Re: CDRECORD PROBLEM ?
On Tue, 2004-09-28 at 14:33 +0200, Joerg Schilling wrote:
> Sasa Ostrouska <sasa.ostrouska@volja.net> wrote:
>
> > Hello to everybody,
> >
> > I tried to burn a DVD and I got this error, can somebody tell me
> > what is on ? Is a brocen media ?
> >
> >
> > Calling: /usr/lib/xcdroast-0.98/bin/xcdrwrap CDRECORDPRODVD dev= "0,0,0"
> > gracetime=10 fs=4096k -v driveropts=burnfree speed=16 -dao -eject -pad
> > -waiti tsize=2107292s -
> >
> > scsidev: '0,0,0'
> > scsibus: 0 target: 0 lun: 0
> > Linux sg driver version: 3.1.25
> > SCSI buffer size: 64512
> > Cdrecord-ProDVD-Clone 2.01b31 (i686-pc-linux-gnu) Copyright (C)
> > 1995-2004 Jörg Schilling
> > Unlocked features: ProDVD Clone
> > Limited features:
> > This copy of cdrecord is licensed for:
> > private/research/educational_non-commercial_use
> > TOC Type: 1 = CD-ROM
> > Waiting for data on stdin...
> > Using libscg version 'schily-0.8'.
> > Driveropts: 'burnfree'
> > atapi: 1
> > Device type : Removable CD-ROM
> > Version : 0
> > Response Format: 2
> > Capabilities :
> > Vendor_info : 'PIONEER '
> > Identifikation : 'DVD-RW DVR-K12D'
> > Revision : '1.00'
> > Device seems to be: Generic mmc2 DVD-R/DVD-RW.
> > Current: DVD+R
> > Profile: DVD+R (current)
> > Profile: DVD+RW
> > Profile: DVD-RW sequential overwrite
> > Profile: DVD-RW restricted overwrite
> > Profile: DVD-R sequential recording
> > Profile: DVD-ROM
> > Profile: CD-RW
> > Profile: CD-R
> > Profile: CD-ROM
> > Using generic SCSI-3/mmc-3 DVD+R driver (mmc_dvdplusr).
> > Driver flags : DVD MMC-3 SWABAUDIO BURNFREE
> > Supported modes: PACKET SAO
> > Drive buf size : 1605632 = 1568 KB
> > FIFO size : 4194304 = 4096 KB
> > Track 01: data 4115 MB padsize: 30 KB
> > Total size: 4115 MB = 2107307 sectors
> > Current Secsize: 2048
> > Blocks total: 2295104 Blocks current: 2295104 Blocks remaining: 187797
> > Starting to write CD/DVD at speed 2 in real SAO mode for single session.
> >
> > Waiting for reader process to fill input buffer ...
> > input buffer ready.
> > Starting new track at sector: 0
> > cdrecord.prodvd: Input/output error. write_g1: scsi sendcmd: no error
> > CDB: 2A 00 00 07 2A 54 00 00 1F 00
> > status: 0x2 (CHECK CONDITION)
> > Sense Bytes: 70 00 04 00 13 00 02 0E 26 01 31 E6 08 01 00 00
> > Sense Key: 0x4 Hardware Error, Segment 0
> > Sense Code: 0x08 Qual 0x01 (logical unit communication time-out) Fru 0x0
> > Sense flags: Blk 1245186 (not valid)
> > cmd finished after 2.012s timeout 100s
> > cdrecord.prodvd: A write error occured.
> > cdrecord.prodvd: Please properly read the error message above.
>
> Caused either by incorrect kernel DMA setup or by a defective kernel.
>
> Jörg
>
Yesterday I wonted to write a DVD butit ended with a different error
after few sec.of writing. I think this is as I have the kernel 2.6.8.1
Am I correct ?
I saw that there are some problems with that kernel.
Do you have any suggestions. I can use the 2.4.27 kernel
without the ide-scsi thing as this is the only way I can write
the DVD's - for the CD's ide-scsi works OK.
If it is a pach for the 2.6.8.1 kernel where is possible to get it ?
Thanks for your time and best regards
--
Sasa Ostrouska <sasa.ostrouska@volja.net>
Reply to: