mount IDE via USB-bridge

[Bernd Kloss <b_kloss@web.de>]

Squeeze
KDE 4.4.5

Hello,

I need to import my data from my former IDE-hd and thought it might be 
easily done with an usb-bridge.
But mounting does not work.

This is my old disk:
   Device Boot      Start         End      Blocks   Id  System
/dev/sdb1   *           1       38298   307628653+  83  Linux
/dev/sdb2           38299       38913     4939987+   5  Extended
/dev/sdb5           38299       38913     4939956   82  Linux swap / Solaris

Data are on sdb2

How to mount sdb2 properly?

Thanks for helping.

Regards
Bernd




dmesg says:

[  671.140012] usb 1-5: new high speed USB device using ehci_hcd and 
address 5
[  671.273721] usb 1-5: New USB device found, idVendor=152d, 
idProduct=2338
[  671.273725] usb 1-5: New USB device strings: Mfr=1, Product=2, 
SerialNumber=5
[  671.273728] usb 1-5: Product: USB to ATA/ATAPI Bridge
[  671.273730] usb 1-5: Manufacturer: JMicron
[  671.273731] usb 1-5: SerialNumber: 152D203380B6
[  671.273822] usb 1-5: configuration #1 chosen from 1 choice
[  671.332580] Initializing USB Mass Storage driver...
[  671.332667] scsi5 : SCSI emulation for USB Mass Storage devices
[  671.332783] usbcore: registered new interface driver usb-storage
[  671.332786] USB Mass Storage support registered.
[  671.351825] usb-storage: device found at 5
[  671.351827] usb-storage: waiting for device to settle before scanning
[  676.348644] usb-storage: device scan complete
[  676.349378] scsi 5:0:0:0: Direct-Access                                    
PQ: 0 ANSI: 2 CCS
[  676.350003] sd 5:0:0:0: Attached scsi generic sg2 type 0
[  676.352182] sd 5:0:0:0: [sdb] Attached SCSI disk
[  689.004913] usb 1-5: USB disconnect, address 5
[  698.356517] usb 1-5: new high speed USB device using ehci_hcd and 
address 6
[  698.493770] usb 1-5: New USB device found, idVendor=152d, 
idProduct=2338
[  698.493773] usb 1-5: New USB device strings: Mfr=1, Product=2, 
SerialNumber=5
[  698.493776] usb 1-5: Product: USB to ATA/ATAPI Bridge
[  698.493778] usb 1-5: Manufacturer: JMicron
[  698.493779] usb 1-5: SerialNumber: 222291FACA00
[  698.493873] usb 1-5: configuration #1 chosen from 1 choice
[  698.497342] scsi6 : SCSI emulation for USB Mass Storage devices
[  698.497558] usb-storage: device found at 6
[  698.497560] usb-storage: waiting for device to settle before scanning
[  703.500197] usb-storage: device scan complete
[  703.500946] scsi 6:0:0:0: Direct-Access     ST332082 0ACE             D    
PQ: 0 ANSI: 2 CCS
[  703.501829] sd 6:0:0:0: Attached scsi generic sg2 type 0
[  703.502560] sd 6:0:0:0: [sdb] 625142448 512-byte logical blocks: (320 
GB/298 GiB)
[  703.505851] sd 6:0:0:0: [sdb] Write Protect is off
[  703.505855] sd 6:0:0:0: [sdb] Mode Sense: 00 38 00 00
[  703.505857] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[  703.507763] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[  703.507768]  sdb: sdb1 sdb2 < sdb5 >
[  703.594669] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[  703.594673] sd 6:0:0:0: [sdb] Attached SCSI disk
[  727.824071] ===>rt_ioctl_giwscan. 3(3) BSS returned, data->length = 
488
[  847.824070] ===>rt_ioctl_giwscan. 2(2) BSS returned, data->length = 
339
[  967.824570] ===>rt_ioctl_giwscan. 4(4) BSS returned, data->length = 
671
[ 1011.645301] attempt to access beyond end of device
[ 1011.645305] sdb2: rw=0, want=4, limit=2
[ 1011.645307] EXT3-fs: unable to read superblock
















Thanks
Bernd