|
Package: installation-reports
INSTALL REPORT
Debian-installer-version: Nov 8 2004, obtained at http://www.debian.org/devel/debian-installer/ (i386)
uname -a: Linux the-cs-pig 2.4.27-1-386 #1 Fri Sep 3 06:24:46 UTC 2004 i686 GNU/Linux
Date: Nov 9 2004
Method: full ISO image of Sarge
Machine: PC
Processor: AMD Athlon 900
Memory: 384 MB
Root Device: scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36 <Adaptec 2940 Ultra SCSI adapter> aic7880: Ultra Wide Channel A, SCSI Id=7, 16/253 SCBs (scsi0:A:0): 40.000MB/s transfers (20.000MHz, offset 8, 16bit) Vendor: SEAGATE Model: ST36530W Rev: 1206 Type: Direct-Access ANSI SCSI revision: 02
Root Size/partition table: # /etc/fstab: static file system information. # # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc defaults 0 0 /dev/sda2 / ext3 defaults,errors=remount-ro 0 1 /dev/sda1 /boot ext3 defaults 0 2 /dev/sda7 /cs ext3 defaults 0 2 /dev/sda3 /usr ext3 defaults 0 2 /dev/sda6 /var ext3 defaults 0 2 /dev/sda5 none swap sw 0 0 /dev/hdc /media/cdrom0 iso9660 ro,user,noauto 0 0 /dev/fd0 /media/floppy0 auto rw,user,noauto 0 0
Output of lspci and lspci -n: 0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133] (rev 02) 0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133 AGP] 0000:00:04.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 22) 0000:00:04.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 10) 0000:00:04.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 10) 0000:00:04.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 10) 0000:00:04.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 30) 0000:00:0a.0 Ethernet controller: D-Link System Inc RTL8139 Ethernet (rev 10) 0000:00:0b.0 Ethernet controller: 3Com Corporation 3c900B-TPO Etherlink XL [Cyclone] (rev 04) 0000:00:0c.0 SCSI storage controller: Adaptec AHA-2940U/UW/D / AIC-7881U (rev 01) 0000:01:00.0 VGA compatible controller: nVidia Corporation NV11 [GeForce2 MX/MX 400] (rev a1)
0000:00:00.0 0600: 1106:0305 (rev 02) 0000:00:01.0 0604: 1106:8305 0000:00:04.0 0601: 1106:0686 (rev 22) 0000:00:04.1 0101: 1106:0571 (rev 10) 0000:00:04.2 0c03: 1106:3038 (rev 10) 0000:00:04.3 0c03: 1106:3038 (rev 10) 0000:00:04.4 0680: 1106:3057 (rev 30) 0000:00:0a.0 0200: 1186:1300 (rev 10) 0000:00:0b.0 0200: 10b7:9004 (rev 04) 0000:00:0c.0 0100: 9004:8178 (rev 01) 0000:01:00.0 0300: 10de:0110 (rev a1)
Base System Installation Checklist: [O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot worked: [ O] Configure network HW: [ E] wouldn’t load Realtek 8139 NIC. Insmod said device was in use. Rebooted after adding 8139too to /etc/modules and config’d /etc/network/interfaces and then success Config network: [ O] Loaded 3com 3c59x card ok Detect CD: [ O] Load installer modules: [ O] Detect hard drives: [ O] Partition hard drives: [ O] Create file systems: [ O] Mount partitions: [ O] Install base system: [ O] Install boot loader: [ O] Reboot: [ O]
Comments/Problems:
I like the installer much better than Woody. It’s a lot easier to follow…. Like partitioning and formatting the hdd. Still installs packages that I don’t need (portmap, nfs-common, pppoe) but I removed after install.
Install logs and other status info is available in /var/log/debian-installer/. Once you have filled out this report, mail it to submit@bugs.debian.org.
Jonathan @ Compton
|