RE: SS4000E Fan speed, LEDS and power button
Rescue mode didn't work, see log. Blows right through to login without
starting d-i.
I'm not familiar with loadable modules. Does the kernel need rebuilding?
CJW
--Log start--
+No network interfaces found
EM-438/EM-7220 ver.AG0 2006-05-23
== Executing boot script in 1.000 seconds - enter ^C to abort
^C
RedBoot> ^C
RedBoot> fis list
Name FLASH addr Mem addr Length Entry point
RedBoot 0xF0000000 0xF0000000 0x00040000 0x00000000
RedBoot config 0xF07C0000 0xF07C0000 0x00001000 0x00000000
FIS directory 0xF07E0000 0xF07E0000 0x00020000 0x00000000
rammode 0xF0700000 0x00200000 0x00040000 0x00200000
zImage 0xF0040000 0x01008000 0x00200000 0x01008000
ramdisk.gz 0xF0240000 0x01800000 0x00400000 0x01800000
wmdata 0xF0640000 0xF0640000 0x000C0000 0x01008000
naskey 0xF0740000 0xF0740000 0x00020000 0x01008000
log 0xF0760000 0xF0760000 0x00040000 0x01008000
vendor 0xF07A0000 0xF07A0000 0x00020000 0x01008000
RedBoot>
RedBoot>
RedBoot> fis load ramdisk.gz
RedBoot> fis load zImage
RedBoot> exec -c "console=ttyS0,115200 rw root=/dev/ram mem=256M@0xa0000000
rescue/enable=true" -r 0x01800000
** Error: Illegal command: "<Not a string: 0x10A64>"
<<<some funny error with copy/paste>>>
RedBoot> exec -c "console=ttyS0,115200 rw root=/dev/ram mem=256M@0xa0000000
rescue/enable=true" -r 0x01800000
Using base address 0x01008000 and length 0x00132fa8
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.32-5-iop32x (Debian 2.6.32-45)
(dannf@debian.org) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 Sun May 6
07:47:32 UTC 2012
[ 0.000000] CPU: XScale-80219 [69052e30] revision 0 (ARMv5TE),
cr=0000397f
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: Lanner EM7210
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total
pages: 65024
[ 0.000000] Kernel command line: console=ttyS0,115200 rw root=/dev/ram
mem=256M@0xa0000000 rescue/enable=true
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072
bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 256MB = 256MB total
[ 0.000000] Memory: 251776KB available (3084K code, 444K data, 112K init,
0K highmem)
[ 0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0,
CPUs=1, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:32
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] Calibrating delay loop... 599.65 BogoMIPS (lpj=2998272)
[ 0.220000] Security Framework initialized
[ 0.220000] SELinux: Disabled at boot.
[ 0.220000] Mount-cache hash table entries: 512
[ 0.220000] Initializing cgroup subsys ns
[ 0.220000] Initializing cgroup subsys cpuacct
[ 0.220000] Initializing cgroup subsys devices
[ 0.220000] Initializing cgroup subsys freezer
[ 0.220000] Initializing cgroup subsys net_cls
[ 0.220000] CPU: Testing write buffer coherency: ok
[ 0.220000] devtmpfs: initialized
[ 0.220000] regulator: core version 0.5
[ 0.220000] NET: Registered protocol family 16
[ 0.220000] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.220000] pci 0000:00:01.0: PME# disabled
[ 0.220000] pci 0000:00:05.0: PME# supported from D0 D1 D2 D3hot
[ 0.220000] pci 0000:00:05.0: PME# disabled
[ 0.220000] pci 0000:00:05.1: PME# supported from D0 D1 D2 D3hot
[ 0.220000] pci 0000:00:05.1: PME# disabled
[ 0.220000] pci 0000:00:05.2: PME# supported from D0 D1 D2 D3hot
[ 0.220000] pci 0000:00:05.2: PME# disabled
[ 0.220000] PCI: bus0: Fast back to back transfers disabled
[ 0.230000] bio: create slab <bio-0> at 0
[ 0.230000] vgaarb: loaded
[ 0.240000] NET: Registered protocol family 2
[ 0.240000] IP route cache hash table entries: 2048 (order: 1, 8192
bytes)
[ 0.240000] TCP established hash table entries: 8192 (order: 4, 65536
bytes)
[ 0.250000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.250000] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.250000] TCP reno registered
[ 0.250000] NET: Registered protocol family 1
[ 0.250000] Unpacking initramfs...
[ 0.950000] Freeing initrd memory: 4096K
[ 0.950000] NetWinder Floating Point Emulator V0.97 (double precision)
[ 0.950000] audit: initializing netlink socket (disabled)
[ 0.950000] type=2000 audit(0.950:1): initialized
[ 0.970000] VFS: Disk quotas dquot_6.5.2
[ 0.970000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.970000] msgmni has been set to 500
[ 0.970000] alg: No test for stdrng (krng)
[ 0.970000] Block layer SCSI generic (bsg) driver version 0.4 loaded
(major 253)
[ 0.970000] io scheduler noop registered
[ 0.970000] io scheduler anticipatory registered
[ 0.970000] io scheduler deadline registered
[ 0.970000] io scheduler cfq registered (default)
[ 0.980000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.980000] serial8250.0: ttyS0 at MMIO 0xfe800000 (irq = 28) is a 16550A
[ 1.330000] console [ttyS0] enabled
[ 1.330000] physmap platform flash device: 02000000 at f0000000
[ 1.340000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
[ 1.340000] Intel/Sharp Extended Query Table at 0x0031
[ 1.350000] Intel/Sharp Extended Query Table at 0x0031
[ 1.350000] Using buffer write method
[ 1.360000] cfi_cmdset_0001: Erase suspend on write enabled
[ 1.360000] Searching for RedBoot partition table in physmap-flash.0 at
offset 0x7e0000
[ 1.500000] 10 RedBoot partitions found on MTD device physmap-flash.0
[ 1.500000] Creating 10 MTD partitions on "physmap-flash.0":
[ 1.510000] 0x000000000000-0x000000040000 : "RedBoot"
[ 1.520000] 0x000000040000-0x000000240000 : "zImage"
[ 1.520000] 0x000000240000-0x000000640000 : "ramdisk.gz"
[ 1.530000] 0x000000640000-0x000000700000 : "wmdata"
[ 1.540000] 0x000000700000-0x000000740000 : "rammode"
[ 1.540000] 0x000000740000-0x000000760000 : "naskey"
[ 1.550000] 0x000000760000-0x0000007a0000 : "log"
[ 1.550000] 0x0000007a0000-0x0000007c0000 : "vendor"
[ 1.560000] 0x0000007c0000-0x0000007c1000 : "RedBoot config"
[ 1.570000] mtd: partition "RedBoot config" doesn't end on an erase block
-- force read-only
[ 1.580000] 0x0000007e0000-0x000000800000 : "FIS directory"
[ 1.580000] mice: PS/2 mouse device common for all mice
[ 1.590000] i2c /dev entries driver
[ 1.600000] rtc-rs5c372 0-0032: rs5c372a found, 24hr, driver version 0.6
[ 1.600000] rtc-rs5c372 0-0032: rtc core: registered rtc-rs5c372 as rtc0
[ 1.610000] i2c i2c-0: failed,FF11,11,05
[ 1.640000] iop-adma iop-adma.0: Intel(R) IOP: ( cpy intr )
[ 1.660000] iop-adma iop-adma.1: Intel(R) IOP: ( cpy intr )
[ 1.660000] TCP cubic registered
[ 1.670000] NET: Registered protocol family 17
[ 1.670000] XScale DSP coprocessor detected.
[ 1.680000] registered taskstats version 1
[ 1.680000] rtc-rs5c372 0-0032: setting system clock to 2012-07-18
13:42:45 UTC (1342618965)
[ 1.690000] Initalizing network drop monitor service
[ 1.700000] Freeing init memory: 112K
Loading, please wait...
[ 1.960000] udev[39]: starting version 164
[ 2.940000] SCSI subsystem initialized
[ 3.230000] scsi0 : sata_vsc
[ 3.240000] scsi1 : sata_vsc
[ 3.240000] scsi2 : sata_vsc
[ 3.250000] scsi3 : sata_vsc
[ 3.250000] ata1: SATA max UDMA/133 mmio m4096@0x80060000 port 0x80060200
irq 29
[ 3.270000] ata2: SATA max UDMA/133 mmio m4096@0x80060000 port 0x80060400
irq 29
[ 3.270000] ata3: SATA max UDMA/133 mmio m4096@0x80060000 port 0x80060600
irq 29
[ 3.280000] ata4: SATA max UDMA/133 mmio m4096@0x80060000 port 0x80060800
irq 29
[ 3.640000] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 3.660000] ata1.00: ATA-8: WDC WD5000AAKS-00UU3A0, 01.03B01, max
UDMA/133
[ 3.660000] ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[ 3.690000] ata1.00: configured for UDMA/133
[ 3.690000] scsi 0:0:0:0: Direct-Access ATA WDC WD5000AAKS-0
01.0 PQ: 0 ANSI: 5
[ 4.050000] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 4.070000] ata2.00: ATA-8: WDC WD5000AAKS-00V1A0, 05.01D05, max UDMA/133
[ 4.070000] ata2.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[ 4.100000] ata2.00: configured for UDMA/133
[ 4.100000] scsi 1:0:0:0: Direct-Access ATA WDC WD5000AAKS-0
05.0 PQ: 0 ANSI: 5
[ 4.460000] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 4.480000] ata3.00: ATA-8: WDC WD5000AAKS-00E4A0, 05.01D05, max UDMA/133
[ 4.480000] ata3.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[ 4.510000] ata3.00: configured for UDMA/133
[ 4.510000] scsi 2:0:0:0: Direct-Access ATA WDC WD5000AAKS-0
05.0 PQ: 0 ANSI: 5
[ 4.870000] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 4.890000] ata4.00: ATA-8: WDC WD5000AAKS-22V1A0, 05.01D05, max UDMA/133
[ 4.890000] ata4.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[ 4.920000] ata4.00: configured for UDMA/133
[ 4.920000] scsi 3:0:0:0: Direct-Access ATA WDC WD5000AAKS-2
05.0 PQ: 0 ANSI: 5
[ 5.100000] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500
GB/465 GiB)
[ 5.110000] sd 0:0:0:0: [sda] Write Protect is off
[ 5.120000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 5.130000] sda:
[ 5.130000] sd 1:0:0:0: [sdb] 976773168 512-byte logical blocks: (500
GB/465 GiB)
[ 5.150000] sd 2:0:0:0: [sdc] 976773168 512-byte logical blocks: (500
GB/465 GiB)
[ 5.150000] sd 2:0:0:0: [sdc] Write Protect is off
[ 5.160000] sda1 sda2 sda3 <
[ 5.160000] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 5.180000] sd 3:0:0:0: [sdd] 976773168 512-byte logical blocks: (500
GB/465 GiB)
[ 5.190000] sd 1:0:0:0: [sdb] Write Protect is off
[ 5.190000] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 5.210000] sda5 >
[ 5.230000] sd 0:0:0:0: [sda] Attached SCSI disk
[ 5.230000] sd 3:0:0:0: [sdd] Write Protect is off
[ 5.250000] sdc: sdc1
[ 5.280000] sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 5.290000] sdb: sdb1
[ 5.310000] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 5.320000] sd 2:0:0:0: [sdc] Attached SCSI disk
[ 5.370000] sdd: sdd1
[ 5.390000] sd 3:0:0:0: [sdd] Attached SCSI disk
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ...
Begin: Loading[ 6.450000] md: linear personality registered for level -1
Success: loaded module linear.
done.
Begin: Assembling all MD arrays ... [ 6.500000] mdadm: sending ioctl 1261
to a partition!
[ 6.510000] mdadm: sending ioctl 1261 to a partition!
[ 6.510000] mdadm: sending ioctl 1261 to a partition!
[ 6.520000] mdadm: sending ioctl 1261 to a partition!
[ 6.530000] mdadm: sending ioctl 1261 to a partition!
[ 6.530000] mdadm: sending ioctl 1261 to a partition!
[ 6.540000] mdadm: sending ioctl 1261 to a partition!
[ 6.540000] mdadm: sending ioctl 1261 to a partition!
[ 6.550000] mdadm: sending ioctl 1261 to a partition!
[ 6.550000] mdadm: sending ioctl 1261 to a partition!
[ 6.600000] md: md0 stopped.
[ 6.680000] md: bind<sdc1>
[ 6.680000] md: bind<sdd1>
[ 6.680000] md: bind<sdb1>
[ 6.780000] md0: detected capacity change from 0 to 1500320342016
mdadm: /dev/md0 has been started with 3 drives.
Success: assembled all arrays.
done.
done.
[ 6.850000] md0: unknown partition table
Begin: Running /scripts/local-premount ... done.
[ 7.310000] kjournald starting. Commit interval 5 seconds
[ 7.320000] EXT3 FS on sda2, internal journal
[ 7.330000] EXT3-fs: mounted filesystem with ordered data mode.
Begin: Running /scripts/local-bottom ... done.
done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.88 booting
Using makefile-style concurrent boot in runlevel S.
Starting the hotplug events dispatcher: udevd[ 9.170000] udev[182]:
starting version 164
.
Synthesizing the initial hotplug events...done.
Waiting for /dev to be fully populated...[ 10.640000] Intel(R) PRO/1000
Network Driver - version 7.3.21-k5-NAPI
[ 10.640000] Copyright (c) 1999-2006 Intel Corporation.
[ 11.050000] e1000: 0000:00:01.0: e1000_probe: (PCI:33MHz:32-bit)
00:02:41:00:94:7f
[ 11.860000] usbcore: registered new interface driver usbfs
[ 11.870000] usbcore: registered new interface driver hub
[ 11.880000] usbcore: registered new device driver usb
[ 12.000000] __ratelimit: 48 callbacks suppressed
[ 12.010000] mdadm: sending ioctl 1261 to a partition!
[ 12.010000] mdadm: sending ioctl 1261 to a partition!
[ 12.020000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 12.140000] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network
Connection
[ 12.150000] ehci_hcd 0000:00:05.2: EHCI Host Controller
[ 12.150000] ehci_hcd 0000:00:05.2: new USB bus registered, assigned bus
number 1
[ 12.170000] ehci_hcd 0000:00:05.2: Enabling legacy PCI PM
[ 12.210000] ehci_hcd 0000:00:05.2: irq 27, io mem 0x80063000
[ 12.230000] ehci_hcd 0000:00:05.2: USB 2.0 started, EHCI 1.00
[ 12.230000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 12.240000] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 12.250000] usb usb1: Product: EHCI Host Controller
[ 12.250000] usb usb1: Manufacturer: Linux 2.6.32-5-iop32x ehci_hcd
[ 12.260000] usb usb1: SerialNumber: 0000:00:05.2
[ 12.330000] usb usb1: configuration #1 chosen from 1 choice
[ 12.330000] hub 1-0:1.0: USB hub found
[ 12.350000] hub 1-0:1.0: 5 ports detected
[ 12.430000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 12.450000] ohci_hcd 0000:00:05.0: OHCI Host Controller
[ 12.450000] ohci_hcd 0000:00:05.0: new USB bus registered, assigned bus
number 2
[ 12.470000] ohci_hcd 0000:00:05.0: irq 30, io mem 0x80061000
[ 12.580000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 12.580000] usb usb2: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 12.590000] usb usb2: Product: OHCI Host Controller
[ 12.590000] usb usb2: Manufacturer: Linux 2.6.32-5-iop32x ohci_hcd
[ 12.610000] usb usb2: SerialNumber: 0000:00:05.0
[ 12.610000] usb usb2: configuration #1 chosen from 1 choice
[ 12.610000] hub 2-0:1.0: USB hub found
[ 12.620000] hub 2-0:1.0: 3 ports detected
[ 12.620000] ohci_hcd 0000:00:05.1: OHCI Host Controller
[ 12.630000] ohci_hcd 0000:00:05.1: new USB bus registered, assigned bus
number 3
[ 12.650000] ohci_hcd 0000:00:05.1: irq 29, io mem 0x80062000
[ 12.770000] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 12.770000] usb usb3: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 12.780000] usb usb3: Product: OHCI Host Controller
[ 12.780000] usb usb3: Manufacturer: Linux 2.6.32-5-iop32x ohci_hcd
[ 12.790000] usb usb3: SerialNumber: 0000:00:05.1
[ 12.830000] usb usb3: configuration #1 chosen from 1 choice
[ 12.830000] hub 3-0:1.0: USB hub found
[ 12.850000] hub 3-0:1.0: 2 ports detected
done.
Activating swap...[ 13.520000] Adding 748536k swap on /dev/sda5.
Priority:-1 extents:1 across:748536k
done.
Checking root file system...fsck from util-linux-ng 2.17.2
e2fsck 1.41.12 (17-May-2010)
/dev/sda2: clean, 50272/30466048 files, 2165685/121846528 blocks (check
after next mount)
done.
[ 14.860000] EXT3 FS on sda2, internal journal
[ 15.380000] loop: module loaded
Cleaning up ifupdown....
Loading kernel modules...done.
Generating udev events for MD arrays...done.
Setting up networking...[ 15.660000] mdadm: sending ioctl 1261 to a
partition!
[ 15.660000] mdadm: sending ioctl 1261 to a partition!
.
Activating lvm and md swap...done.
Checking file systems...fsck from util-linux-ng 2.17.2
e2fsck 1.41.12 (17-May-2010)
/dev/sda1: clean, 17/124496 files, 20606/248832 blocks
done.
Mounting local filesystems...[ 17.300000] kjournald starting. Commit
interval 5 seconds
[ 17.310000] EXT3 FS on md0, internal journal
[ 17.320000] EXT3-fs: mounted filesystem with ordered data mode.
done.
Activating swapfile swap...done.
Cleaning up temporary files....
Setting kernel variables ...done.
Configuring network interfaces...[ 18.470000] e1000: eth0 NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
done.
Starting portmap daemon....
Starting NFS common utilities: statd.
Cleaning up temporary files....
INIT: Entering runlevel: 2
Using makefile-style concurrent boot in runlevel 2.
Starting NFS common utilities: statd.
Starting portmap daemon...Already running..
Starting enhanced syslogd: rsyslogd.
Starting deferred execution scheduler: atd.
Starting periodic command scheduler: cron.
Starting system message bus: dbus.
Starting MTA:Starting MD monitoring service: mdadm --monitor.
[ 25.980000] NET: Registered protocol family 10
Starting Samba daemons: nmbd smbd.
exim4.
Starting OpenBSD Secure Shell server: sshd.
Debian GNU/Linux 6.0 Freestor ttyS0
Freestor login:
--log end--
-----Original Message-----
From: JF Straeten [mailto:jfstraeten@scarlet.be]
Sent: Wednesday, July 18, 2012 4:15 AM
To: debian-arm@lists.debian.org
Subject: Re: SS4000E Fan speed, LEDS and power button
Chris,
On Tue, Jul 17, 2012 at 09:26:53PM -0400, Chris Wilkinson wrote:
> I have 4 disks so I had wanted to use all 4 in a RAID5 array.
Doable ; it's the setup I have on mine.
> I think the mistake was not to select manual partitioning in d-i.
Yes ;)
> I wonder if there is a way to re-run d-i from scratch with the
> existing Debian on the HDs.? It boots straight into Debian after
> fixing the fis boot script as it should. I have no data yet so this
> would not be a problem.
You can try the < rescue mode > which does exactly that...
You should append < rescue/enable=true > to the exec line for this.
So the exec line becomes :
exec -c "console=ttyS0,115200 root=/dev/ram mem=256M@0xa0000000
rescue/enable=true" -r 0x01800000
> There is no driver for the w83792*?
It's a loadable module :
lothar:~# modinfo w83792d
filename: /lib/modules/2.6.32-5-iop32x/kernel/drivers/hwmon/w83792d.ko
[...]
Hih,
--
JFS.
--
To UNSUBSCRIBE, email to debian-arm-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact
listmaster@lists.debian.org
Archive: 20120718081513.GA3350@jones.jfs.dt">http://lists.debian.org/20120718081513.GA3350@jones.jfs.dt
Reply to: