[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

pppoe on pure64 sid

I just got done installing pure64 on my new box, kde3.3, mozilla,
everything works smooth, except that I can't get on the internet,
which is strange because I did a netinstall. During the install I was
able to set up pppoe, and then that's how I downloaded the whole
system. Let aptitude run all night basically.

Well, after a couple of reboots, it won't work anymore. More precisely
after I do pon dsl-provider here is what ifconfig says.

eth1      Lien encap:Ethernet  HWaddr 00:11:09:7C:9D:A5
          adr inet6: fe80::211:9ff:fe7c:9da5/64 Scope:Lien
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:5256 errors:0 dropped:0 overruns:0 frame:0
          TX packets:2884 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 lg file transmission:1000
          RX bytes:358232 (349.8 KiB)  TX bytes:101777 (99.3 KiB)
          Interruption:10 Adresse de base:0x7000

lo        Lien encap:Boucle locale
          inet adr:127.0.0.1  Masque:255.0.0.0
          adr inet6: ::1/128 Scope:Hôte
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:678 errors:0 dropped:0 overruns:0 frame:0
          TX packets:678 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 lg file transmission:0
          RX bytes:45068 (44.0 KiB)  TX bytes:45068 (44.0 KiB)

ppp0      Lien encap:Protocole Point-à-Point
          inet adr:83.113.225.163  P-t-P:193.253.160.3  Masque:255.255.255.255
          UP POINTOPOINT RUNNING NOARP MULTICAST  MTU:1492  Metric:1
          RX packets:7 errors:0 dropped:0 overruns:0 frame:0
          TX packets:3 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 lg file transmission:3
          RX bytes:246 (246.0 b)  TX bytes:54 (54.0 b)



Here's what route gives

Table de routage IP du noyau
Destination     Passerelle      Genmask         Indic Metric Ref    Use Iface
193.253.160.3   *               255.255.255.255 UH    0      0        0 ppp0
default         193.253.160.3   0.0.0.0         UG    0      0        0 ppp0

Here's what ps aux | grep ppp gives

root     13928  0.0  0.3 14984 1592 ?        Ss   17:16   0:00
/usr/sbin/pppd call dsl-provider
root     14250  0.0  0.1  5152  836 pts/1    R+   17:18   0:00 grep ppp

Here's what plog gives

Nov 19 17:19:08 localhost pppd[14302]: Couldn't increase MRU to 1500
Nov 19 17:19:08 localhost pppd[14302]: Couldn't increase MRU to 1500
Nov 19 17:19:08 localhost pppd[14302]: CHAP authentication succeeded
Nov 19 17:19:08 localhost pppd[14302]: peer from calling number
00:90:1A:41:04:2E authorized
Nov 19 17:19:08 localhost pppd[14302]: Cannot determine ethernet
address for proxy ARP
Nov 19 17:19:08 localhost pppd[14302]: local  IP address 81.251.89.62
Nov 19 17:19:08 localhost pppd[14302]: remote IP address 193.253.160.3
Nov 19 17:19:08 localhost pppd[14302]: primary   DNS address 80.10.246.130
Nov 19 17:19:08 localhost pppd[14302]: secondary DNS address 80.10.246.3


What is very strange is that I can ping stuff, but only by IP address.
For example ping www.google.com doesn't work. Also kmail and mozilla
won't connect to anything.

Here's my interfaces file

# The loopback network interface
auto lo
iface lo inet loopback

Here is my /etc/ppp/peers/dsl-provider file

# Configuration file for PPP, using PPP over Ethernet 
# to connect to a DSL provider.
#
# See the manual page pppd(8) for information on all the options.

##
# Section 1
#
# Stuff to configure...

# MUST CHANGE: Uncomment the following line, replacing the user@provider.net
# by the DSL user name given to your by your DSL provider.
# (There should be a matching entry in /etc/ppp/pap-secrets with the password.)
#user myusername@myprovider.net

# Use the pppoe program to send the ppp packets over the Ethernet link
# This line should work fine if this computer is the only one accessing
# the Internet through this DSL connection. This is the right line to use
# for most people.
#pty "/usr/sbin/pppoe -I eth1 -T 80 -m 1452"

# An even more conservative version of the previous line, if things
# don't work using -m 1452... 
pty "/usr/sbin/pppoe -I eth1 -T 80 -m 1412"

# If the computer connected to the Internet using pppoe is not being used
# by other computers as a gateway to the Internet, you can try the following
# line instead, for a small gain in speed:
#pty "/usr/sbin/pppoe -I eth0 -T 80"


# The following two options should work fine for most DSL users.

# Assumes that your IP address is allocated dynamically
# by your DSL provider...
noipdefault
# Try to get the name server addresses from the ISP.
usepeerdns
# Use this connection as the default route.
# Comment out if you already have the correct default route installed.
defaultroute

##
# Section 2
#
# Uncomment if your DSL provider charges by minute connected
# and you want to use demand-dialing. 
#
# Disconnect after 300 seconds (5 minutes) of idle time.

#demand
#idle 300

##
# Section 3
#
# You shouldn't need to change these options...

hide-password
lcp-echo-interval 20
lcp-echo-failure 3
# Override any connect script that may have been set in /etc/ppp/options.
connect /bin/true
noauth
persist
mtu 1492

# RFC 2516, paragraph 7 mandates that the following options MUST NOT be
# requested and MUST be rejected if requested by the peer:
# Address-and-Control-Field-Compression (ACFC)
noaccomp
# Asynchronous-Control-Character-Map (ACCM)
default-asyncmap

plugin rp-pppoe.so eth1


user "fti/q9tdaep@fti"



I am stumped. Please help.

Alex Cabuz.
Reply to: