[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Re: Card reader stopped working after update



On Mon, 27 Sep 2010 15:47:39 +1000
Veronica Brandt <veroicon@gmail.com> wrote:

> Further investigations show the sd card is not working anymore either.
> Could a power outage cause damage like that?  Leaving it on battery
> power till it goes flat?  Could that fry both the card reader and the
> card?

A dead battery ? Very doubtful.

It's almost certainly no coincidence that the card reader and card died
at the same (?) time, assuming thath you're _sure_ the SD Card itself is
dead.

A problem with voltage regulation, i.e. a hardware problem, could do
both, killing the reader and the card.  It's possible that the supply
to the reader is isolated, otherwise I would expect something else on
the laptop would also be damaged/not working.

As I said, it is possible it's on an isolated regulator and if that
regulator failed it would dave hooked up the card reader to the battery
directly killing the reader and the card.

That still seems quite unlikely, but it is possible.

Do you have a voltmeter ? 

Brian


> 
> V
> 
> On Mon, Sep 27, 2010 at 8:46 AM, Veronica Brandt <veroicon@gmail.com>
> wrote:
> 
> > Hi,
> >
> > I have an acer aspire one and use the card reader for /home/.  I
> > updated the computer Saturday (squeeze) and now booting the
> > computer the card reader is not recognised.
> >
> > I have a bug here and I don't know which package is to blame.  My
> > first thought was the kernel, but the kernel is the same.
> > Something else is fouling up the modules.  I'm running
> > 2.6.32-3-686 and tried updating to 2.6.32-5-686, but the problem is
> > still the same.
> >
> >
> > lspci:
> >
> > 04:00.0 System peripheral: JMicron Technology Corp. SD/MMC Host
> > Controller 04:00.2 SD Host controller: JMicron Technology Corp.
> > Standard SD Host Controller
> > 04:00.3 System peripheral: JMicron Technology Corp. MS Host
> > Controller 04:00.4 System peripheral: JMicron Technology Corp. xD
> > Host Controller
> >
> > lsmod | grep sd and then mmc:
> >
> > sd_mod                 25869  2
> > crc_t10dif              1012  1 sd_mod
> > scsi_mod              101401  2 sd_mod,libata
> > mmc_core               38491  0
> >
> >
> > and the error message in dmesg:
> >
> > [    3.811446] sdhci_pci: Unknown symbol sdhci_remove_host
> > [    3.937701] sdhci_pci: Unknown symbol sdhci_suspend_host
> > [    3.938338] sdhci_pci: Unknown symbol sdhci_free_host
> > [    3.938652] sdhci_pci: Unknown symbol sdhci_add_host
> > [    3.939065] sdhci_pci: Unknown symbol sdhci_resume_host
> > [    3.939440] sdhci_pci: Unknown symbol sdhci_alloc_host
> > [    3.939927] sdhci_pci: Unknown symbol sdhci_remove_host
> >
> >
> > > sudo modprobe sdhci
> > sh: Syntax error: Bad for loop variable
> > FATAL: Error running install command for sdhci
> >
> > modprobe sdricoh_cs gives no error but makes no difference
> >
> > So does anyone else have a lead I can chase up?
> >
> > Thanks
> >
> > Veronica
> >
> > --
> > brandt.id.au
> >
> 
> 
> 


Reply to: