpu-alloc: s39756 r8192 d21684 u69632 alloc=17*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258166
[ 0.000000] Kernel command line: console=ttyS0,115200
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 980120K/1039576K available (9216K kernel code, 1113K rwdata, 2588K rodata, 2048K init, 310K bss, 43072K reserved, 16384K cma-reserved, 236760K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (10208 kB)
[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB)
[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1113 kB)
[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 311 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] ftrace: allocating 32722 entries in 96 pages
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] GIC: Using split EOI/Deactivate mode
[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000009] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.000024] Switching to timer-based delay loop, resolution 41ns
[ 0.001596] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[ 0.002595] clocksource: hstimer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370868154 ns
[ 0.003365] Console: colour dummy device 80x30
[ 0.003447] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[ 0.003465] pid_max: default: 32768 minimum: 301
[ 0.003732] Security Framework initialized
[ 0.003749] Yama: disabled by default; enable with sysctl kernel.yama.*
[ 0.004001] AppArmor: AppArmor initialized
[ 0.004120] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.004138] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.005384] CPU: Testing write buffer coherency: ok
[ 0.005967] /cpus/cpu@0 missing clock-frequency property
[ 0.005995] /cpus/cpu@1 missing clock-frequency property
[ 0.006013] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.006882] Setting up static identity map for 0x40300000 - 0x403000a0
[ 0.008430] rcu: Hierarchical SRCU implementation.
[ 0.012414] EFI services will not be available.
[ 0.013085] smp: Bringing up secondary CPUs ...
[ 0.024173] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.024430] smp: Brought up 1 node, 2 CPUs
[ 0.024453] SMP: Total of 2 processors activated (96.00 BogoMIPS).
[ 0.024460] CPU: All CPU(s) started in HYP mode.
[ 0.024466] CPU: Virtualization extensions available.
[ 0.025815] devtmpfs: initialized
[ 0.034716] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 4
[ 0.035166] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.035198] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.036732] pinctrl core: initialized pinctrl subsystem
[ 0.038402] DMI not present or invalid.
[ 0.038963] NET: Registered protocol family 16
[ 0.041319] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.042442] audit: initializing netlink subsys (disabled)
[ 0.042890] audit: type=2000 audit(0.032:1): state=initialized audit_enabled=0 res=1
[ 0.044782] No ATAGs?
[ 0.044956] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.044973] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.046138] Serial: AMBA PL011 UART driver
[ 0.073064] vgaarb: loaded
[ 0.074302] media: Linux media interface: v0.10
[ 0.074358] videodev: Linux video capture interface: v2.00
[ 0.074428] pps_core: LinuxPPS API ver. 1 registered
[ 0.074438] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.074464] PTP clock support registered
[ 0.076884] clocksource: Switched to clocksource arch_sys_counter
[ 0.156414] VFS: Disk quotas dquot_6.6.0
[ 0.156541] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.157384] AppArmor: AppArmor Filesystem Enabled
[ 0.158624] simple-framebuffer 7f736000.framebuffer: framebuffer at 0x7f736000, 0x8ca000 bytes, mapped to 0x(ptrval)
[ 0.158647] simple-framebuffer 7f736000.framebuffer: format=x8r8g8b8, mode=1920x1200x32, linelength=7680
[ 0.199775] Console: switching to colour frame buffer device 240x75
[ 0.239834] simple-framebuffer 7f736000.framebuffer: fb0: simplefb registered!
[ 0.253218] NET: Registered protocol family 2
[ 0.254312] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)
[ 0.254356] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.254442] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.254570] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.254751] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.254825] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.255313] NET: Registered protocol family 1
[ 0.255360] NET: Registered protocol family 44
[ 0.255378] PCI: CLS 0 bytes, default 64
[ 0.256037] Unpacking initramfs...
[ 1.639606] Freeing initrd memory: 16088K
[ 1.640193] hw perfevents: no interrupt-affinity property for /pmu, guessing.
[ 1.640529] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
[ 1.643562] Initialise system trusted keyrings
[ 1.643647] Key type blacklist registered
[ 1.644058] workingset: timestamp_bits=14 max_order=18 bucket_order=4
[ 1.651592] zbud: loaded
[ 5.788442] Key type asymmetric registered
[ 5.788470] Asymmetric key parser 'x509' registered
[ 5.788546] bounce: pool size: 64 pages
[ 5.788665] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[ 5.789052] io scheduler noop registered
[ 5.789070] io scheduler deadline registered
[ 5.789360] io scheduler cfq registered (default)
[ 5.789374] io scheduler mq-deadline registered
[ 5.796652] sun4i-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver
[ 5.815328] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 5.818648] console [ttyS0] disabled
[ 5.839007] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 45, base_baud = 1500000) is a U6_16550A
[ 6.555474] console [ttyS0] enabled
[ 6.560307] Serial: AMBA driver
[ 6.567618] libphy: Fixed MDIO Bus: probed
[ 6.572910] mousedev: PS/2 mouse device common for all mice
[ 6.581217] sunxi-rtc 1c20d00.rtc: registered as rtc0
[ 6.586317] sunxi-rtc 1c20d00.rtc: RTC enabled
[ 6.593953] ledtrig-cpu: registered to indicate activity on CPUs
[ 6.602145] NET: Registered protocol family 10
[ 6.640502] Segment Routing with IPv6
[ 6.644456] mip6: Mobile IPv6
[ 6.647532] NET: Registered protocol family 17
[ 6.652323] mpls_gso: MPLS GSO support
[ 6.656195] ThumbEE CPU extension supported.
[ 6.660502] Registering SWP/SWPB emulation handler
[ 6.666383] registered taskstats version 1
[ 6.670539] Loading compiled-in X.509 certificates
[ 7.034543] Loaded X.509 cert 'Debian Secure Boot CA: 6ccece7e4c6c0d1f6149f3dd27dfcc5cbb419ea1'
[ 7.043426] Loaded X.509 cert 'Debian Secure Boot Signer: 00a7468def'
[ 7.050100] zswap: loaded using pool lzo/zbud
[ 7.054792] AppArmor: AppArmor sha1 policy hashing enabled
[ 7.076733] sunxi-rtc 1c20d00.rtc: setting system clock to 1970-01-01 00:00:16 UTC (16)
[ 7.084851] sr_init: No PMIC hook to init smartreflex
[ 7.090706] vcc3v0: disabling
[ 7.093734] vcc3v3: disabling
[ 7.096705] vcc5v0: disabling
[ 7.099694] ahci-5v: disabling
[ 7.102771] usb0-vbus: disabling
[ 7.106018] usb1-vbus: disabling
[ 7.109265] usb2-vbus: disabling
[ 7.127767] Freeing unused kernel memory: 2048K
[ 7.133184] Run /init as init process
[ 7.614961] sunxi-mmc 1c0f000.mmc: Linked as a consumer to regulator.2
[ 7.623423] sunxi-mmc 1c0f000.mmc: Got CD GPIO
[ 7.642288] sun4i-usb-phy 1c13400.phy: Linked as a consumer to regulator.6
[ 7.677265] sunxi-mmc 1c0f000.mmc: initialized, max. request size: 16384 KB
[ 7.698891] usbcore: registered new interface driver usbfs
[ 7.710629] sun4i-usb-phy 1c13400.phy: Linked as a consumer to regulator.7
[ 7.711814] SCSI subsystem initialized
[ 7.721335] usbcore: registered new interface driver hub
[ 7.722911] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
[ 7.727326] sun4i-usb-phy 1c13400.phy: Linked as a consumer to regulator.8
[ 7.752507] axp20x-i2c 0-0034: AXP20x variant AXP209 found
[ 7.760669] mmc0: host does not support reading read-only switch, assuming write-enable
[ 7.760830] usbcore: registered new device driver usb
[ 7.786100] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 7.802365] mmc0: new high speed SDHC card at address aaaa
[ 7.810229] ehci-platform: EHCI generic platform driver
[ 7.811866] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 7.823243] axp20x-i2c 0-0034: AXP20X driver loaded
[ 7.831522] mmcblk0: mmc0:aaaa SC16G 14.8 GiB
[ 7.838046] ehci-platform 1c14000.usb: EHCI Host Controller
[ 7.847321] ohci-platform: OHCI generic platform driver
[ 7.855747] ohci-platform 1c14400.usb: Generic Platform OHCI controller
[ 7.857892] usb_phy_generic usb_phy_generic.0.auto: usb_phy_generic.0.auto supply vcc not found, using dummy regulator
[ 7.873004] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 1
[ 7.878241] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 2
[ 7.889303] mmcblk0: p1
[ 7.893483] libata version 3.00 loaded.
[ 7.895278] ohci-platform 1c14400.usb: irq 32, io mem 0x01c14400
[ 7.900780] ahci-sunxi 1c18000.sata: Linked as a consumer to regulator.5
[ 7.913781] ehci-platform 1c14000.usb: irq 31, io mem 0x01c14000
[ 7.927632] usb_phy_generic usb_phy_generic.0.auto: Linked as a consumer to regulator.0
[ 7.938185] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver
[ 7.945433] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 3
[ 7.945735] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00
[ 7.953660] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[ 7.967891] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 7.975181] usb usb3: Product: MUSB HDRC host driver
[ 7.980245] usb usb3: Manufacturer: Linux 4.19.0-6-armmp musb-hcd
[ 7.981077] ahci-sunxi 1c18000.sata: controller can't do PMP, turning off CAP_PMP
[ 7.986368] usb usb3: SerialNumber: musb-hdrc.1.auto
[ 7.992434] hub 3-0:1.0: USB hub found
[ 7.993917] ahci-sunxi 1c18000.sata: forcing PORTS_IMPL to 0x1
[ 8.010319] hub 3-0:1.0: 1 port detected
[ 8.014442] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode
[ 8.015601] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19
[ 8.023500] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc
[ 8.031764] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.047122] usb usb1: Product: Generic Platform OHCI controller
[ 8.053086] usb usb1: Manufacturer: Linux 4.19.0-6-armmp ohci_hcd
[ 8.059240] usb usb1: SerialNumber: 1c14400.usb
[ 8.090302] hub 1-0:1.0: USB hub found
[ 8.097192] hub 1-0:1.0: 1 port detected
[ 8.110325] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[ 8.110371] ohci-platform 1c1c400.usb: Generic Platform OHCI controller
[ 8.118698] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.118709] usb usb2: Product: EHCI Host Controller
[ 8.137664] usb usb2: Manufacturer: Linux 4.19.0-6-armmp ehci_hcd
[ 8.143855] usb usb2: SerialNumber: 1c14000.usb
[ 8.173420] hub 2-0:1.0: USB hub found
[ 8.177400] scsi host0: ahci-sunxi
[ 8.183449] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 35
[ 8.191790] hub 2-0:1.0: 1 port detected
[ 8.197059] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 4
[ 8.205464] ehci-platform 1c1c000.usb: EHCI Host Controller
[ 8.211894] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 5
[ 8.221478] ohci-platform 1c1c400.usb: irq 37, io mem 0x01c1c400
[ 8.228698] ehci-platform 1c1c000.usb: irq 36, io mem 0x01c1c000
[ 8.249061] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00
[ 8.255820] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[ 8.264247] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.271544] usb usb5: Product: EHCI Host Controller
[ 8.276513] usb usb5: Manufacturer: Linux 4.19.0-6-armmp ehci_hcd
[ 8.282666] usb usb5: SerialNumber: 1c1c000.usb
[ 8.286856] axp20x-usb-power-supply axp20x-usb-power-supply: DMA mask not set
[ 8.287436] ldo1: supplied by regulator-dummy
[ 8.303939] ldo2: supplied by regulator-dummy
[ 8.310225] ldo3: supplied by regulator-dummy
[ 8.315151] hub 5-0:1.0: USB hub found
[ 8.319695] ldo4: supplied by regulator-dummy
[ 8.324358] hub 5-0:1.0: 1 port detected
[ 8.328780] vddio-csi1: Bringing 3300000uV into 2800000-2800000uV
[ 8.336589] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19
[ 8.344996] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.352358] usb usb4: Product: Generic Platform OHCI controller
[ 8.358335] usb usb4: Manufacturer: Linux 4.19.0-6-armmp ohci_hcd
[ 8.364494] usb usb4: SerialNumber: 1c1c400.usb
[ 8.371346] ldo5: supplied by regulator-dummy
[ 8.377424] hub 4-0:1.0: USB hub found
[ 8.381927] dcdc2: supplied by regulator-dummy
[ 8.386740] hub 4-0:1.0: 1 port detected
[ 8.391463] dcdc3: supplied by regulator-dummy
[ 8.509167] ata1: SATA link down (SStatus 0 SControl 300)
[ 8.540934] usb 2-1: new high-speed USB device number 2 using ehci-platform
[ 8.716084] random: fast init done
[ 8.719546] usb 2-1: New USB device found, idVendor=0bda, idProduct=0316, bcdDevice= 2.04
[ 8.727750] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 8.734899] usb 2-1: Product: USB3.0-CRW
[ 8.738840] usb 2-1: Manufacturer: Generic
[ 8.742949] usb 2-1: SerialNumber: 20120501030900000
[ 8.773813] usb-storage 2-1:1.0: USB Mass Storage device detected
[ 8.781594] scsi host1: usb-storage 2-1:1.0
[ 8.788208] usbcore: registered new interface driver usb-storage
[ 8.798449] usbcore: registered new interface driver uas
[ 9.799834] scsi 1:0:0:0: Direct-Access Generic- SD/MMC 1.00 PQ: 0 ANSI: 4
[ 10.558595] sd 1:0:0:0: [sda] 7812096 512-byte logical blocks: (4.00 GB/3.72 GiB)
[ 10.559604] sd 1:0:0:0: [sda] Write Protect is off
[ 10.559622] sd 1:0:0:0: [sda] Mode Sense: 2f 00 00 00
[ 10.561065] sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 10.570294] sda: sda1 sda2 sda3
[ 10.577993] sd 1:0:0:0: [sda] Attached SCSI removable disk
[ 12.367165] random: crng init done
[ 26.210395] loop: module loaded
[ 26.240830] device-mapper: uevent: version 1.0.3
[ 26.243733] device-mapper: ioctl: 4.39.0-ioctl (2018-04-03) initialised: dm-devel@redhat.com
[ 29.560513] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 29.572644] ISO 9660 Extensions: RRIP_1991A
[ 29.773282] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 29.774788] ISO 9660 Extensions: RRIP_1991A
[ 30.081806] EXT4-fs (sda3): mounting ext2 file system using the ext4 subsystem
[ 30.093651] EXT4-fs (sda3): mounted filesystem without journal. Opts: (null)
[ 30.202344] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 30.203522] ISO 9660 Extensions: RRIP_1991A
[ 30.437720] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 30.444455] ISO 9660 Extensions: RRIP_1991A
[ 30.611568] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 30.617226] ISO 9660 Extensions: RRIP_1991A
[ 34.121798] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 34.123788] ISO 9660 Extensions: RRIP_1991A
[ 34.325646] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 34.327002] ISO 9660 Extensions: RRIP_1991A
[ 34.540510] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 34.542023] ISO 9660 Extensions: RRIP_1991A
[ 49.371799] EXT4-fs (sda3): mounting ext2 file system using the ext4 subsystem
[ 49.382647] EXT4-fs (sda3): mounted filesystem without journal. Opts: (null)
[ 49.455428] EXT4-fs (sda3): mounting ext2 file system using the ext4 subsystem
[ 49.466726] EXT4-fs (sda3): mounted filesystem without journal. Opts: (null)
[ 49.541722] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 49.547260] ISO 9660 Extensions: RRIP_1991A
[ 49.813594] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 49.818716] ISO 9660 Extensions: RRIP_1991A
[ 50.007100] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 50.012705] ISO 9660 Extensions: RRIP_1991A
[ 59.021810] EXT4-fs (sda3): mounting ext2 file system using the ext4 subsystem
[ 59.033184] EXT4-fs (sda3): mounted filesystem without journal. Opts: (null)
[ 59.081628] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 59.087948] ISO 9660 Extensions: RRIP_1991A
[ 130.574044] sun7i-dwmac 1c50000.ethernet: PTP uses main clock
[ 130.574071] sun7i-dwmac 1c50000.ethernet: no reset control found
[ 130.574139] sun7i-dwmac 1c50000.ethernet: no regulator found
[ 130.579193] sun7i-dwmac 1c50000.ethernet: Version ID not available
[ 130.579218] sun7i-dwmac 1c50000.ethernet: DWMAC1000
[ 130.579230] sun7i-dwmac 1c50000.ethernet: DMA HW capability register supported
[ 130.579238] sun7i-dwmac 1c50000.ethernet: Normal descriptors
[ 130.579245] sun7i-dwmac 1c50000.ethernet: Ring mode enabled
[ 130.614299] libphy: stmmac: probed
[ 130.614334] Micrel KSZ9031 Gigabit PHY stmmac-0:01: attached PHY driver [Micrel KSZ9031 Gigabit PHY] (mii_bus:phy_addr=stmmac-0:01, irq=POLL)
[ 134.855343] Micrel KSZ9031 Gigabit PHY stmmac-0:01: attached PHY driver [Micrel KSZ9031 Gigabit PHY] (mii_bus:phy_addr=stmmac-0:01, irq=POLL)
[ 134.858330] sun7i-dwmac 1c50000.ethernet eth0: No Safety Features support found
[ 134.858348] sun7i-dwmac 1c50000.ethernet eth0: RX IPC Checksum Offload disabled
[ 134.858362] sun7i-dwmac 1c50000.ethernet eth0: No MAC Management Counters available
[ 134.858371] sun7i-dwmac 1c50000.ethernet eth0: PTP not supported by HW
[ 134.859201] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 138.491344] Micrel KSZ9031 Gigabit PHY stmmac-0:01: attached PHY driver [Micrel KSZ9031 Gigabit PHY] (mii_bus:phy_addr=stmmac-0:01, irq=POLL)
[ 138.494285] sun7i-dwmac 1c50000.ethernet eth0: No Safety Features support found
[ 138.494304] sun7i-dwmac 1c50000.ethernet eth0: RX IPC Checksum Offload disabled
[ 138.494317] sun7i-dwmac 1c50000.ethernet eth0: No MAC Management Counters available
[ 138.494326] sun7i-dwmac 1c50000.ethernet eth0: PTP not supported by HW
[ 138.494701] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 142.598048] sun7i-dwmac 1c50000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx
[ 142.598127] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 251.365265] fuse init (API version 7.27)
[ 251.540975] raid6: int32x1 gen() 155 MB/s
[ 251.608957] raid6: int32x1 xor() 145 MB/s
[ 251.676967] raid6: int32x2 gen() 190 MB/s
[ 251.745017] raid6: int32x2 xor() 152 MB/s
[ 251.813192] raid6: int32x4 gen() 184 MB/s
[ 251.880943] raid6: int32x4 xor() 152 MB/s
[ 251.948882] raid6: int32x8 gen() 186 MB/s
[ 252.016954] raid6: int32x8 xor() 126 MB/s
[ 252.016963] raid6: using algorithm int32x2 gen() 190 MB/s
[ 252.016967] raid6: .... xor() 152 MB/s, rmw enabled
[ 252.016972] raid6: using intx1 recovery algorithm
[ 252.033615] xor: measuring software checksum speed
[ 252.072877] arm4regs : 1128.000 MB/sec
[ 252.112868] 8regs : 786.000 MB/sec
[ 252.152866] 32regs : 763.000 MB/sec
[ 252.152875] xor: using function: arm4regs (1128.000 MB/sec)
[ 252.252415] Btrfs loaded, crc32c=crc32c-generic
[ 252.391543] JFS: nTxBlock = 7926, nTxLock = 63415
[ 388.364131] Adding 989180k swap on /dev/mmcblk0p5. Priority:-2 extents:1 across:989180k SSFS
[ 396.177914] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: errors=remount-ro
[ 396.209611] EXT4-fs (mmcblk0p1): mounting ext2 file system using the ext4 subsystem
[ 396.218811] EXT4-fs (mmcblk0p1): mounted filesystem without journal. Opts: (null)
[ 1324.433922] EXT4-fs (sda3): mounting ext2 file system using the ext4 subsystem
[ 1324.446230] EXT4-fs (sda3): mounted filesystem without journal. Opts: (null)
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.19.0-6-armmp-lpae (debian-kernel@lists.debian.org) (gcc version 8.3.0 (Debian 8.3.0-6)) #1 SMP Debian 4.19.67-2+deb10u1 (2019-09-20)
[ 0.000000] CPU: ARMv7 Processor [410fc074] revision 4 (ARMv7), cr=30c5387d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: Olimex A20-OLinuXino-LIME2
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] efi: Getting EFI parameters from FDT:
[ 0.000000] efi: UEFI not found.
[ 0.000000] cma: Reserved 16 MiB at 0x000000007e000000
[ 0.000000] On node 0 totalpages: 259894
[ 0.000000] DMA zone: 1728 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 196608 pages, LIFO batch:63
[ 0.000000] HighMem zone: 63286 pages, LIFO batch:15
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: Using PSCI v0.1 Function IDs from DT
[ 0.000000] random: get_random_bytes called from start_kernel+0x9c/0x528 with crng_init=0
[ 0.000000] percpu: Embedded 17 pages/cpu s40396 r8192 d21044 u69632
[ 0.000000] pcpu-alloc: s40396 r8192 d21044 u69632 alloc=17*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258166
[ 0.000000] Kernel command line: console=ttyS0,115200 quiet
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 975104K/1039576K available (10240K kernel code, 1136K rwdata, 2636K rodata, 2048K init, 315K bss, 48088K reserved, 16384K cma-reserved, 236760K highmem)
[ 0.000000] Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xf0800000 - 0xff800000 ( 240 MB)
lowmem : 0xc0000000 - 0xf0000000 ( 768 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0x(ptrval) - 0x(ptrval) (12256 kB)
.init : 0x(ptrval) - 0x(ptrval) (2048 kB)
.data : 0x(ptrval) - 0x(ptrval) (1137 kB)
.bss : 0x(ptrval) - 0x(ptrval) ( 316 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] ftrace: allocating 33749 entries in 99 pages
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] GIC: Using split EOI/Deactivate mode
[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000009] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.000020] Switching to timer-based delay loop, resolution 41ns
[ 0.001581] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[ 0.002572] clocksource: hstimer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370868154 ns
[ 0.003298] Console: colour dummy device 80x30
[ 0.003375] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[ 0.003390] pid_max: default: 32768 minimum: 301
[ 0.003664] Security Framework initialized
[ 0.003675] Yama: disabled by default; enable with sysctl kernel.yama.*
[ 0.003945] AppArmor: AppArmor initialized
[ 0.004052] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.004067] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.005351] CPU: Testing write buffer coherency: ok
[ 0.005972] /cpus/cpu@0 missing clock-frequency property
[ 0.006005] /cpus/cpu@1 missing clock-frequency property
[ 0.006023] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.006868] Setting up static identity map for 0x40400000 - 0x404000a0
[ 0.008419] rcu: Hierarchical SRCU implementation.
[ 0.012371] EFI services will not be available.
[ 0.013045] smp: Bringing up secondary CPUs ...
[ 0.024117] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.024376] smp: Brought up 1 node, 2 CPUs
[ 0.024387] SMP: Total of 2 processors activated (96.00 BogoMIPS).
[ 0.024391] CPU: All CPU(s) started in HYP mode.
[ 0.024394] CPU: Virtualization extensions available.
[ 0.025815] devtmpfs: initialized
[ 0.034982] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 4
[ 0.035408] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.035435] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.036931] pinctrl core: initialized pinctrl subsystem
[ 0.038574] DMI not present or invalid.
[ 0.039170] NET: Registered protocol family 16
[ 0.041627] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.042780] audit: initializing netlink subsys (disabled)
[ 0.043222] audit: type=2000 audit(0.032:1): state=initialized audit_enabled=0 res=1
[ 0.045150] No ATAGs?
[ 0.045327] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.045334] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.046510] Serial: AMBA PL011 UART driver
[ 0.066866] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[ 0.074622] vgaarb: loaded
[ 0.075859] media: Linux media interface: v0.10
[ 0.075914] videodev: Linux video capture interface: v2.00
[ 0.075978] pps_core: LinuxPPS API ver. 1 registered
[ 0.075983] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.076006] PTP clock support registered
[ 0.078522] clocksource: Switched to clocksource arch_sys_counter
[ 0.161681] VFS: Disk quotas dquot_6.6.0
[ 0.161792] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.162772] AppArmor: AppArmor Filesystem Enabled
[ 0.163974] simple-framebuffer 7f736000.framebuffer: framebuffer at 0x7f736000, 0x8ca000 bytes, mapped to 0x(ptrval)
[ 0.163991] simple-framebuffer 7f736000.framebuffer: format=x8r8g8b8, mode=1920x1200x32, linelength=7680
[ 0.205216] Console: switching to colour frame buffer device 240x75
[ 0.245276] simple-framebuffer 7f736000.framebuffer: fb0: simplefb registered!
[ 0.258972] NET: Registered protocol family 2
[ 0.260172] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)
[ 0.260216] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.260293] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.260419] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.260604] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.260676] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.261045] NET: Registered protocol family 1
[ 0.261085] NET: Registered protocol family 44
[ 0.261098] PCI: CLS 0 bytes, default 64
[ 0.261786] Unpacking initramfs...
[ 2.010028] Freeing initrd memory: 20048K
[ 2.010298] kvm [1]: 8-bit VMID
[ 2.011212] kvm [1]: vgic interrupt IRQ16
[ 2.011425] kvm [1]: Hyp mode initialized successfully
[ 2.012366] hw perfevents: no interrupt-affinity property for /pmu, guessing.
[ 2.012671] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
[ 2.015551] Initialise system trusted keyrings
[ 2.015636] Key type blacklist registered
[ 2.016082] workingset: timestamp_bits=14 max_order=18 bucket_order=4
[ 2.025330] zbud: loaded
[ 6.164472] Key type asymmetric registered
[ 6.164485] Asymmetric key parser 'x509' registered
[ 6.164577] bounce: pool size: 64 pages
[ 6.164677] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[ 6.164956] io scheduler noop registered
[ 6.164964] io scheduler deadline registered
[ 6.165247] io scheduler cfq registered (default)
[ 6.165254] io scheduler mq-deadline registered
[ 6.172859] sun4i-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver
[ 6.191796] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 6.195115] console [ttyS0] disabled
[ 6.215407] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 45, base_baud = 1500000) is a U6_16550A
[ 6.226175] console [ttyS0] enabled
[ 6.227530] Serial: AMBA driver
[ 6.231859] libphy: Fixed MDIO Bus: probed
[ 6.232860] mousedev: PS/2 mouse device common for all mice
[ 6.235685] sunxi-rtc 1c20d00.rtc: registered as rtc0
[ 6.235698] sunxi-rtc 1c20d00.rtc: RTC enabled
[ 6.238917] ledtrig-cpu: registered to indicate activity on CPUs
[ 6.240994] NET: Registered protocol family 10
[ 6.307043] Segment Routing with IPv6
[ 6.307176] mip6: Mobile IPv6
[ 6.307194] NET: Registered protocol family 17
[ 6.307480] mpls_gso: MPLS GSO support
[ 6.307584] ThumbEE CPU extension supported.
[ 6.307600] Registering SWP/SWPB emulation handler
[ 6.308796] registered taskstats version 1
[ 6.308803] Loading compiled-in X.509 certificates
[ 6.668032] Loaded X.509 cert 'Debian Secure Boot CA: 6ccece7e4c6c0d1f6149f3dd27dfcc5cbb419ea1'
[ 6.668177] Loaded X.509 cert 'Debian Secure Boot Signer: 00a7468def'
[ 6.668363] zswap: loaded using pool lzo/zbud
[ 6.668724] AppArmor: AppArmor sha1 policy hashing enabled
[ 6.685440] sunxi-rtc 1c20d00.rtc: setting system clock to 1970-01-01 00:23:37 UTC (1417)
[ 6.685456] sr_init: No PMIC hook to init smartreflex
[ 6.686117] vcc3v0: disabling
[ 6.686127] vcc3v3: disabling
[ 6.686132] vcc5v0: disabling
[ 6.686138] ahci-5v: disabling
[ 6.686146] usb0-vbus: disabling
[ 6.686151] usb1-vbus: disabling
[ 6.686157] usb2-vbus: disabling
[ 6.696440] Freeing unused kernel memory: 2048K
[ 6.710792] Run /init as init process
[ 7.649543] sun4i-usb-phy 1c13400.phy: Linked as a consumer to regulator.6
[ 7.649862] sun4i-usb-phy 1c13400.phy: Linked as a consumer to regulator.7
[ 7.650156] sun4i-usb-phy 1c13400.phy: Linked as a consumer to regulator.8
[ 7.671636] sunxi-mmc 1c0f000.mmc: Linked as a consumer to regulator.2
[ 7.711197] sunxi-mmc 1c0f000.mmc: Got CD GPIO
[ 7.718130] usbcore: registered new interface driver usbfs
[ 7.718252] usbcore: registered new interface driver hub
[ 7.718601] usbcore: registered new device driver usb
[ 7.746294] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 7.748211] ehci-platform: EHCI generic platform driver
[ 7.748753] ehci-platform 1c14000.usb: EHCI Host Controller
[ 7.748813] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1
[ 7.756360] sunxi-mmc 1c0f000.mmc: initialized, max. request size: 16384 KB
[ 7.760605] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 7.762413] ohci-platform: OHCI generic platform driver
[ 7.763042] ohci-platform 1c14400.usb: Generic Platform OHCI controller
[ 7.763096] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 2
[ 7.765158] axp20x-i2c 0-0034: AXP20x variant AXP209 found
[ 7.774381] ehci-platform 1c14000.usb: irq 31, io mem 0x01c14000
[ 7.775041] ohci-platform 1c14400.usb: irq 32, io mem 0x01c14400
[ 7.777072] SCSI subsystem initialized
[ 7.787187] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00
[ 7.787875] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[ 7.787890] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 7.787897] usb usb1: Product: EHCI Host Controller
[ 7.787904] usb usb1: Manufacturer: Linux 4.19.0-6-armmp-lpae ehci_hcd
[ 7.787911] usb usb1: SerialNumber: 1c14000.usb
[ 7.789438] hub 1-0:1.0: USB hub found
[ 7.789529] hub 1-0:1.0: 1 port detected
[ 7.791194] ehci-platform 1c1c000.usb: EHCI Host Controller
[ 7.791253] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 3
[ 7.793309] ehci-platform 1c1c000.usb: irq 36, io mem 0x01c1c000
[ 7.797924] mmc0: host does not support reading read-only switch, assuming write-enable
[ 7.800896] mmc0: new high speed SDHC card at address aaaa
[ 7.802385] axp20x-i2c 0-0034: AXP20X driver loaded
[ 7.804460] usb_phy_generic usb_phy_generic.0.auto: usb_phy_generic.0.auto supply vcc not found, using dummy regulator
[ 7.805541] libata version 3.00 loaded.
[ 7.807750] mmcblk0: mmc0:aaaa SC16G 14.8 GiB
[ 7.808514] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00
[ 7.809026] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[ 7.809040] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 7.809048] usb usb3: Product: EHCI Host Controller
[ 7.809055] usb usb3: Manufacturer: Linux 4.19.0-6-armmp-lpae ehci_hcd
[ 7.809062] usb usb3: SerialNumber: 1c1c000.usb
[ 7.810845] hub 3-0:1.0: USB hub found
[ 7.810949] hub 3-0:1.0: 1 port detected
[ 7.825475] ahci-sunxi 1c18000.sata: Linked as a consumer to regulator.5
[ 7.827340] mmcblk0: p1 p2 p3 < p5 >
[ 7.830981] usb_phy_generic usb_phy_generic.0.auto: Linked as a consumer to regulator.0
[ 7.833834] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver
[ 7.833859] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 4
[ 7.841621] sun7i-dwmac 1c50000.ethernet: PTP uses main clock
[ 7.841639] sun7i-dwmac 1c50000.ethernet: no reset control found
[ 7.841687] sun7i-dwmac 1c50000.ethernet: no regulator found
[ 7.842364] sun7i-dwmac 1c50000.ethernet: Version ID not available
[ 7.842383] sun7i-dwmac 1c50000.ethernet: DWMAC1000
[ 7.842392] sun7i-dwmac 1c50000.ethernet: DMA HW capability register supported
[ 7.842400] sun7i-dwmac 1c50000.ethernet: Normal descriptors
[ 7.842407] sun7i-dwmac 1c50000.ethernet: Ring mode enabled
[ 7.843375] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[ 7.843424] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 7.843431] usb usb4: Product: MUSB HDRC host driver
[ 7.843439] usb usb4: Manufacturer: Linux 4.19.0-6-armmp-lpae musb-hcd
[ 7.843445] usb usb4: SerialNumber: musb-hdrc.1.auto
[ 7.860684] hub 4-0:1.0: USB hub found
[ 7.860795] hub 4-0:1.0: 1 port detected
[ 7.862051] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19
[ 7.862066] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 7.862074] usb usb2: Product: Generic Platform OHCI controller
[ 7.862081] usb usb2: Manufacturer: Linux 4.19.0-6-armmp-lpae ohci_hcd
[ 7.862087] usb usb2: SerialNumber: 1c14400.usb
[ 7.863426] hub 2-0:1.0: USB hub found
[ 7.863556] hub 2-0:1.0: 1 port detected
[ 7.864932] ohci-platform 1c1c400.usb: Generic Platform OHCI controller
[ 7.864991] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 5
[ 7.865793] ohci-platform 1c1c400.usb: irq 37, io mem 0x01c1c400
[ 7.882759] ahci-sunxi 1c18000.sata: controller can't do PMP, turning off CAP_PMP
[ 7.882780] ahci-sunxi 1c18000.sata: forcing PORTS_IMPL to 0x1
[ 7.882881] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode
[ 7.882897] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc
[ 7.904738] scsi host0: ahci-sunxi
[ 7.905775] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 35
[ 7.926969] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19
[ 7.926986] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 7.926993] usb usb5: Product: Generic Platform OHCI controller
[ 7.927000] usb usb5: Manufacturer: Linux 4.19.0-6-armmp-lpae ohci_hcd
[ 7.927007] usb usb5: SerialNumber: 1c1c400.usb
[ 7.928301] hub 5-0:1.0: USB hub found
[ 7.928396] hub 5-0:1.0: 1 port detected
[ 7.942260] libphy: stmmac: probed
[ 7.942291] Micrel KSZ9031 Gigabit PHY stmmac-0:01: attached PHY driver [Micrel KSZ9031 Gigabit PHY] (mii_bus:phy_addr=stmmac-0:01, irq=POLL)
[ 8.023555] axp20x-gpio axp20x-gpio: DMA mask not set
[ 8.024091] ldo1: supplied by regulator-dummy
[ 8.029371] axp20x-gpio axp20x-gpio: AXP209 pinctrl and GPIO driver loaded
[ 8.029538] ldo2: supplied by regulator-dummy
[ 8.031443] ldo3: supplied by regulator-dummy
[ 8.039355] ldo4: supplied by regulator-dummy
[ 8.039768] ldo5: supplied by regulator-dummy
[ 8.043820] dcdc2: supplied by regulator-dummy
[ 8.045670] dcdc3: supplied by regulator-dummy
[ 8.053010] axp20x-usb-power-supply axp20x-usb-power-supply: DMA mask not set
[ 8.214639] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 8.226206] random: fast init done
[ 8.227374] ata1: SATA link down (SStatus 0 SControl 300)
[ 8.381828] usb 1-1: New USB device found, idVendor=0bda, idProduct=0316, bcdDevice= 2.04
[ 8.381845] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 8.381853] usb 1-1: Product: USB3.0-CRW
[ 8.381860] usb 1-1: Manufacturer: Generic
[ 8.381867] usb 1-1: SerialNumber: 20120501030900000
[ 8.413850] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 8.415836] scsi host1: usb-storage 1-1:1.0
[ 8.416753] usbcore: registered new interface driver usb-storage
[ 8.420610] usbcore: registered new interface driver uas
[ 8.567892] PM: Image not found (code -22)
[ 8.881782] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 9.449256] scsi 1:0:0:0: Direct-Access Generic- SD/MMC 1.00 PQ: 0 ANSI: 4
[ 9.698163] systemd[1]: System time before build time, advancing clock.
[ 9.772270] systemd[1]: Inserted module 'autofs4'
[ 9.835539] systemd[1]: systemd 241 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
[ 9.836435] systemd[1]: Detected architecture arm.
[ 9.856486] systemd[1]: Set hostname to <debian>.
[ 9.859909] systemd[1]: Failed to bump fs.file-max, ignoring: Invalid argument
[ 10.795668] random: systemd: uninitialized urandom read (16 bytes read)
[ 10.804485] random: systemd: uninitialized urandom read (16 bytes read)
[ 10.805131] systemd[1]: Listening on initctl Compatibility Named Pipe.
[ 10.806085] random: systemd: uninitialized urandom read (16 bytes read)
[ 10.807101] systemd[1]: Listening on udev Kernel Socket.
[ 10.814157] systemd[1]: Created slice system-getty.slice.
[ 10.814450] systemd[1]: Reached target Remote File Systems.
[ 10.815768] systemd[1]: Listening on udev Control Socket.
[ 10.816474] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 11.129795] EXT4-fs (mmcblk0p2): re-mounted. Opts: errors=remount-ro
[ 11.913108] systemd-journald[173]: Received request to flush runtime journal from PID 1
[ 12.988857] sun4i-ss 1c15000.crypto-engine: Die ID 0
[ 13.167409] scsi 1:0:0:0: Attached scsi generic sg0 type 0
[ 13.238874] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
[ 13.334625] sun4i-backend 1e60000.display-backend: Couldn't find matching frontend, frontend features disabled
[ 13.335249] sun4i-drm display-engine: bound 1e60000.display-backend (ops sun4i_backend_ops [sun4i_backend])
[ 13.335294] sun4i-backend 1e40000.display-backend: Couldn't find matching frontend, frontend features disabled
[ 13.335679] sun4i-drm display-engine: bound 1e40000.display-backend (ops sun4i_backend_ops [sun4i_backend])
[ 13.336406] sun4i-drm display-engine: No panel or bridge found... RGB output disabled
[ 13.336446] sun4i-drm display-engine: bound 1c0c000.lcd-controller (ops sun4i_tcon_platform_driver_exit [sun4i_tcon])
[ 13.355594] sun4i-drm display-engine: No panel or bridge found... RGB output disabled
[ 13.355646] sun4i-drm display-engine: bound 1c0d000.lcd-controller (ops sun4i_tcon_platform_driver_exit [sun4i_tcon])
[ 13.368299] sun4i-drm display-engine: bound 1c16000.hdmi (ops sun4i_hdmi_driver_exit [sun4i_drm_hdmi])
[ 13.368322] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 13.368327] [drm] No driver support for vblank timestamp query.
[ 13.368339] checking generic (7f736000 8ca000) vs hw (0 ffffffffffffffff)
[ 13.368345] fb: switching to sun4i-drm-fb from simple
[ 13.368539] Console: switching to colour dummy device 80x30
[ 13.414094] at24 1-0050: 2048 byte 24c16 EEPROM, writable, 16 bytes/write
[ 13.435069] input: axp20x-pek as /devices/platform/soc@1c00000/1c2ac00.i2c/i2c-0/0-0034/axp20x-pek/input/input0
[ 13.446901] Console: switching to colour frame buffer device 240x75
[ 13.452686] axp20x-ac-power-supply axp20x-ac-power-supply: DMA mask not set
[ 13.456509] axp20x-adc axp20x-adc: DMA mask not set
[ 13.458989] axp20x-battery-power-supply axp20x-battery-power-supply: DMA mask not set
[ 13.495022] sun4i-drm display-engine: fb0: DRM emulated frame buffer device
[ 13.577179] [drm] Initialized sun4i-drm 1.0.0 20150629 for display-engine on minor 0
[ 13.971850] sd 1:0:0:0: [sda] 7812096 512-byte logical blocks: (4.00 GB/3.72 GiB)
[ 13.972958] sd 1:0:0:0: [sda] Write Protect is off
[ 13.972976] sd 1:0:0:0: [sda] Mode Sense: 2f 00 00 00
[ 13.976769] sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 13.985495] sda: sda1 sda2 sda3
[ 13.992003] sd 1:0:0:0: [sda] Attached SCSI removable disk
[ 14.506879] Adding 989180k swap on /dev/mmcblk0p5. Priority:-2 extents:1 across:989180k SSFS
[ 14.824637] EXT4-fs (mmcblk0p1): mounting ext2 file system using the ext4 subsystem
[ 14.833404] EXT4-fs (mmcblk0p1): mounted filesystem without journal. Opts: (null)
[ 15.645264] audit: type=1400 audit(1550139123.944:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe" pid=231 comm="apparmor_parser"
[ 15.649207] audit: type=1400 audit(1550139123.948:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe//kmod" pid=231 comm="apparmor_parser"
[ 64.280557] random: crng init done
[ 64.280575] random: 7 urandom warning(s) missed due to ratelimiting
[ 64.373529] EXT4-fs (sda3): mounting ext2 file system using the ext4 subsystem
[ 64.386795] EXT4-fs (sda3): mounted filesystem without journal. Opts: (null)
[ 671.988940] Micrel KSZ9031 Gigabit PHY stmmac-0:01: attached PHY driver [Micrel KSZ9031 Gigabit PHY] (mii_bus:phy_addr=stmmac-0:01, irq=POLL)
[ 671.992969] sun7i-dwmac 1c50000.ethernet eth0: No Safety Features support found
[ 671.992989] sun7i-dwmac 1c50000.ethernet eth0: RX IPC Checksum Offload disabled
[ 671.993003] sun7i-dwmac 1c50000.ethernet eth0: No MAC Management Counters available
[ 671.993013] sun7i-dwmac 1c50000.ethernet eth0: PTP not supported by HW
[ 671.993972] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 674.023384] sun7i-dwmac 1c50000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx
[ 674.023444] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 738.624810] Micrel KSZ9031 Gigabit PHY stmmac-0:01: attached PHY driver [Micrel KSZ9031 Gigabit PHY] (mii_bus:phy_addr=stmmac-0:01, irq=POLL)
[ 738.628507] sun7i-dwmac 1c50000.ethernet eth0: No Safety Features support found
[ 738.628525] sun7i-dwmac 1c50000.ethernet eth0: RX IPC Checksum Offload disabled
[ 738.628540] sun7i-dwmac 1c50000.ethernet eth0: No MAC Management Counters available
[ 738.628549] sun7i-dwmac 1c50000.ethernet eth0: PTP not supported by HW
[ 738.628999] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 756.039301] sun7i-dwmac 1c50000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx
[ 756.039359] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 1062.354260] sd 1:0:0:0: [sda] 7812096 512-byte logical blocks: (4.00 GB/3.72 GiB)
[ 1062.362819] sda: sda1 sda2 sda3
[ 1085.633919] EXT4-fs (sda3): mounting ext2 file system using the ext4 subsystem
[ 1085.644995] EXT4-fs (sda3): warning: mounting unchecked fs, running e2fsck is recommended
[ 1085.647379] EXT4-fs (sda3): mounted filesystem without journal. Opts: (null)
Reply to: