On Tue, Oct 05, 2004 at 04:44:56PM -0400, Joey Hess wrote: > Tapio Lehtonen wrote: > > I boot with linux26. Boot works from IDE CD, kernel module for Adaptec > > SCSI is chosen. Hard disk is SCSI. But installer fails to find the > > SCSI drive. I installed this same machine with RC1, then it worked. > > It seems to me the kernel module most not be seeing or working with your > drive. If you can send the syslog from the install, we might be able to > see why. > I boot: linux26. I copied the logs to diskette and put them in http://www.hyperaika.fi/~tlehtone/peli/ Excerpts from syslog: Oct 6 01:10:16 hw-detect: Loading modules... Oct 6 01:10:16 hw-detect: Detected module 'aic7xxx' for 'Adaptec AIC-7899P U160/m' Oct 6 01:10:17 hw-detect: Trying to load module 'aic7xxx' Oct 6 01:10:17 kernel: SCSI subsystem initialized Oct 6 01:10:17 hw-detect: Detected module 'usb-storage' for 'USB storage' Oct 6 01:10:17 hw-detect: Trying to load module 'usb-storage' Oct 6 01:10:27 anna[3008]: DEBUG: resolver (harddrive-detection): search, dependency from partman Oct 6 01:10:27 anna[3008]: DEBUG: resolver (hw-detect-full): accept cdebconf-udeb, already installed Oct 6 01:10:27 anna[3008]: DEBUG: resolver (hw-detect-full): accept hw-detect, already installed Oct 6 01:10:27 anna[3008]: DEBUG: resolver (hw-detect-full): mark, dependency from partman Oct 6 01:10:27 anna[3008]: DEBUG: resolver (partman): mark, dependency from base-installer Oct 6 01:10:47 main-menu[502]: DEBUG: configure harddrive-detection, status: 0 Oct 6 01:10:47 main-menu[502]: DEBUG: virtual package harddrive-detection Oct 6 01:10:54 main-menu[502]: (process:5776): unsupported Oct 6 01:10:54 main-menu[502]: (process:5776): kernelmodules_basicfilesystems Oct 6 01:10:54 main-menu[502]: (process:5776): kernelmodules_ext3 Oct 6 01:10:54 main-menu[502]: (process:5776): kernelmodules_jfs Oct 6 01:10:54 main-menu[502]: (process:5776): kernelmodules_reiserfs Oct 6 01:10:54 main-menu[502]: (process:5776): kernelmodules_xfs Oct 6 01:10:54 main-menu[502]: (process:5776): umount_target Oct 6 01:10:54 main-menu[502]: (process:5776): parted Oct 6 01:10:54 main-menu[502]: (process:5776): md-devices Oct 6 01:10:54 main-menu[502]: (process:5776): grep: Oct 6 01:10:54 main-menu[502]: (process:5776): /proc/mdstat Oct 6 01:10:54 main-menu[502]: (process:5776): : No such file or directory Oct 6 01:10:54 main-menu[502]: (process:5776): dump Oct 6 01:10:54 main-menu[502]: (process:5776): lvm Oct 6 01:10:54 main-menu[502]: (process:5776): Oct 6 01:10:54 main-menu[502]: (process:5776): No volume groups found Oct 6 01:10:54 main-menu[502]: (process:5776): Oct 6 01:10:54 main-menu[502]: (process:5776): md Oct 6 01:10:54 main-menu[502]: (process:5776): no_media Oct 6 01:10:54 main-menu[502]: INFO: Menu item 'partman' succeeded but requested to be left unconfigured. Oct 6 01:10:54 main-menu[502]: INFO: Modifying debconf priority limit from 'high' to 'medium' Oct 6 01:10:54 debconf: Setting debconf/priority to medium I started shell in the installer, there lsmod shows that aic7xxs is loaded but used is 0. This Dell 1400SC has Adaptec AIC-7899 with Fujitsu model MAN3184MP. I attach dmesg output from the running system, installed with the previous installer. It has kernel 2.6.7-1-386. This system works OK. > > I also saw the known error of red background. The installer screen > > background was sometimes red. Seemed random, most of the times it was > > blue but I did get red twice. Even when it was red, some screens > > showed blue bagkground, but the next screen was again red. > > Seems to me you're describing a regular error message here. The first screen, choose country, has red background. It continues with red, except some screen had blue background. Seems today every time I boot I get red. Yesterday it was blue most of the times. -- Tapio Lehtonen Tapio.Lehtonen@IKI.FI GPG public key from http://www.iki.fi/Tapio.Lehtonen
) @ 0x000fdcd0
ACPI: RSDT (v001 DELL PE1400 0x00000002 MSFT 0x0100000a) @ 0x000fdce4
ACPI: FADT (v001 DELL PE1400 0x00000002 MSFT 0x0100000a) @ 0x000fdd10
ACPI: MADT (v001 DELL PE1400 0x00000002 MSFT 0x0100000a) @ 0x000fdd84
ACPI: DSDT (v001 DELL PE1400 0x00000002 MSFT 0x0100000a) @ 0x00000000
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:8 APIC version 17
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x00] disabled)
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] global_irq_base[0x0])
IOAPIC[0]: Assigned apic_id 1
IOAPIC[0]: apic_id 1, version 17, address 0xfec00000, GSI 0-15
ACPI: IOAPIC (id[0x02] address[0xfec01000] global_irq_base[0x10])
IOAPIC[1]: Assigned apic_id 2
IOAPIC[1]: apic_id 2, version 17, address 0xfec01000, GSI 16-31
Enabling APIC mode: Flat. Using 2 I/O APICs
Using ACPI (MADT) for SMP configuration information
Built 1 zonelists
Kernel command line: root=/dev/sda1 ro
Initializing CPU#0
PID hash table entries: 1024 (order 10: 8192 bytes)
Detected 997.849 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Memory: 252628k/262136k available (1309k kernel code, 8772k reserved, 701k data, 204k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 1982.46 BogoMIPS
Security Scaffold v1.0.0 initialized
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0383fbff 00000000 00000000 00000000
CPU: After vendor identify, caps: 0383fbff 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After all inits, caps: 0383fbff 00000000 00000000 00000040
CPU: Intel Pentium III (Coppermine) stepping 0a
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
ENABLING IO-APIC IRQs
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-1, 2-2, 2-3, 2-4, 2-5, 2-6, 2-7, 2-8, 2-9, 2-10, 2-11, 2-12, 2-13, 2-14, 2-15 not connected.
..TIMER: vector=0x31 pin1=0 pin2=-1
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 997.0315 MHz.
..... host bus clock speed is 132.0975 MHz.
checking if image is initramfs...it isn't (ungzip failed); looks like an initrd
Freeing initrd memory: 4256k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfc7de, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Root Bridge [PCI1] (00:01)
PCI: Probing PCI hardware (bus 01)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
ACPI: PCI Interrupt Link [LNKI] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
ACPI: PCI Interrupt Link [LNKJ] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
ACPI: PCI Interrupt Link [LNKK] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
ACPI: PCI Interrupt Link [LNKL] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
ACPI: PCI Interrupt Link [LNKM] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
ACPI: PCI Interrupt Link [LNKN] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
ACPI: PCI Interrupt Link [LNKO] (IRQs 3 4 *5 6 7 9 10 11 12 14)
ACPI: PCI Interrupt Link [LNKP] (IRQs 3 4 5 6 7 9 10 *11 12 14)
ACPI: PCI Interrupt Link [LUSB] (IRQs 3 4 5 6 7 *10 11 12 14)
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00fe2d0
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xe2f4, dseg 0x40
pnp: 00:00: ioport range 0x800-0x83f has been reserved
pnp: 00:00: ioport range 0x580-0x58f has been reserved
pnp: 00:00: ioport range 0x2c00-0x2c7f has been reserved
pnp: 00:11: ioport range 0xc00-0xc01 has been reserved
pnp: 00:11: ioport range 0xc06-0xc08 has been reserved
pnp: 00:11: ioport range 0xc14-0xc14 has been reserved
pnp: 00:11: ioport range 0xc50-0xc52 has been reserved
pnp: 00:11: ioport range 0xc6c-0xc6f has been reserved
pnp: 00:11: ioport range 0xcd6-0xcd7 has been reserved
pnp: 00:11: ioport range 0xf50-0xf57 has been reserved
PnPBIOS: 17 nodes reported by PnP BIOS; 17 recorded by driver
ACPI: PCI Interrupt Link [LUSB] enabled at IRQ 10
00:00:0f[A] -> 1-10 -> IRQ 10 level low
00:00:04[A] -> 2-9 -> IRQ 25 level low
00:00:04[B] -> 2-10 -> IRQ 26 level low
00:00:04[C] -> 2-11 -> IRQ 27 level low
00:00:04[D] -> 2-12 -> IRQ 28 level low
00:00:02[A] -> 2-0 -> IRQ 16 level low
00:01:02[A] -> 2-14 -> IRQ 30 level low
00:01:02[B] -> 2-15 -> IRQ 31 level low
00:01:04[A] -> 2-1 -> IRQ 17 level low
00:01:04[B] -> 2-2 -> IRQ 18 level low
00:01:04[C] -> 2-3 -> IRQ 19 level low
00:01:04[D] -> 2-4 -> IRQ 20 level low
00:01:08[A] -> 2-5 -> IRQ 21 level low
00:01:08[B] -> 2-6 -> IRQ 22 level low
00:01:08[C] -> 2-7 -> IRQ 23 level low
00:01:08[D] -> 2-8 -> IRQ 24 level low
number of MP IRQ sources: 16.
number of IO-APIC #1 registers: 16.
number of IO-APIC #2 registers: 16.
testing the IO APIC.......................
IO APIC #1......
.... register #00: 01000000
....... : physical APIC id: 01
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 000F0011
....... : max redirection entries: 000F
....... : PRQ implemented: 0
....... : IO APIC version: 0011
.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 001 01 0 0 0 0 0 1 1 31
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 41
03 001 01 0 0 0 0 0 1 1 49
04 001 01 0 0 0 0 0 1 1 51
05 001 01 0 0 0 0 0 1 1 59
06 001 01 0 0 0 0 0 1 1 61
07 001 01 0 0 0 0 0 1 1 69
08 001 01 0 0 0 0 0 1 1 71
09 001 01 0 1 0 1 0 1 1 79
0a 001 01 1 1 0 1 0 1 1 81
0b 001 01 0 0 0 0 0 1 1 89
0c 001 01 0 0 0 0 0 1 1 91
0d 001 01 0 0 0 0 0 1 1 99
0e 001 01 0 0 0 0 0 1 1 A1
0f 001 01 0 0 0 0 0 1 1 A9
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 000F0011
....... : max redirection entries: 000F
....... : PRQ implemented: 0
....... : IO APIC version: 0011
.... register #02: 0F000000
....... : arbitration: 0F
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 001 01 1 1 0 1 0 1 1 D1
01 001 01 1 1 0 1 0 1 1 E9
02 001 01 1 1 0 1 0 1 1 32
03 001 01 1 1 0 1 0 1 1 3A
04 001 01 1 1 0 1 0 1 1 42
05 001 01 1 1 0 1 0 1 1 4A
06 001 01 1 1 0 1 0 1 1 52
07 001 01 1 1 0 1 0 1 1 5A
08 001 01 1 1 0 1 0 1 1 62
09 001 01 1 1 0 1 0 1 1 B1
0a 001 01 1 1 0 1 0 1 1 B9
0b 001 01 1 1 0 1 0 1 1 C1
0c 001 01 1 1 0 1 0 1 1 C9
0d 000 00 1 0 0 0 0 0 0 00
0e 001 01 1 1 0 1 0 1 1 D9
0f 001 01 1 1 0 1 0 1 1 E1
IRQ to pin mappings:
IRQ0 -> 0:0
IRQ1 -> 0:1
IRQ2 -> 0:2
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 1:0
IRQ17 -> 1:1
IRQ18 -> 1:2
IRQ19 -> 1:3
IRQ20 -> 1:4
IRQ21 -> 1:5
IRQ22 -> 1:6
IRQ23 -> 1:7
IRQ24 -> 1:8
IRQ25 -> 1:9
IRQ26 -> 1:10
IRQ27 -> 1:11
IRQ28 -> 1:12
IRQ30 -> 1:14
IRQ31 -> 1:15
.................................... done.
PCI: Using ACPI for IRQ routing
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
EISA: Probing bus 0 at eisa0
NET: Registered protocol family 2
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI: (supports S0 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4256 blocks [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 204k freed
vesafb: probe of vesafb0 failed with error -6
NET: Registered protocol family 1
SCSI subsystem initialized
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec aic7899 Ultra160 SCSI adapter>
aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
Using anticipatory io scheduler
(scsi0:A:0): 160.000MB/s transfers (80.000MHz DT, offset 127, 16bit)
Vendor: FUJITSU Model: MAN3184MP Rev: 5507
Type: Direct-Access ANSI SCSI revision: 03
scsi0:A:0:0: Tagged Queuing enabled. Depth 8
scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec aic7899 Ultra160 SCSI adapter>
aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/253 SCBs
SCSI device sda: 35566478 512-byte hdwr sectors (18210 MB)
SCSI device sda: drive cache: write through
/dev/scsi/host0/bus0/target0/lun0: p1 p2 < p5 p6 >
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Adding 497972k swap on /dev/sda6. Priority:-1 extents:1
EXT3 FS on sda1, internal journal
Real Time Clock Driver v1.12
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
hda: CRD-8482B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: ATAPI 48X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.20
Capability LSM initialized
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
e100: Intel(R) PRO/100 Network Driver, 3.0.18
e100: Copyright(c) 1999-2004 Intel Corporation
e100: eth0: e100_probe: addr 0xfe102000, irq 16, MAC addr 00:B0:D0:FC:36:85
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, using FIFO [PCSPP,TRISTATE,COMPAT,ECP]
inserting floppy driver for 2.6.7-1-386
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
input: PS/2 Logitech Mouse on isa0060/serio1
mice: PS/2 mouse device common for all mice
ts: Compaq touchscreen protocol output
input: PC Speaker
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Maximum main memory to use for agp memory: 203M
agpgart: unable to determine aperture size.
agpgart: agp_backend_initialize() failed.
agpgart-serverworks: probe of 0000:00:00.0 failed with error -22
agpgart: Maximum main memory to use for agp memory: 203M
agpgart: unable to determine aperture size.
agpgart: agp_backend_initialize() failed.
agpgart-serverworks: probe of 0000:00:00.1 failed with error -22
eepro100.c:v1.09j-t 9/29/99 Donald Becker http://www.scyld.com/network/eepro100.html
eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <saw@saw.sw.com.sg> and others
SvrWks OSB4: IDE controller at PCI slot 0000:00:0f.1
SvrWks OSB4: chipset revision 0
SvrWks OSB4: not 100% native mode: will probe irqs later
SvrWks OSB4: port 0x01f0 already claimed by ide0
ide1: BM-DMA at 0x08b8-0x08bf, BIOS settings: hdc:pio, hdd:pio
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
ohci_hcd 0000:00:0f.2: ServerWorks OSB4/CSB5 OHCI USB Controller
ohci_hcd 0000:00:0f.2: irq 10, pci mem d0973000
ohci_hcd 0000:00:0f.2: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
usb 1-2: new low speed USB device using address 2
usbcore: registered new driver hiddev
input: USB HID v1.10 Mouse [Logitech USB Mouse] on usb-0000:00:0f.2-2
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
kobject_register failed for aic79xx (-17)
[<c0189f53>] kobject_register+0x35/0x3d
[<c01cf107>] bus_add_driver+0x38/0x67
[<c01cf397>] driver_register+0x2d/0x31
[<c0191fce>] pci_register_driver+0x4e/0x6b
[<d0a4c4e5>] ahd_linux_pci_init+0xa/0x12 [aic79xx]
[<d0a457ed>] ahd_linux_detect+0x3c/0x6c [aic79xx]
[<d08ac00a>] ahd_linux_init+0xa/0x19 [aic79xx]
[<c012a5ce>] sys_init_module+0xe3/0x1d4
[<c0105f9f>] syscall_call+0x7/0xb
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
NET: Registered protocol family 17
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02c3f00(lo)
IPv6 over IPv4 tunneling driver
apm: BIOS not found.
mtrr: Serverworks LE detected. Write-combining disabled.
mtrr: your processor doesn't support write-combining
mtrr: Serverworks LE detected. Write-combining disabled.
mtrr: your processor doesn't support write-combining
eth0: no IPv6 routers present
Attachment:
signature.asc
Description: Digital signature