Re: Sata Hard drive testing
Here are the results, of my smartctl test:
I am trying to parse them myself, to see if I can learn anything. But,
immediate glance
and queries did not reveal anything that could help me determine if the
drive is good or not.
smartctl 6.6 2017-11-05 r4594 [x86_64-linux-4.19.0-18-amd64] (local build)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: ST8000DM004-2CX188
Serial Number: ZCT1706V
LU WWN Device Id: 5 000c50 0c2b1cd83
Firmware Version: 0001
User Capacity: 8,001,563,222,016 bytes [8.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5425 rpm
Form Factor: 3.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-3 T13/2161-D revision 5
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Wed Oct 20 14:36:49 2021 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test
routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x73) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 987) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x30a5) SCT Status supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED
WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 064 051 006 Pre-fail
Always - 7226480
3 Spin_Up_Time 0x0003 093 091 000 Pre-fail
Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age
Always - 361
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail
Always - 0
7 Seek_Error_Rate 0x000f 080 060 045 Pre-fail
Always - 104115990
9 Power_On_Hours 0x0032 084 084 000 Old_age
Always - 14558 (99 41 0)
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail
Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age
Always - 77
183 Runtime_Bad_Block 0x0032 095 095 000 Old_age
Always - 5
184 End-to-End_Error 0x0032 100 100 099 Old_age
Always - 0
187 Reported_Uncorrect 0x0032 001 001 000 Old_age
Always - 1334
188 Command_Timeout 0x0032 100 100 000 Old_age
Always - 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age
Always - 0
190 Airflow_Temperature_Cel 0x0022 070 052 040 Old_age
Always - 30 (Min/Max 28/33)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age
Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age
Always - 25
193 Load_Cycle_Count 0x0032 099 099 000 Old_age
Always - 3362
194 Temperature_Celsius 0x0022 030 048 000 Old_age
Always - 30 (0 16 0 0 0)
195 Hardware_ECC_Recovered 0x001a 069 064 000 Old_age
Always - 7226480
197 Current_Pending_Sector 0x0012 100 100 000 Old_age
Always - 8
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age
Offline - 8
199 UDMA_CRC_Error_Count 0x003e 200 198 000 Old_age
Always - 15
240 Head_Flying_Hours 0x0000 100 253 000 Old_age
Offline - 2368 (67 0 0)
241 Total_LBAs_Written 0x0000 100 253 000 Old_age
Offline - 54984038154
242 Total_LBAs_Read 0x0000 100 253 000 Old_age
Offline - 185155335586
SMART Error Log Version: 1
ATA Error Count: 1334 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1334 occurred at disk power-on lifetime: 10525 hours (438 days +
13 hours)
When the command that caused the error occurred, the device was active
or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 53 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 ff ff ff 4f 00 15d+00:06:46.256 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 15d+00:06:46.247 SET FEATURES [Enable SATA
feature]
27 00 00 00 00 00 e0 00 15d+00:06:46.220 READ NATIVE MAX ADDRESS EXT
[OBS-ACS-3]
ec 00 00 00 00 00 a0 00 15d+00:06:46.217 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 15d+00:06:46.205 SET FEATURES [Set transfer
mode]
Error 1333 occurred at disk power-on lifetime: 10525 hours (438 days +
13 hours)
When the command that caused the error occurred, the device was active
or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 53 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 ff ff ff 4f 00 15d+00:06:46.090 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 15d+00:06:46.081 SET FEATURES [Enable SATA
feature]
27 00 00 00 00 00 e0 00 15d+00:06:46.054 READ NATIVE MAX ADDRESS EXT
[OBS-ACS-3]
ec 00 00 00 00 00 a0 00 15d+00:06:46.051 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 15d+00:06:46.039 SET FEATURES [Set transfer
mode]
Error 1332 occurred at disk power-on lifetime: 10525 hours (438 days +
13 hours)
When the command that caused the error occurred, the device was active
or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 53 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 ff ff ff 4f 00 15d+00:06:45.922 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 15d+00:06:45.912 SET FEATURES [Enable SATA
feature]
27 00 00 00 00 00 e0 00 15d+00:06:45.886 READ NATIVE MAX ADDRESS EXT
[OBS-ACS-3]
ec 00 00 00 00 00 a0 00 15d+00:06:45.883 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 15d+00:06:45.871 SET FEATURES [Set transfer
mode]
Error 1331 occurred at disk power-on lifetime: 10525 hours (438 days +
13 hours)
When the command that caused the error occurred, the device was active
or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 53 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 ff ff ff 4f 00 15d+00:06:45.692 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 15d+00:06:45.683 SET FEATURES [Enable SATA
feature]
27 00 00 00 00 00 e0 00 15d+00:06:45.656 READ NATIVE MAX ADDRESS EXT
[OBS-ACS-3]
ec 00 00 00 00 00 a0 00 15d+00:06:45.654 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 15d+00:06:45.641 SET FEATURES [Set transfer
mode]
Error 1330 occurred at disk power-on lifetime: 10525 hours (438 days +
13 hours)
When the command that caused the error occurred, the device was active
or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 53 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 ff ff ff 4f 00 15d+00:06:45.526 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 15d+00:06:45.517 SET FEATURES [Enable SATA
feature]
27 00 00 00 00 00 e0 00 15d+00:06:45.491 READ NATIVE MAX ADDRESS EXT
[OBS-ACS-3]
ec 00 00 00 00 00 a0 00 15d+00:06:45.488 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 15d+00:06:45.475 SET FEATURES [Set transfer
mode]
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining
LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 14551 -
# 2 Extended offline Completed without error 00% 14530 -
# 3 Conveyance offline Completed without error 00% 10165 -
# 4 Conveyance offline Completed without error 00% 10165 -
# 5 Short offline Completed without error 00% 10163 -
# 6 Extended offline Completed without error 00% 9997 -
# 7 Short offline Completed without error 00% 0 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
On 10/18/21 6:52 PM, Reco wrote:
> Hi.
>
> On Mon, Oct 18, 2021 at 06:25:19PM +0200, Thomas Anderson wrote:
>> I have been having problems with a drive (non-SSD) for a while now,
>> but I would like to "identify" the problem specifically, so that I may
>> perhaps be able to get the drive replaced.
> Assuming it's SATA/IDE drive, all you need to do is:
>
> apt install smartmontools
> smartctl -t long <ur_drive_here>
> # wait for the test to finish
> smartctl -a <ur_drive_here>
>
> Please post the output of the last command.
>
> Reco
>
Reply to: