--- Begin Message ---
Subject: debian-installer: Daily Build won't detect Ethernet Card
Package: debian-installer
Severity: important
*** Please type your report below this line ***
-- Package-specific info:
Boot method: buisnesscard
Image version: i386
Date: Thursday May 25, 2006 10:00 AM
Machine: Toshiba A105-S4004
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot: [O]
Detect network card: [E]
Configure network: [E]
Detect CD: [O]
Load installer modules: [O]
Detect hard drives: [ ]
Partition hard drives: [ ]
Create file systems: [ ]
Mount partitions: [ ]
Install base system: [ ]
Install boot loader: [ ]
Installed system ok: [ ]
Comments/Problems:
I first tried the installer using gui mode which I highly enjoyed. The
problems I had with it were: 1. It did not detect my mouse so I had to
use tab and spacebar to do anything. 2. Ctrl-Alt-Del did not reboot nor
did pushing the power button so I had to remove the battery. The
screenshot idea is brilliant but for some reason it wouldn't let me
click on it, onlt continue and go back.
The big issue I had which makes this installer unusable to me is it
didn't detect my Ethernet Card. I tried using text installer and that
didn't work either. This is wierd for this is the fourth daily
build(using busniess car too)
I've tried on this laptop and the first to not detect my Ethernet Card.
I have attached files that may be helpful.
--
-------------------------------------------------------------
Joseph Smidt
jsmidt@byu.edu
0000:00:00.0 Host bridge: Intel Corporation Mobile Memory Controller Hub (rev 03)
Subsystem: Toshiba America Info Systems: Unknown device ff10
Flags: bus master, fast devsel, latency 0
Capabilities: <available only to root>
0000:00:02.0 VGA compatible controller: Intel Corporation Mobile Integrated Graphics Controller (rev 03) (prog-if 00 [VGA])
Subsystem: Toshiba America Info Systems: Unknown device ff10
Flags: bus master, fast devsel, latency 0, IRQ 11
Memory at dc100000 (32-bit, non-prefetchable) [size=512K]
I/O ports at 1800 [size=8]
Memory at c0000000 (32-bit, prefetchable) [size=256M]
Memory at dc200000 (32-bit, non-prefetchable) [size=256K]
Capabilities: <available only to root>
0000:00:02.1 Display controller: Intel Corporation Mobile Integrated Graphics Controller (rev 03)
Subsystem: Toshiba America Info Systems: Unknown device ff10
Flags: bus master, fast devsel, latency 0
Memory at dc180000 (32-bit, non-prefetchable) [size=512K]
Capabilities: <available only to root>
0000:00:1b.0 0403: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 02)
Subsystem: Toshiba America Info Systems: Unknown device ff10
Flags: bus master, fast devsel, latency 0, IRQ 58
Memory at dc240000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <available only to root>
0000:00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 02) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Capabilities: <available only to root>
0000:00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 (rev 02) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=03, subordinate=04, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: d8000000-d9ffffff
Prefetchable memory behind bridge: 00000000d2000000-00000000d3f00000
Capabilities: <available only to root>
0000:00:1c.2 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 3 (rev 02) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=05, subordinate=06, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: da000000-dbffffff
Prefetchable memory behind bridge: 00000000d4000000-00000000d5f00000
Capabilities: <available only to root>
0000:00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #1 (rev 02) (prog-if 00 [UHCI])
Subsystem: Toshiba America Info Systems: Unknown device ff10
Flags: bus master, medium devsel, latency 0, IRQ 50
I/O ports at 1820 [size=32]
0000:00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #2 (rev 02) (prog-if 00 [UHCI])
Subsystem: Toshiba America Info Systems: Unknown device ff10
Flags: bus master, medium devsel, latency 0, IRQ 233
I/O ports at 1840 [size=32]
0000:00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #3 (rev 02) (prog-if 00 [UHCI])
Subsystem: Toshiba America Info Systems: Unknown device ff10
Flags: bus master, medium devsel, latency 0, IRQ 185
I/O ports at 1860 [size=32]
0000:00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #4 (rev 02) (prog-if 00 [UHCI])
Subsystem: Toshiba America Info Systems: Unknown device ff10
Flags: bus master, medium devsel, latency 0, IRQ 177
I/O ports at 1880 [size=32]
0000:00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 02) (prog-if 20 [EHCI])
Subsystem: Toshiba America Info Systems: Unknown device ff10
Flags: bus master, medium devsel, latency 0, IRQ 50
Memory at dc444000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <available only to root>
0000:00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) (prog-if 01 [Subtractive decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=07, subordinate=07, sec-latency=64
I/O behind bridge: 00004000-00004fff
Memory behind bridge: dc000000-dc0fffff
Prefetchable memory behind bridge: 0000000050000000-0000000051f00000
Capabilities: <available only to root>
0000:00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02)
Subsystem: Toshiba America Info Systems: Unknown device ff10
Flags: bus master, medium devsel, latency 0
Capabilities: <available only to root>
0000:00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) Serial ATA Storage Controllers cc=IDE (rev 02) (prog-if 80 [Master])
Subsystem: Toshiba America Info Systems: Unknown device ff10
Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 233
I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at 18b0 [size=16]
Capabilities: <available only to root>
0000:00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 02)
Subsystem: Toshiba America Info Systems: Unknown device ff10
Flags: medium devsel, IRQ 10
I/O ports at 18c0 [size=32]
0000:05:00.0 Network controller: Intel Corporation: Unknown device 4222 (rev 02)
Subsystem: Intel Corporation: Unknown device 1040
Flags: bus master, fast devsel, latency 0, IRQ 10
Memory at da000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <available only to root>
0000:07:06.0 CardBus bridge: Texas Instruments: Unknown device 8039
Subsystem: Toshiba America Info Systems: Unknown device ff10
Flags: bus master, medium devsel, latency 168, IRQ 185
Memory at dc007000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=07, secondary=08, subordinate=0b, sec-latency=176
Memory window 0: 50000000-51fff000 (prefetchable)
Memory window 1: 52000000-53fff000
I/O window 0: 00004400-000044ff
I/O window 1: 00004800-000048ff
16-bit legacy interface ports at 0001
0000:07:06.1 FireWire (IEEE 1394): Texas Instruments: Unknown device 803a (prog-if 10 [OHCI])
Subsystem: Toshiba America Info Systems: Unknown device ff10
Flags: bus master, medium devsel, latency 128, IRQ 169
Memory at dc006000 (32-bit, non-prefetchable) [size=2K]
Memory at dc000000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <available only to root>
0000:07:06.2 Mass storage controller: Texas Instruments: Unknown device 803b
Subsystem: Toshiba America Info Systems: Unknown device ff10
Flags: bus master, medium devsel, latency 128, IRQ 10
Memory at dc004000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <available only to root>
0000:07:06.3 0805: Texas Instruments: Unknown device 803c (prog-if 01)
Subsystem: Toshiba America Info Systems: Unknown device ff10
Flags: bus master, medium devsel, latency 128, IRQ 10
Memory at dc006800 (32-bit, non-prefetchable) [size=256]
Capabilities: <available only to root>
0000:07:08.0 Ethernet controller: Intel Corporation: Unknown device 1092 (rev 02)
Subsystem: Toshiba America Info Systems: Unknown device ff10
Flags: bus master, medium devsel, latency 66, IRQ 225
Memory at dc005000 (32-bit, non-prefetchable) [size=4K]
I/O ports at 4000 [size=64]
Capabilities: <available only to root>
Linux version 2.6.16-1-686-smp (Debian 2.6.16-12) (waldi@debian.org) (gcc version 4.0.4 20060422 (prerelease) (Debian 4.0.3-2)) #2 SMP Thu May 4 18:28:53 UTC 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003f670000 (usable)
BIOS-e820: 000000003f670000 - 000000003f686000 (ACPI data)
BIOS-e820: 000000003f686000 - 000000003f700000 (ACPI NVS)
BIOS-e820: 000000003f700000 - 0000000040000000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
1014MB LOWMEM available.
found SMP MP-table at 000f65d0
On node 0 totalpages: 259696
DMA zone: 4096 pages, LIFO batch:0
DMA32 zone: 0 pages, LIFO batch:0
Normal zone: 255600 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:0
DMI present.
ACPI: RSDP (v000 TOSINV ) @ 0x000f6520
ACPI: RSDT (v001 TOSINV Capell00 0x06040000 LTP 0x00000000) @ 0x3f67e26a
ACPI: FADT (v001 TOSINV CALISTGA 0x06040000 LOHR 0x0000005a) @ 0x3f685dee
ACPI: MADT (v001 INTEL CALISTGA 0x06040000 LOHR 0x0000005a) @ 0x3f685e62
ACPI: HPET (v001 INTEL CALISTGA 0x06040000 LOHR 0x0000005a) @ 0x3f685eca
ACPI: MCFG (v001 INTEL CALISTGA 0x06040000 LOHR 0x0000005a) @ 0x3f685f02
ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06040000 LTP 0x00000001) @ 0x3f685fd8
ACPI: MADT (v001 TOSINV APIC 0x06040000 LTP 0x00000000) @ 0x3f685f70
ACPI: SSDT (v001 SataRe SataPri 0x00001000 INTL 0x20050624) @ 0x3f67f2cc
ACPI: SSDT (v001 SataRe SataSec 0x00001000 INTL 0x20050624) @ 0x3f67ec3a
ACPI: SSDT (v001 PmRef CpuPm 0x00003000 INTL 0x20050624) @ 0x3f67e2b2
ACPI: DSDT (v001 TOSINV CALISTGA 0x06040000 INTL 0x20050624) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: 2 duplicate APIC table ignored.
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:14 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 6:14 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1 already used, trying 2
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
ACPI: HPET id: 0x8086a201 base: 0xfed00000
More than 8 CPUs detected and CONFIG_X86_PC cannot handle it.
Use CONFIG_X86_GENERICARCH or CONFIG_X86_BIGSMP.
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000)
Built 1 zonelists
Kernel command line: root=/dev/sda5 ro install
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1021984k/1038784k available (1504k kernel code, 16048k reserved, 546k data, 176k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
hpet0: at MMIO 0xfed00000 (virtual 0xf0000000), IRQs 2, 8, 0
hpet0: 3 64-bit timers, 14318180 Hz
Using HPET for base-timer
Using HPET for gettimeofday
Detected 1662.512 MHz processor.
Using hpet for high-res timesource
Calibrating delay using timer specific routine.. 3329.12 BogoMIPS (lpj=1664560)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfe9fbff 00000000 00000000 00000000 0000c1a9 00000000 00000000
CPU: After vendor identify, caps: bfe9fbff 00000000 00000000 00000000 0000c1a9 00000000 00000000
monitor/mwait feature present.
using mwait in idle threads.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU: After all inits, caps: bfe9fbff 00000000 00000000 00000140 0000c1a9 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
CPU0: Intel Genuine Intel(R) CPU T2300 @ 1.66GHz stepping 08
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay using timer specific routine.. 3325.14 BogoMIPS (lpj=1662574)
CPU: After generic identify, caps: bfe9fbff 00000000 00000000 00000000 0000c1a9 00000000 00000000
CPU: After vendor identify, caps: bfe9fbff 00000000 00000000 00000000 0000c1a9 00000000 00000000
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfe9fbff 00000000 00000000 00000140 0000c1a9 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel Genuine Intel(R) CPU T2300 @ 1.66GHz stepping 08
Total of 2 processors activated (6654.26 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
migration_cost=1000
checking if image is initramfs... it is
Freeing initrd memory: 4288k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd875, last bus=7
PCI: Using MMCONFIG
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:00:02.0
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.2
PCI: Transparent bridge - 0000:00:1e.0
PCI: Bus #08 (-#0b) may be hidden behind transparent bridge #07 (-#07) (try 'pci=assign-busses')
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 *10 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 *10 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 *11 12 14 15)
ACPI: Embedded Controller [EC0] (gpe 22) interrupt mode.
ACPI: Power Resource [FN00] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 10 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
PCI: Bridge: 0000:00:1c.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.1
IO window: 2000-2fff
MEM window: d8000000-d9ffffff
PREFETCH window: d2000000-d3ffffff
PCI: Bridge: 0000:00:1c.2
IO window: 3000-3fff
MEM window: da000000-dbffffff
PREFETCH window: d4000000-d5ffffff
PCI: Bus 8, cardbus bridge: 0000:07:06.0
IO window: 00004400-000044ff
IO window: 00004800-000048ff
PREFETCH window: 50000000-51ffffff
MEM window: 52000000-53ffffff
PCI: Bridge: 0000:00:1e.0
IO window: 4000-4fff
MEM window: dc000000-dc0fffff
PREFETCH window: 50000000-51ffffff
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1c.1 to 64
ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:1c.2 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
PCI: Enabling device 0000:07:06.0 (0000 -> 0003)
ACPI: PCI Interrupt 0000:07:06.0[A] -> GSI 18 (level, low) -> IRQ 185
Simple Boot Flag at 0x36 set to 0x1
audit: initializing netlink socket (disabled)
audit(1148548006.445:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
0000:00:1d.7 EHCI: BIOS handoff failed (BIOS bug ?) 01010001
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie02]
Allocate Port Service[0000:00:1c.0:pcie03]
ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1c.1 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.1:pcie00]
Allocate Port Service[0000:00:1c.1:pcie02]
Allocate Port Service[0000:00:1c.1:pcie03]
ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:1c.2 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.2:pcie00]
Allocate Port Service[0000:00:1c.2:pcie02]
Allocate Port Service[0000:00:1c.2:pcie03]
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Using IPI No-Shortcut mode
ACPI wakeup devices:
LID HDEF PXS1 PXS2 PXS3 LANC
ACPI: (supports S0 S3 S4 S5)
Freeing unused kernel memory: 176k freed
ACPI: Fan [FAN0] (off)
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: CPU1 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU1] (supports 8 throttling states)
ACPI: Thermal Zone [TZ00] (50 C)
ACPI: Thermal Zone [TZ01] (51 C)
input: AT Translated Set 2 keyboard as /class/input/input0
ieee1394: Initialized config rom entry `ip1394'
e100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI
e100: Copyright(c) 1999-2005 Intel Corporation
ACPI: PCI Interrupt 0000:07:08.0[A] -> GSI 20 (level, low) -> IRQ 225
e100: eth0: e100_probe: addr 0xdc005000, irq 225, MAC addr 00:A0:D1:36:6C:6E
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ACPI: PCI Interrupt 0000:07:06.1[B] -> GSI 17 (level, low) -> IRQ 169
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[169] MMIO=[dc006000-dc0067ff] Max Packet=[2048] IR/IT contexts=[4/8]
SCSI subsystem initialized
libata version 1.20 loaded.
ata_piix 0000:00:1f.2: version 1.05
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 233
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0x18B0 irq 14
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.3
ata1: dev 0 cfg 49:2f00 82:746b 83:7d09 84:6023 85:7469 86:3d09 87:6023 88:203f
ata1: dev 0 ATA-6, max UDMA/100, 195371568 sectors: LBA48
ata1: dev 0 configured for UDMA/100
scsi0 : ata_piix
Vendor: ATA Model: TOSHIBA MK1032GS Rev: AS02
Type: Direct-Access ANSI SCSI revision: 05
ata2: SATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x18B8 irq 15
ata2: dev 0 cfg 49:0f00 82:0000 83:0000 84:0000 85:0000 86:0000 87:0000 88:0407
ata2: dev 0 ATAPI, max UDMA/33
ata2(0): applying bridge limits
ata2: dev 0 configured for UDMA/33
scsi1 : ata_piix
Vendor: MATSHITA Model: DVD-RAM UJ-841S Rev: 1.50
Type: CD-ROM ANSI SCSI revision: 05
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 50
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 50, io base 0x00001820
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
SCSI device sda: 195371568 512-byte hdwr sectors (100030 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 195371568 512-byte hdwr sectors (100030 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 233
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 233, io base 0x00001840
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
sd 0:0:0:0: Attached scsi disk sda
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 185, io base 0x00001860
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 177, io base 0x00001880
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 50
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: irq 50, io mem 0xdc444000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
Attempting manual resume
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00080da0d1366c6e]
Real Time Clock Driver v1.12ac
ACPI: PCI Interrupt 0000:07:06.0[A] -> GSI 18 (level, low) -> IRQ 185
Yenta: CardBus bridge found at 0000:07:06.0 [1179:ff10]
Linux agpgart interface v0.101 (c) Dave Jones
Yenta: ISA IRQ mask 0x0cf8, PCI irq 185
Socket status: 30000006
pcmcia: parent PCI bridge I/O window: 0x4000 - 0x4fff
cs: IO port probe 0x4000-0x4fff: clean.
pcmcia: parent PCI bridge Memory window: 0xdc000000 - 0xdc0fffff
pcmcia: parent PCI bridge Memory window: 0x50000000 - 0x51ffffff
agpgart: Detected an Intel 945GM Chipset.
agpgart: Detected 7932K stolen memory.
agpgart: AGP aperture is 256M @ 0xc0000000
sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
hw_random hardware driver 1.0.0 loaded
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 1:0:0:0: Attached scsi generic sg1 type 5
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 58
PCI: Setting latency timer of device 0000:00:1b.0 to 64
hda_codec: Unknown model for ALC861, trying auto-probe from BIOS...
cs: IO port probe 0x100-0x3af: excluding 0x370-0x377
cs: IO port probe 0x3e0-0x4ff: excluding 0x3f0-0x3f7 0x400-0x407 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
Synaptics Touchpad, model: 1, fw: 6.2, id: 0x2a0b1, caps: 0xb04713/0x60040d
synaptics: Toshiba Satellite A105 detected, limiting rate to 40pps.
input: SynPS/2 Synaptics TouchPad as /class/input/input1
ts: Compaq touchscreen protocol output
mice: PS/2 mouse device common for all mice
Adding 1911692k swap on /dev/sda6. Priority:-1 extents:1 across:1911692k
EXT3 FS on sda5, internal journal
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
ieee1394: sbp2: Try serialize_io=0 for better performance
device-mapper: 4.5.0-ioctl (2005-10-04) initialised: dm-devel@redhat.com
pcmcia: Detected deprecated PCMCIA ioctl usage.
pcmcia: This interface will soon be removed from the kernel; please expect breakage unless you upgrade to new tools.
pcmcia: see http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for details.
i8xx TCO timer: heartbeat value must be 2<heartbeat<39, using 30
i8xx TCO timer: initialized (0x1060). heartbeat=30 sec (nowayout=0)
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
ACPI: Battery Slot [BAT0] (battery present)
ACPI: AC Adapter [ADP0] (on-line)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ACPI: Power Button (CM) [PWRB]
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
--- End Message ---