Bug#290401: grub error after reboot
Package: installation-reports
Debian-installer-version:
20050112 from http://cdimage.debian.org/pub/cdimage-testing/daily/i386/
uname -a:
Linux powerstation 2.4.27-1-386 #1 Wed Dec 1 19:43:08 JST 2004 i686 GNU/Linux
Date: 13.01.2005 12:30
Method:
network installation from ftp.de.debian.org, booted from
sarge-i386-netinst.iso, no proxy used, installation mode default (linux)
Machine:
selfmade machine
Processor:
AMD Athlon 700 Mhz
Memory:
386716 kB
Root Device:
IDE Maxtor 4K080H4, 80GB
Root Size/partition table:
hda1 ext3 mount on /
hda2 swap
Output of lspci and lspci -n:
0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133]
(rev 03)
0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133 AGP]
0000:00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South]
(rev 40)
0000:00:07.1 IDE interface: VIA Technologies, Inc.
VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
0000:00:07.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 16)
0000:00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev
40)
0000:00:07.5 Multimedia audio controller: VIA Technologies, Inc. VT82C686 AC97
Audio Controller (rev 50)
0000:00:0a.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado]
(rev 74)
0000:00:0c.0 Ethernet controller: VIA Technologies, Inc. VT6105 [Rhine-III]
(rev 86)
0000:00:0d.0 VGA compatible controller: S3 Inc. 86c764/765 [Trio32/64/64V+]
(rev 44)
0000:00:00.0 0600: 1106:0305 (rev 03)
0000:00:01.0 0604: 1106:8305
0000:00:07.0 0601: 1106:0686 (rev 40)
0000:00:07.1 0101: 1106:0571 (rev 06)
0000:00:07.2 0c03: 1106:3038 (rev 16)
0000:00:07.4 0680: 1106:3057 (rev 40)
0000:00:07.5 0401: 1106:3058 (rev 50)
0000:00:0a.0 0200: 10b7:9200 (rev 74)
0000:00:0c.0 0200: 1106:3106 (rev 86)
0000:00:0d.0 0300: 5333:8811 (rev 44)
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot worked: [ O]
Configure network HW: [ O]
Config network: [O ]
Detect CD: [ O]
Load installer modules: [ O] (no errors seen during installation proccess)
Detect hard drives: [O ]
Partition hard drives: [O ]
Create file systems: [O ]
Mount partitions: [ O]
Install base system: [O ]
Install boot loader: [O ]
Reboot: [ E]
Comments/Problems:
In the default installation mode (linux), the system installs grub as default
bootloader. no problems and no error messages during the installation
proccess. After reboot comes this message:
Grub loading, please wait
Error2
Could it be that some of the required modules for this machine wasn`t
load/installed at boot time? The same installation (default linux...just
press Enter at the boot prompt) on a Toshiba Tecra 8100 completes with no
errors.
Greetings
Jens Voskuhl
Reply to: