XFree 4.0.1 phase2v7 on Powermac 7600/132 /chaos/control
Hi again,
I followed Michel's advice and installed nearly flawlessly the XFree 4.0.1
phase2 .debs (it was v7 at the time I tried it).
The only glitche I encountered in the installation was the it didn't
de-install xserver-fbdev_3.3.6 and didn't install xserver-xfree86_4.0.1_0pha
se2v7. But that was simple to correct once detected.
As for the software itself, if it works better than my first experience
with 4.0.1 it still doesn't work properly:
- the powermac 7600/132 /chaos/control graphic device is correctly
detected and the amount of vram is correctly guessed too.
- XFree86 -configure fail: error 11 while testing the different
drivers.
- the X server display is buggy: the display is wrapped around the
screen so that each extremity touch in the center of the screen.
But the xserver doesn't echo any errors whatsoever.
A_______B ____BA___
| | ||
| | ||
D_______C ____CD___
what it usually what i get
look like
So for the time being I reverted to XFree 3.3.6 framebuffer server, but I'll try to see how XFree 4.0.1 works under the 3dfx with the mac roms.
Attached is my XF86Config for XFree 4.0.1
# The ordering of sections is not important in version 4.0 and later.
# **********************************************************************
# Files section. This allows default font and rgb paths to be set
# **********************************************************************
Section "Files"
# The location of the RGB database. Note, this is the name of the
# file minus the extension (like ".txt" or ".db"). There is normally
# no need to change the default.
RgbPath "/usr/X11R6.4/lib/X11/rgb"
# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
FontPath "/usr/X11R6/lib/X11/fonts/local/"
FontPath "/usr/X11R6/lib/X11/fonts/misc/"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi/:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/100dpi/:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/Type1/"
FontPath "/usr/X11R6/lib/X11/fonts/CID/"
FontPath "/usr/X11R6/lib/X11/fonts/Speedo/"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi/"
FontPath "/usr/X11R6/lib/X11/fonts/100dpi/"
# ModulePath can be used to set a search path for the X server modules.
# The default path is shown here.
# ModulePath "/usr/X11R6/lib/modules"
EndSection
# **********************************************************************
# Module section -- this is an optional section which is used to specify
# which run-time loadable modules to load when the X server starts up.
# **********************************************************************
Section "Module"
# This loads the DBE extension module.
Load "extmod"
Load "dbe"
# This loads the miscellaneous extensions module, and disables
# Option "suspend time" "30"
# Option "off time" "60"
# Option "EstimateSizesAggresively" "0"
EndSection
# **********************************************************************
# Core keyboard's InputDevice section
# **********************************************************************
Section "InputDevice"
Identifier "Apple Extended ADB"
Driver "keyboard"
Option "AutoRepeat" "500 5"
Option "XkbKeycodes" "macintosh"
Option "XkbGeometry" "macintosh"
Option "XkbSymbols" "macintosh/fr(extended)"
EndSection
# **********************************************************************
# Core Pointer's InputDevice section
# **********************************************************************
Section "InputDevice"
Identifier "ADB Mouse"
Driver "mouse"
Option "Protocol" "BusMouse"
Option "Device" "/dev/adbmouse"
EndSection
# **********************************************************************
# Monitor section
# **********************************************************************
# Any number of monitor sections may be present
Section "Monitor"
Identifier "Sony CDP-200SFT"
HorizSync 31-80
VertRefresh 50-120
# If a monitor has DPMS support, that can be indicated here. This will
# enable DPMS when the montor is used with drivers that support it.
Option "dpms"
EndSection
# **********************************************************************
# Graphics device section
# **********************************************************************
# Any number of graphics device sections may be present
Section "Device"
Identifier "Chaos Control"
Driver "fbdev"
EndSection
Section "Device"
Identifier "3dfx Voodoo 3 2000"
Driver "tdfx"
BusID "PCI:0:15:0"
EndSection
# **********************************************************************
# Screen sections.
# **********************************************************************
Section "Screen"
Identifier "chaos"
Device "Chaos Control"
Monitor "Sony CDP-200SFT"
SubSection "Display"
Depth 8
EndSubsection
SubSection "Display"
Depth 16
EndSubsection
SubSection "Display"
Depth 24
EndSubsection
SubSection "Display"
Depth 32
EndSubsection
EndSection
Frédéric Séraphine
Tel: 476 61 53 85 - Fax: 476 61 52 07
INRIA Rhone-Alpes - ZIRST - 655 Avenue de l'Europe - Montbonnot
38334 Saint Ismier Cedex - France
Reply to: