Bug#464661: xserver-xorg-video-intel: Couldn't bind memory for ring buffer with kernel 2.6.24
Am Freitag, 8. Februar 2008 schrieben Sie:
> Are the agp and drm modules loaded as usual? Is there anything
> interesting in dmesg? The upstream dev said there were some changes in
I attached the dmesg output with a vanilla kernel 2.6.23-rc6 (not 2.6.23, as I
wrote before) in dmesg.working and dmesg output with Debian kernel 2.6.24 in
dmesg. They differ in the agp part.
> the support for low memory situation. If modules are correctly loaded
Hmmm, the computer is a set top box with only 128 MB of memory.
> and dmesg looks ok, we'll forward the bug upstream at
> bugzilla.freedesktop.org.
Maybe it is related to this bug:
http://kerneltrap.org/mailarchive/linux-kernel/2007/10/5/330704
regards,
Jörg
--
PGP Key: send mail with subject 'SEND PGP-KEY' PGP Key-ID: FD 4E 21 1D
PGP Fingerprint: 388A872AFC5649D3 BCEC65778BE0C605
Initializing cgroup subsys cpuset
Linux version 2.6.24-1-686 (Debian 2.6.24-2) (waldi@debian.org) (gcc version 4.1.3 20080114 (prerelease) (Debian 4.1.2-19)) #1 SMP Thu Jan 31 20:35:50 UTC 2008
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000077d0000 (usable)
BIOS-e820: 00000000077d0000 - 00000000077df000 (ACPI data)
BIOS-e820: 00000000077df000 - 0000000007800000 (ACPI NVS)
0MB HIGHMEM available.
119MB LOWMEM available.
Entering add_active_range(0, 0, 30672) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 30672
HighMem 30672 -> 30672
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 30672
On node 0 totalpages: 30672
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 207 pages used for memmap
Normal zone: 26369 pages, LIFO batch:7
HighMem zone: 0 pages used for memmap
Movable zone: 0 pages used for memmap
DMI 2.3 present.
ACPI: RSDP 000F5800, 0014 (r0 ACPIAM)
ACPI: RSDT 077D0000, 002C (r1 A M I OEMRSDT 12000526 MSFT 97)
ACPI: FACP 077D0200, 0081 (r2 A M I OEMFACP 12000526 MSFT 97)
ACPI: DSDT 077D0390, 2B04 (r1 0AHMM 0AHMM109 109 INTL 2002026)
ACPI: FACS 077DF000, 0040
ACPI: OEMB 077DF040, 0040 (r1 A M I AMI_OEM 12000526 MSFT 97)
ACPI: PM-Timer IO Port: 0x408
Allocating PCI resources starting at 10000000 (gap: 07800000:f8800000)
swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e0000
swsusp: Registered nosave memory region: 00000000000e0000 - 0000000000100000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 30433
Kernel command line: root=LABEL=ROOT ro panic=10 acpi_pm_good hpet=force
Found and enabled local APIC!
mapped APIC to ffffb000 (fee00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 512 (order: 9, 2048 bytes)
Detected 730.902 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 112648k/122688k available (1785k kernel code, 9504k reserved, 715k data, 248k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xfff4c000 - 0xfffff000 ( 716 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xc8000000 - 0xff7fe000 ( 887 MB)
lowmem : 0xc0000000 - 0xc77d0000 ( 119 MB)
.init : 0xc0377000 - 0xc03b5000 ( 248 kB)
.data : 0xc02be755 - 0xc0371384 ( 715 kB)
.text : 0xc0100000 - 0xc02be755 (1785 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 1463.33 BogoMIPS (lpj=2926672)
Security Framework initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
CPU: After generic identify, caps: 0383fbff 00000000 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After all inits, caps: 0383fbff 00000000 00000000 00000040 00000000 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 11k freed
ACPI: Core revision 20070126
ACPI: setting ELCR to 0200 (from 0ea0)
CPU0: Intel Mobile Intel(R) Celeron(TM) CPU 733MHz stepping 04
SMP motherboard not detected.
Brought up 1 CPUs
net_namespace: 64 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
Force enabled HPET at base address 0xfed00000
PCI quirk: region 0400-047f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 0500-053f claimed by ICH4 GPIO
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 *7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - 82, should be 7F [20070126]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 15 devices
ACPI: ACPI bus type pnp unregistered
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NET: Registered protocol family 8
NET: Registered protocol family 20
hpet clockevent registered
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 64-bit timers, 14318180 Hz
ACPI: RTC can wake from S4
Time: tsc clocksource has been installed.
system 00:07: ioport range 0x4d0-0x4d1 has been reserved
system 00:07: ioport range 0x400-0x47f has been reserved
system 00:07: ioport range 0x500-0x53f has been reserved
system 00:09: iomem range 0xffc00000-0xfff7ffff has been reserved
system 00:0a: iomem range 0x0-0x0 could not be reserved
system 00:0a: iomem range 0x0-0x0 could not be reserved
system 00:0d: ioport range 0xa00-0xa3f has been reserved
system 00:0e: iomem range 0x0-0x9ffff could not be reserved
system 00:0e: iomem range 0xc0000-0xdffff could not be reserved
system 00:0e: iomem range 0xe0000-0xfffff could not be reserved
system 00:0e: iomem range 0x100000-0x77fffff could not be reserved
system 00:0e: iomem range 0x0-0x0 could not be reserved
PCI: Bridge: 0000:00:1e.0
IO window: d000-dfff
MEM window: ff700000-ff7fffff
PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
checking if image is initramfs...<7>Switched to high resolution mode on CPU 0
it is
Freeing initrd memory: 5310k freed
audit: initializing netlink socket (disabled)
audit(1202548501.704:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:00:02.0
0000:00:1d.7 EHCI: BIOS handoff failed (BIOS bug ?) 01010001
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:06: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
registered taskstats version 1
Freeing unused kernel memory: 248k freed
ACPI: Processor [CPU1] (supports 8 throttling states)
input: AT Translated Set 2 keyboard as /class/input/input0
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 7
PCI: setting IRQ 7 as level-triggered
ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 7 (level, low) -> IRQ 7
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 7, io base 0x0000e000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 5, io base 0x0000e080
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 9
PCI: setting IRQ 9 as level-triggered
ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 9 (level, low) -> IRQ 9
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 9, io base 0x0000e400
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 1-1: new low speed USB device using uhci_hcd and address 2
usb 1-1: configuration #1 chosen from 1 choice
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [LNKH] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 10, io mem 0xffa7f400
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
usb 1-1: USB disconnect, address 2
SCSI subsystem initialized
libata version 3.00 loaded.
8139too Fast Ethernet driver 0.9.28
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:01:06.0[A] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
eth0: RealTek RTL8139 at 0xd800, 00:02:ff:01:1a:66, IRQ 11
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller (0x8086:0x24cb rev 0x02) at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 9 (level, low) -> IRQ 9
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
usb 4-2: new high speed USB device using ehci_hcd and address 3
usb 4-2: configuration #1 chosen from 1 choice
usbcore: registered new interface driver hiddev
Initializing USB Mass Storage driver...
hda: IEI Global Sourcing - EDC 1GB, ATA DISK drive
hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
usb 1-1: new low speed USB device using uhci_hcd and address 3
usb 1-1: configuration #1 chosen from 1 choice
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
input: Cypress PS/2 to USB Adapter as /class/input/input1
input,hidraw0: USB HID v1.00 Keyboard [Cypress PS/2 to USB Adapter] on usb-0000:00:1d.0-1
input: Cypress PS/2 to USB Adapter as /class/input/input2
input,hidraw1: USB HID v1.00 Mouse [Cypress PS/2 to USB Adapter] on usb-0000:00:1d.0-1
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
hda: max request size: 128KiB
hda: 1997856 sectors (1022 MB) w/1KiB Cache, CHS=1982/16/63
hda: hda1 < hda5 > hda2
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
usb-storage: device scan complete
scsi 0:0:0:0: Direct-Access USB DISK 2.0 PMAP PQ: 0 ANSI: 0 CCS
Linux agpgart interface v0.102
agpgart: Detected an Intel 830M Chipset.
agpgart: Detected 8060K stolen memory.
agpgart: AGP aperture is 128M @ 0xf0000000
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)
iTCO_wdt: Found a ICH4 TCO device (Version=1, TCOBASE=0x0460)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
intel_rng: FWH not detected
input: Power Button (FF) as /class/input/input3
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input4
ACPI: Power Button (CM) [PWRB]
ACPI: PCI Interrupt 0000:00:1f.3[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 52510 usecs
intel8x0: clocking to 48000
Real Time Clock Driver v1.12ac
input: PC Speaker as /class/input/input5
input: PS/2 Generic Mouse as /class/input/input6
ACPI: PCI Interrupt 0000:01:07.0[A] -> Link [LNKD] -> GSI 5 (level, low) -> IRQ 5
Driver 'sd' needs updating - please use bus_type methods
sd 0:0:0:0: [sda] Attached SCSI removable disk
p54: LM86 firmware
p54: FW rev 2.7.0.0 - Softmac protocol 4.1
phy0: Selected rate control algorithm 'simple'
phy0: hwaddr 00:60:b3:e0:5e:2d, isl3890
Adding 124952k swap on /dev/hda5. Priority:-1 extents:1 across:124952k
EXT3 FS on hda2, internal journal
loop: module loaded
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ADDRCONF(NETDEV_UP): wlan0: link is not ready
wlan0: Initial auth_alg=0
wlan0: authenticate with AP 00:0c:41:17:e5:e9
wlan0: RX authentication from 00:0c:41:17:e5:e9 (alg=0 transaction=2 status=0)
wlan0: authenticated
wlan0: associate with AP 00:0c:41:17:e5:e9
wlan0: RX AssocResp from 00:0c:41:17:e5:e9 (capab=0x411 status=0 aid=1)
wlan0: associated
wlan0: switched to short barker preamble (BSSID=00:0c:41:17:e5:e9)
ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
padlock: VIA PadLock not detected.
eth0: link down
ADDRCONF(NETDEV_UP): eth0: link is not ready
wlan0: no IPv6 routers present
[drm] Initialized drm 1.1.0 20060810
[drm] Initialized i915 1.6.0 20060119 on minor 0
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKA] -> GSI 7 (level, low) -> IRQ 7
[drm] Initialized i915 1.6.0 20060119 on minor 1
agpgart: pg_start == 0x00000000,intel_private.gtt_entries == 0x000007df
agpgart: Trying to insert into local/stolen memory
Linux version 2.6.23-rc6 (root@ibm) (gcc version 4.2.1 (Debian 4.2.1-5)) #1 PREEMPT Tue Sep 18 13:02:53 CEST 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000007ed0000 (usable)
BIOS-e820: 0000000007ed0000 - 0000000007edf000 (ACPI data)
BIOS-e820: 0000000007edf000 - 0000000007f00000 (ACPI NVS)
126MB LOWMEM available.
Entering add_active_range(0, 0, 32464) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 32464
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 32464
On node 0 totalpages: 32464
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 221 pages used for memmap
Normal zone: 28147 pages, LIFO batch:7
Movable zone: 0 pages used for memmap
DMI 2.3 present.
ACPI: RSDP 000F5800, 0014 (r0 ACPIAM)
ACPI: RSDT 07ED0000, 002C (r1 A M I OEMRSDT 12000526 MSFT 97)
ACPI: FACP 07ED0200, 0081 (r2 A M I OEMFACP 12000526 MSFT 97)
ACPI: DSDT 07ED0390, 2B04 (r1 0AHMM 0AHMM109 109 INTL 2002026)
ACPI: FACS 07EDF000, 0040
ACPI: OEMB 07EDF040, 0040 (r1 A M I AMI_OEM 12000526 MSFT 97)
ACPI: PM-Timer IO Port: 0x408
Allocating PCI resources starting at 10000000 (gap: 07f00000:f8100000)
swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e0000
swsusp: Registered nosave memory region: 00000000000e0000 - 0000000000100000
Built 1 zonelists in Zone order. Total pages: 32211
Kernel command line: root=LABEL=ROOT ro panic=10 acpi_pm_good hpet=force
Found and enabled local APIC!
mapped APIC to ffffb000 (fee00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c030f000 soft=c030e000
PID hash table entries: 512 (order: 9, 2048 bytes)
Detected 730.942 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 123396k/129856k available (1386k kernel code, 5928k reserved, 535k data, 164k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xfffb5000 - 0xfffff000 ( 296 kB)
vmalloc : 0xc8800000 - 0xfffb3000 ( 887 MB)
lowmem : 0xc0000000 - 0xc7ed0000 ( 126 MB)
.init : 0xc02e2000 - 0xc030b000 ( 164 kB)
.data : 0xc025a878 - 0xc02e0524 ( 535 kB)
.text : 0xc0100000 - 0xc025a878 (1386 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
SLUB: Genslabs=22, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
Calibrating delay using timer specific routine.. 1463.02 BogoMIPS (lpj=2926049)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383fbff 00000000 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After all inits, caps: 0383fbff 00000000 00000000 00000040 00000000 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
CPU: Intel Mobile Intel(R) Celeron(TM) CPU 733MHz stepping 04
Checking 'hlt' instruction... OK.
ACPI: Core revision 20070126
ACPI: setting ELCR to 0200 (from 0ea0)
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3)
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI quirk: region 0400-047f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 0500-053f claimed by ICH4 GPIO
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 *7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - 16, should be 13 [20070126]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 15 devices
ACPI: ACPI bus type pnp unregistered
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
ACPI: RTC can wake from S4
Time: tsc clocksource has been installed.
pnp: 00:09: iomem range 0xffc00000-0xfff7ffff has been reserved
pnp: 00:0a: iomem range 0x0-0x0 could not be reserved
pnp: 00:0a: iomem range 0x0-0x0 could not be reserved
pnp: 00:0d: ioport range 0xa00-0xa3f has been reserved
pnp: 00:0e: iomem range 0x0-0x9ffff could not be reserved
pnp: 00:0e: iomem range 0xc0000-0xdffff could not be reserved
pnp: 00:0e: iomem range 0xe0000-0xfffff could not be reserved
pnp: 00:0e: iomem range 0x100000-0x7efffff could not be reserved
PCI: Bridge: 0000:00:1e.0
IO window: d000-dfff
MEM window: ff700000-ff7fffff
PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
checking if image is initramfs... it is
Switched to high resolution mode on CPU 0
Freeing initrd memory: 2498k freed
Total HugeTLB memory allocated, 0
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler cfq registered (default)
Boot video device is 0000:00:02.0
0000:00:1d.7 EHCI: BIOS handoff failed (BIOS bug ?) 01010001
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
Using IPI Shortcut mode
Freeing unused kernel memory: 164k freed
NET: Registered protocol family 1
ACPI: Processor [CPU1] (supports 8 throttling states)
input: AT Translated Set 2 keyboard as /class/input/input0
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
8139too Fast Ethernet driver 0.9.28
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:01:06.0[A] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
eth0: RealTek RTL8139 at 0xc8824c00, 00:02:ff:01:1a:66, IRQ 11
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 7
PCI: setting IRQ 7 as level-triggered
ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 7 (level, low) -> IRQ 7
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 7, io base 0x0000e000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
SCSI subsystem initialized
libata version 2.21 loaded.
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 5, io base 0x0000e080
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 9
PCI: setting IRQ 9 as level-triggered
ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 9 (level, low) -> IRQ 9
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 9, io base 0x0000e400
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [LNKH] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 10, io mem 0xffa7f400
usb 1-1: new low speed USB device using uhci_hcd and address 2
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
ata_piix 0000:00:1f.1: version 2.12
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 9 (level, low) -> IRQ 9
PCI: Setting latency timer of device 0000:00:1f.1 to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: PATA max UDMA/100 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001ffa0 irq 14
ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001ffa8 irq 15
ata1.00: ATA-0: IEI Global Sourcing - EDC 1GB, ra04.00d, max PIO4
ata1.00: 1997856 sectors, multi 0: LBA
ata1.00: configured for PIO4
scsi 0:0:0:0: Direct-Access ATA IEI Global Sourc ra04 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 1997856 512-byte hardware sectors (1023 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 1997856 512-byte hardware sectors (1023 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 < sda5 > sda2
sd 0:0:0:0: [sda] Attached SCSI disk
usb 1-1: new low speed USB device using uhci_hcd and address 3
usb 1-1: configuration #1 chosen from 1 choice
usbcore: registered new interface driver hiddev
input: Cypress PS/2 to USB Adapter as /class/input/input1
input: USB HID v1.00 Keyboard [Cypress PS/2 to USB Adapter] on usb-0000:00:1d.0-1
input: Cypress PS/2 to USB Adapter as /class/input/input2
input: USB HID v1.00 Mouse [Cypress PS/2 to USB Adapter] on usb-0000:00:1d.0-1
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
Attempting manual resume
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
input: PC Speaker as /class/input/input3
Linux agpgart interface v0.102
agpgart: Detected an Intel 830M Chipset.
agpgart: No pre-allocated video memory detected.
agpgart: AGP aperture is 128M @ 0xf0000000
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:06: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
input: Power Button (FF) as /class/input/input4
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input5
ACPI: Power Button (CM) [PWRB]
ACPI: PCI Interrupt 0000:00:1f.3[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 52558 usecs
intel8x0: clocking to 48000
ACPI: PCI Interrupt 0000:01:07.0[A] -> Link [LNKD] -> GSI 5 (level, low) -> IRQ 5
p54: LM86 firmware
p54: FW rev 2.7.0.0 - Softmac protocol 4.1
input: PS/2 Generic Mouse as /class/input/input6
wmaster0: Selected rate control algorithm 'simple'
phy0: hwaddr 00:60:b3:e0:5e:2d, isl3890
Adding 124952k swap on /dev/sda5. Priority:-1 extents:1 across:124952k
EXT3 FS on sda2, internal journal
loop: module loaded
NET: Registered protocol family 17
NET: Registered protocol family 10
ADDRCONF(NETDEV_UP): wlan0: link is not ready
wlan0: Initial auth_alg=0
wlan0: authenticate with AP 00:0c:41:17:e5:e9
wlan0: RX authentication from 00:0c:41:17:e5:e9 (alg=0 transaction=2 status=0)
wlan0: authenticated
wlan0: associate with AP 00:0c:41:17:e5:e9
wlan0: RX AssocResp from 00:0c:41:17:e5:e9 (capab=0x411 status=0 aid=1)
wlan0: associated
wlan0: switched to short barker preamble (BSSID=00:0c:41:17:e5:e9)
ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
wlan0: RX WEP frame, but no key set
eth0: link down
ADDRCONF(NETDEV_UP): eth0: link is not ready
wlan0: no IPv6 routers present
[drm] Initialized drm 1.1.0 20060810
[drm] Initialized i915 1.6.0 20060119 on minor 0
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKA] -> GSI 7 (level, low) -> IRQ 7
[drm] Initialized i915 1.6.0 20060119 on minor 1
Reply to: