Slow booting
After init of soundcard and before swap activation i have 90 seconds
hole. Is it normal? Can I configure kernel to somewhat avoid this?
I use mainly debian testing, 64bit version.
--
Pozdrawiam
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.30-2-amd64 (Debian 2.6.30-8) (waldi@debian.org) (gcc version 4.3.4 (Debian 4.3.4-3) ) #1 SMP Fri Sep 25 22:16:56 UTC 2009
[ 0.000000] Command line: root=/dev/sda2 ro notsc vga=0
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] Centaur CentaurHauls
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007fe90000 (usable)
[ 0.000000] BIOS-e820: 000000007fe90000 - 000000007fe9b000 (ACPI data)
[ 0.000000] BIOS-e820: 000000007fe9b000 - 000000007ff00000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000007ff00000 - 0000000080000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
[ 0.000000] BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
[ 0.000000] DMI present.
[ 0.000000] last_pfn = 0x7fe90 max_arch_pfn = 0x100000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-CFFFF write-protect
[ 0.000000] D0000-DFFFF uncachable
[ 0.000000] E0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask F80000000 write-back
[ 0.000000] 1 base 07FF00000 mask FFFF00000 uncachable
[ 0.000000] 2 disabled
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] init_memory_mapping: 0000000000000000-000000007fe90000
[ 0.000000] 0000000000 - 007fe00000 page 2M
[ 0.000000] 007fe00000 - 007fe90000 page 4k
[ 0.000000] kernel direct mapping tables up to 7fe90000 @ 8000-c000
[ 0.000000] RAMDISK: 376f9000 - 37fef431
[ 0.000000] ACPI: RSDP 00000000000f77b0 00014 (v00 FSC )
[ 0.000000] ACPI: RSDT 000000007fe94eff 00044 (v01 PTLTD PC 06040000 LTP 00000000)
[ 0.000000] ACPI: FACP 000000007fe9ae20 00074 (v01 INTEL CALISTGA 06040000 LOHR 0000005A)
[ 0.000000] ACPI: DSDT 000000007fe95ade 05342 (v01 UW____ F29_____ 06040000 INTL 20050624)
[ 0.000000] ACPI: FACS 000000007fe9bfc0 00040
[ 0.000000] ACPI: APIC 000000007fe9ae94 00068 (v01 INTEL CALISTGA 06040000 LOHR 0000005A)
[ 0.000000] ACPI: HPET 000000007fe9aefc 00038 (v01 INTEL CALISTGA 06040000 LOHR 0000005A)
[ 0.000000] ACPI: MCFG 000000007fe9af34 0003C (v01 INTEL CALISTGA 06040000 LOHR 0000005A)
[ 0.000000] ACPI: APIC 000000007fe9af70 00068 (v01 FSC PC 06040000 LTP 00000000)
[ 0.000000] ACPI: BOOT 000000007fe9afd8 00028 (v01 FSC PC 06040000 LTP 00000001)
[ 0.000000] ACPI: SSDT 000000007fe958d4 0020A (v01 SataRe SataAhci 00001000 INTL 20050624)
[ 0.000000] ACPI: SSDT 000000007fe94f43 004F6 (v01 PmRef CpuPm 00003000 INTL 20050624)
[ 0.000000] ACPI: BIOS bug: multiple APIC/MADT found, using 0
[ 0.000000] ACPI: If "acpi_apic_instance=2" works better, notify linux-acpi@vger.kernel.org
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at 0000000000000000-000000007fe90000
[ 0.000000] Bootmem setup node 0 0000000000000000-000000007fe90000
[ 0.000000] NODE_DATA [000000000000a000 - 0000000000011fff]
[ 0.000000] bootmap [0000000000012000 - 0000000000021fd7] pages 10
[ 0.000000] (7 early reservations) ==> bootmem [0000000000 - 007fe90000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
[ 0.000000] #1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
[ 0.000000] #2 [0000200000 - 00007ddb0c] TEXT DATA BSS ==> [0000200000 - 00007ddb0c]
[ 0.000000] #3 [00376f9000 - 0037fef431] RAMDISK ==> [00376f9000 - 0037fef431]
[ 0.000000] #4 [000009f800 - 0000100000] BIOS reserved ==> [000009f800 - 0000100000]
[ 0.000000] #5 [00007de000 - 00007de194] BRK ==> [00007de000 - 00007de194]
[ 0.000000] #6 [0000008000 - 000000a000] PGTABLE ==> [0000008000 - 000000a000]
[ 0.000000] found SMP MP-table at [ffff8800000f7860] f7860
[ 0.000000] [ffffe20000000000-ffffe20001bfffff] PMD -> [ffff880001200000-ffff880002dfffff] on node 0
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000000 -> 0x00001000
[ 0.000000] DMA32 0x00001000 -> 0x00100000
[ 0.000000] Normal 0x00100000 -> 0x00100000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x0007fe90
[ 0.000000] On node 0 totalpages: 523823
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 1602 pages reserved
[ 0.000000] DMA zone: 2341 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 7107 pages used for memmap
[ 0.000000] DMA32 zone: 512717 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 0, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 24
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e4000
[ 0.000000] PM: Registered nosave memory: 00000000000e4000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 88000000 (gap: 80000000:60000000)
[ 0.000000] NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:2 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 26 pages at ffff880001010000, static data 76256 bytes
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 515058
[ 0.000000] Policy zone: DMA32
[ 0.000000] Kernel command line: root=/dev/sda2 ro notsc vga=0
[ 0.000000] notsc: Kernel compiled with CONFIG_X86_TSC, cannot disable TSC completely.
[ 0.000000] Initializing CPU#0
[ 0.000000] Experimental hierarchical RCU implementation.
[ 0.000000] Experimental hierarchical RCU init done.
[ 0.000000] NR_IRQS:4352 nr_irqs:424
[ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 1662.774 MHz processor.
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 2051032k/2095680k available (2784k kernel code, 388k absent, 44260k reserved, 1411k data, 560k init)
[ 0.000000] hpet clockevent registered
[ 0.000000] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[ 0.000000] Calibrating delay loop... 3309.56 BogoMIPS (lpj=6619136)
[ 0.100000] Security Framework initialized
[ 0.100000] SELinux: Disabled at boot.
[ 0.100000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.100000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.100000] Mount-cache hash table entries: 256
[ 0.100000] Initializing cgroup subsys ns
[ 0.100000] Initializing cgroup subsys cpuacct
[ 0.100000] Initializing cgroup subsys devices
[ 0.100000] Initializing cgroup subsys freezer
[ 0.100000] Initializing cgroup subsys net_cls
[ 0.100000] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.100000] CPU: L2 cache: 2048K
[ 0.100000] CPU 0/0x0 -> Node 0
[ 0.100000] CPU: Physical Processor ID: 0
[ 0.100000] CPU: Processor Core ID: 0
[ 0.104000] CPU0: Thermal monitoring enabled (TM2)
[ 0.104000] using mwait in idle threads.
[ 0.104000] ACPI: Core revision 20090320
[ 0.116000] Setting APIC routing to flat
[ 0.116000] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.156001] CPU0: Intel(R) Core(TM)2 CPU T5500 @ 1.66GHz stepping 06
[ 0.156001] Booting processor 1 APIC 0x1 ip 0x6000
[ 0.004000] Initializing CPU#1
[ 0.004000] Calibrating delay loop... 3317.76 BogoMIPS (lpj=6635520)
[ 0.004000] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.004000] CPU: L2 cache: 2048K
[ 0.004000] CPU 1/0x1 -> Node 0
[ 0.004000] CPU: Physical Processor ID: 0
[ 0.004000] CPU: Processor Core ID: 1
[ 0.004000] CPU1: Thermal monitoring enabled (TM2)
[ 0.004000] x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
[ 0.264001] CPU1: Intel(R) Core(TM)2 CPU T5500 @ 1.66GHz stepping 06
[ 0.264001] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 0.268001] Brought up 2 CPUs
[ 0.268001] Total of 2 processors activated (6627.32 BogoMIPS).
[ 0.268001] CPU0 attaching sched-domain:
[ 0.268001] domain 0: span 0-1 level MC
[ 0.268001] groups: 0 1
[ 0.268001] CPU1 attaching sched-domain:
[ 0.268001] domain 0: span 0-1 level MC
[ 0.268001] groups: 1 0
[ 0.268001] net_namespace: 1936 bytes
[ 0.268001] Booting paravirtualized kernel on bare hardware
[ 0.268001] regulator: core version 0.5
[ 0.268001] NET: Registered protocol family 16
[ 0.272001] ACPI: bus type pci registered
[ 0.272001] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[ 0.272001] PCI: MCFG area at e0000000 reserved in E820
[ 0.280001] PCI: Using MMCONFIG at e0000000 - efffffff
[ 0.280001] PCI: Using configuration type 1 for base access
[ 0.280001] bio: create slab <bio-0> at 0
[ 0.284001] ACPI: EC: Look up EC in DSDT
[ 0.284001] ACPI: BIOS _OSI(Linux) query ignored
[ 0.288001] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 18.292027] ACPI: Interpreter enabled
[ 18.292027] ACPI: (supports S0 S3 S4 S5)
[ 18.292027] ACPI: Using IOAPIC for interrupt routing
[ 18.296027] ACPI: EC: GPE = 0x19, I/O: command/status = 0x66, data = 0x62
[ 18.296027] ACPI: EC: driver started in interrupt mode
[ 18.300027] ACPI: No dock devices found.
[ 18.300027] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 18.300027] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 18.300027] pci 0000:00:01.0: PME# disabled
[ 18.300027] pci 0000:00:1b.0: reg 10 64bit mmio: [0xb0000000-0xb0003fff]
[ 18.300027] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 18.300027] pci 0000:00:1b.0: PME# disabled
[ 18.300027] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 18.300027] pci 0000:00:1c.0: PME# disabled
[ 18.300027] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[ 18.300027] pci 0000:00:1c.2: PME# disabled
[ 18.300027] pci 0000:00:1d.0: reg 20 io port: [0x1800-0x181f]
[ 18.300027] pci 0000:00:1d.1: reg 20 io port: [0x1820-0x183f]
[ 18.300027] pci 0000:00:1d.2: reg 20 io port: [0x1840-0x185f]
[ 18.300027] pci 0000:00:1d.3: reg 20 io port: [0x1860-0x187f]
[ 18.300027] pci 0000:00:1d.7: reg 10 32bit mmio: [0xb0004000-0xb00043ff]
[ 18.300027] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 18.300027] pci 0000:00:1d.7: PME# disabled
[ 18.300027] pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
[ 18.304027] pci 0000:00:1f.0: quirk: region 1180-11bf claimed by ICH6 GPIO
[ 18.304027] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0068 (mask 0007)
[ 18.304027] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 0200 (mask 000f)
[ 18.304027] pci 0000:00:1f.1: reg 10 io port: [0x00-0x07]
[ 18.304027] pci 0000:00:1f.1: reg 14 io port: [0x00-0x03]
[ 18.304027] pci 0000:00:1f.1: reg 18 io port: [0x00-0x07]
[ 18.304027] pci 0000:00:1f.1: reg 1c io port: [0x00-0x03]
[ 18.304027] pci 0000:00:1f.1: reg 20 io port: [0x1880-0x188f]
[ 18.304027] pci 0000:00:1f.2: reg 10 io port: [0x18c8-0x18cf]
[ 18.304027] pci 0000:00:1f.2: reg 14 io port: [0x18ac-0x18af]
[ 18.304027] pci 0000:00:1f.2: reg 18 io port: [0x18c0-0x18c7]
[ 18.304027] pci 0000:00:1f.2: reg 1c io port: [0x18a8-0x18ab]
[ 18.304027] pci 0000:00:1f.2: reg 20 io port: [0x18b0-0x18bf]
[ 18.304027] pci 0000:00:1f.2: reg 24 32bit mmio: [0xb0004400-0xb00047ff]
[ 18.304027] pci 0000:00:1f.2: PME# supported from D3hot
[ 18.304027] pci 0000:00:1f.2: PME# disabled
[ 18.304027] pci 0000:00:1f.3: reg 20 io port: [0x18e0-0x18ff]
[ 18.304027] pci 0000:01:00.0: reg 10 32bit mmio: [0xc0000000-0xcfffffff]
[ 18.304027] pci 0000:01:00.0: reg 14 io port: [0x2000-0x20ff]
[ 18.304027] pci 0000:01:00.0: reg 18 32bit mmio: [0xb0100000-0xb010ffff]
[ 18.304027] pci 0000:01:00.0: reg 30 32bit mmio: [0x000000-0x01ffff]
[ 18.304027] pci 0000:01:00.0: supports D1 D2
[ 18.304027] pci 0000:00:01.0: bridge io port: [0x2000-0x2fff]
[ 18.304027] pci 0000:00:01.0: bridge 32bit mmio: [0xb0100000-0xb01fffff]
[ 18.304027] pci 0000:00:01.0: bridge 64bit mmio pref: [0xc0000000-0xcfffffff]
[ 18.304027] pci 0000:00:1c.0: bridge io port: [0x00-0xffff]
[ 18.304027] pci 0000:00:1c.0: bridge 32bit mmio: [0xfac00000-0xfebfffff]
[ 18.304027] pci 0000:04:00.0: reg 10 32bit mmio: [0xb0200000-0xb0200fff]
[ 18.304027] pci 0000:04:00.0: PME# supported from D0 D3hot D3cold
[ 18.304027] pci 0000:04:00.0: PME# disabled
[ 18.304027] pci 0000:00:1c.2: bridge 32bit mmio: [0xb0200000-0xb02fffff]
[ 18.304027] pci 0000:05:04.0: reg 10 32bit mmio: [0xb0304000-0xb03047ff]
[ 18.304027] pci 0000:05:04.0: reg 14 32bit mmio: [0xb0300000-0xb0303fff]
[ 18.304027] pci 0000:05:04.0: supports D1 D2
[ 18.304027] pci 0000:05:04.0: PME# supported from D0 D1 D2 D3hot
[ 18.304027] pci 0000:05:04.0: PME# disabled
[ 18.304027] pci 0000:05:05.0: reg 10 io port: [0x3000-0x30ff]
[ 18.304027] pci 0000:05:05.0: reg 14 32bit mmio: [0xb0304800-0xb03048ff]
[ 18.304027] pci 0000:05:05.0: reg 30 32bit mmio: [0x000000-0x01ffff]
[ 18.304027] pci 0000:05:05.0: supports D1 D2
[ 18.304027] pci 0000:05:05.0: PME# supported from D1 D2 D3hot D3cold
[ 18.304027] pci 0000:05:05.0: PME# disabled
[ 18.304027] pci 0000:00:1e.0: transparent bridge
[ 18.304027] pci 0000:00:1e.0: bridge io port: [0x3000-0x3fff]
[ 18.304027] pci 0000:00:1e.0: bridge 32bit mmio: [0xb0300000-0xb03fffff]
[ 18.304027] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 18.304027] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGP._PRT]
[ 18.304027] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[ 18.304027] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT]
[ 18.304027] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
[ 18.308027] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[ 18.312027] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
[ 18.312027] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 *3 4 5 6 7 10 12 14 15)
[ 18.312027] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
[ 18.312027] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
[ 18.312027] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
[ 18.316027] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 *7 10 12 14 15)
[ 18.316027] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 *5 6 7 11 12 14 15)
[ 18.316027] usbcore: registered new interface driver usbfs
[ 18.316027] usbcore: registered new interface driver hub
[ 18.316027] usbcore: registered new device driver usb
[ 18.316027] PCI: Using ACPI for IRQ routing
[ 18.316027] pci 0000:00:1c.0: BAR 13: can't allocate resource
[ 18.324027] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 18.324027] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[ 18.332029] Switched to high resolution mode on CPU 0
[ 18.334380] Switched to high resolution mode on CPU 1
[ 18.344002] pnp: PnP ACPI init
[ 18.344002] ACPI: bus type pnp registered
[ 18.344002] pnp: PnP ACPI: found 11 devices
[ 18.344002] ACPI: ACPI bus type pnp unregistered
[ 18.344002] system 00:01: iomem range 0xe0000000-0xefffffff has been reserved
[ 18.344002] system 00:01: iomem range 0xfed14000-0xfed17fff has been reserved
[ 18.344002] system 00:01: iomem range 0xfed18000-0xfed18fff has been reserved
[ 18.344002] system 00:01: iomem range 0xfed19000-0xfed19fff has been reserved
[ 18.344002] system 00:01: iomem range 0xfed1c000-0xfed1ffff has been reserved
[ 18.344002] system 00:01: iomem range 0xfed20000-0xfed3ffff has been reserved
[ 18.344002] system 00:01: iomem range 0xfed40000-0xfed44fff has been reserved
[ 18.344002] system 00:01: iomem range 0xfed45000-0xfed8ffff has been reserved
[ 18.344002] system 00:04: iomem range 0xfed00000-0xfed003ff has been reserved
[ 18.344002] system 00:06: ioport range 0x680-0x69f has been reserved
[ 18.344002] system 00:06: ioport range 0x800-0x80f has been reserved
[ 18.344002] system 00:06: ioport range 0x1000-0x107f has been reserved
[ 18.347083] system 00:06: ioport range 0x1180-0x11bf has been reserved
[ 18.347083] system 00:06: ioport range 0x1640-0x164f has been reserved
[ 18.347083] system 00:07: ioport range 0x6a0-0x6af has been reserved
[ 18.347083] system 00:07: ioport range 0x6b0-0x6ff has been reserved
[ 18.348897] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[ 18.348897] pci 0000:00:01.0: IO window: 0x2000-0x2fff
[ 18.348897] pci 0000:00:01.0: MEM window: 0xb0100000-0xb01fffff
[ 18.348897] pci 0000:00:01.0: PREFETCH window: 0x000000c0000000-0x000000cfffffff
[ 18.348897] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
[ 18.348897] pci 0000:00:1c.0: IO window: disabled
[ 18.348897] pci 0000:00:1c.0: MEM window: 0xfac00000-0xfebfffff
[ 18.348897] pci 0000:00:1c.0: PREFETCH window: disabled
[ 18.348897] pci 0000:00:1c.2: PCI bridge, secondary bus 0000:04
[ 18.348897] pci 0000:00:1c.2: IO window: disabled
[ 18.348897] pci 0000:00:1c.2: MEM window: 0xb0200000-0xb02fffff
[ 18.348897] pci 0000:00:1c.2: PREFETCH window: disabled
[ 18.348897] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:05
[ 18.348897] pci 0000:00:1e.0: IO window: 0x3000-0x3fff
[ 18.348897] pci 0000:00:1e.0: MEM window: 0xb0300000-0xb03fffff
[ 18.348897] pci 0000:00:1e.0: PREFETCH window: 0x00000088000000-0x000000880fffff
[ 18.348897] alloc irq_desc for 16 on cpu 0 node 0
[ 18.348897] alloc kstat_irqs on cpu 0 node 0
[ 18.348897] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 18.348897] pci 0000:00:01.0: setting latency timer to 64
[ 18.348897] pci 0000:00:1c.0: enabling device (0000 -> 0002)
[ 18.348897] alloc irq_desc for 17 on cpu 0 node 0
[ 18.348897] alloc kstat_irqs on cpu 0 node 0
[ 18.348897] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 18.348897] pci 0000:00:1c.0: setting latency timer to 64
[ 18.348897] pci 0000:00:1c.2: enabling device (0000 -> 0002)
[ 18.348897] alloc irq_desc for 18 on cpu 0 node 0
[ 18.348897] alloc kstat_irqs on cpu 0 node 0
[ 18.348897] pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 18.348897] pci 0000:00:1c.2: setting latency timer to 64
[ 18.348897] pci 0000:00:1e.0: setting latency timer to 64
[ 18.348897] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 18.348897] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
[ 18.348897] pci_bus 0000:01: resource 0 io: [0x2000-0x2fff]
[ 18.348897] pci_bus 0000:01: resource 1 mem: [0xb0100000-0xb01fffff]
[ 18.348897] pci_bus 0000:01: resource 2 pref mem [0xc0000000-0xcfffffff]
[ 18.348897] pci_bus 0000:02: resource 0 mem: [0x0-0xffff]
[ 18.348897] pci_bus 0000:02: resource 1 mem: [0xfac00000-0xfebfffff]
[ 18.348897] pci_bus 0000:04: resource 1 mem: [0xb0200000-0xb02fffff]
[ 18.348897] pci_bus 0000:05: resource 0 io: [0x3000-0x3fff]
[ 18.348897] pci_bus 0000:05: resource 1 mem: [0xb0300000-0xb03fffff]
[ 18.348897] pci_bus 0000:05: resource 2 pref mem [0x88000000-0x880fffff]
[ 18.348897] pci_bus 0000:05: resource 3 io: [0x00-0xffff]
[ 18.348897] pci_bus 0000:05: resource 4 mem: [0x000000-0xffffffffffffffff]
[ 18.348897] NET: Registered protocol family 2
[ 18.388002] IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 18.388002] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
[ 18.388022] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 18.388022] TCP: Hash tables configured (established 262144 bind 65536)
[ 18.388022] TCP reno registered
[ 18.404002] NET: Registered protocol family 1
[ 18.404002] Trying to unpack rootfs image as initramfs...
[ 18.668006] Freeing initrd memory: 9177k freed
[ 18.675301] Simple Boot Flag at 0x35 set to 0x1
[ 18.680003] audit: initializing netlink socket (disabled)
[ 18.680003] type=2000 audit(1257437336.676:1): initialized
[ 18.680003] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 18.680003] VFS: Disk quotas dquot_6.5.2
[ 18.680003] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 18.680003] msgmni has been set to 4023
[ 18.680003] alg: No test for stdrng (krng)
[ 18.680003] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 18.680003] io scheduler noop registered
[ 18.680003] io scheduler anticipatory registered
[ 18.680003] io scheduler deadline registered
[ 18.680003] io scheduler cfq registered (default)
[ 18.680003] pci 0000:01:00.0: Boot video device
[ 18.680003] alloc irq_desc for 24 on cpu 0 node 0
[ 18.680003] alloc kstat_irqs on cpu 0 node 0
[ 18.680003] pcieport-driver 0000:00:01.0: irq 24 for MSI/MSI-X
[ 18.680003] pcieport-driver 0000:00:01.0: setting latency timer to 64
[ 18.680003] alloc irq_desc for 25 on cpu 0 node 0
[ 18.680003] alloc kstat_irqs on cpu 0 node 0
[ 18.680003] pcieport-driver 0000:00:1c.0: irq 25 for MSI/MSI-X
[ 18.680003] pcieport-driver 0000:00:1c.0: setting latency timer to 64
[ 18.680003] alloc irq_desc for 26 on cpu 0 node 0
[ 18.680003] alloc kstat_irqs on cpu 0 node 0
[ 18.680003] pcieport-driver 0000:00:1c.2: irq 26 for MSI/MSI-X
[ 18.680003] pcieport-driver 0000:00:1c.2: setting latency timer to 64
[ 18.687970] Linux agpgart interface v0.103
[ 18.687970] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 18.687970] brd: module loaded
[ 18.687970] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[ 18.687970] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 18.691875] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 18.691875] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 18.691875] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 18.691875] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 18.691875] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 18.691875] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 18.691875] mice: PS/2 mouse device common for all mice
[ 18.691875] rtc_cmos 00:08: rtc core: registered rtc_cmos as rtc0
[ 18.691875] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[ 18.691875] cpuidle: using governor ladder
[ 18.691875] cpuidle: using governor menu
[ 18.691875] No iBFT detected.
[ 18.695761] TCP cubic registered
[ 18.695761] NET: Registered protocol family 10
[ 18.695761] lo: Disabled Privacy Extensions
[ 18.695761] Mobile IPv6
[ 18.695761] NET: Registered protocol family 17
[ 18.695761] registered taskstats version 1
[ 18.695761] rtc_cmos 00:08: setting system clock to 2009-11-05 16:08:57 UTC (1257437337)
[ 18.695761] Freeing unused kernel memory: 560k freed
[ 18.695761] Write protecting the kernel read-only data: 3808k
[ 18.772845] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[ 18.906683] thermal LNXTHERM:01: registered as thermal_zone0
[ 18.906683] ACPI: Thermal Zone [THRM] (29 C)
[ 18.965005] SCSI subsystem initialized
[ 18.976004] Uniform Multi-Platform E-IDE driver
[ 18.976004] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 18.976008] alloc irq_desc for 23 on cpu 0 node 0
[ 18.976008] alloc kstat_irqs on cpu 0 node 0
[ 18.976008] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 18.976008] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 18.976008] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 18.976008] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[ 18.980008] ehci_hcd 0000:00:1d.7: debug port 1
[ 18.980008] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 18.980008] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xb0004000
[ 18.996009] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 18.996009] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 18.996009] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 18.996009] usb usb1: Product: EHCI Host Controller
[ 18.996009] usb usb1: Manufacturer: Linux 2.6.30-2-amd64 ehci_hcd
[ 18.996009] usb usb1: SerialNumber: 0000:00:1d.7
[ 18.996009] usb usb1: configuration #1 chosen from 1 choice
[ 18.996009] hub 1-0:1.0: USB hub found
[ 18.996009] hub 1-0:1.0: 8 ports detected
[ 19.024010] uhci_hcd: USB Universal Host Controller Interface driver
[ 19.024010] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 19.024010] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 19.024010] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 19.024010] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 19.024022] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001800
[ 19.024022] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 19.024022] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 19.024022] usb usb2: Product: UHCI Host Controller
[ 19.024022] usb usb2: Manufacturer: Linux 2.6.30-2-amd64 uhci_hcd
[ 19.024022] usb usb2: SerialNumber: 0000:00:1d.0
[ 19.024022] usb usb2: configuration #1 chosen from 1 choice
[ 19.024022] hub 2-0:1.0: USB hub found
[ 19.024022] hub 2-0:1.0: 2 ports detected
[ 19.108008] alloc irq_desc for 19 on cpu 0 node 0
[ 19.108008] alloc kstat_irqs on cpu 0 node 0
[ 19.108008] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 19.108008] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 19.108008] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 19.108008] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 19.108008] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001820
[ 19.108008] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 19.108008] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 19.108008] usb usb3: Product: UHCI Host Controller
[ 19.108618] usb usb3: Manufacturer: Linux 2.6.30-2-amd64 uhci_hcd
[ 19.108618] usb usb3: SerialNumber: 0000:00:1d.1
[ 19.108618] usb usb3: configuration #1 chosen from 1 choice
[ 19.108618] hub 3-0:1.0: USB hub found
[ 19.112618] hub 3-0:1.0: 2 ports detected
[ 19.112618] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 19.112618] r8169 0000:05:05.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 19.112618] r8169 0000:05:05.0: no PCI Express capability
[ 19.112618] eth0: RTL8169sb/8110sb at 0xffffc20010a34800, 00:03:0d:4e:ff:80, XID 10000000 IRQ 19
[ 19.124012] piix 0000:00:1f.1: IDE controller (0x8086:0x27df rev 0x02)
[ 19.124012] libata version 3.00 loaded.
[ 19.124012] PIIX_IDE 0000:00:1f.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 19.124012] piix 0000:00:1f.1: IDE port disabled
[ 19.124012] piix 0000:00:1f.1: not 100% native mode: will probe irqs later
[ 19.124012] ide0: BM-DMA at 0x1880-0x1887
[ 19.124012] Probing IDE interface ide0...
[ 19.136004] acpi device:04: registered as cooling_device0
[ 19.136004] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:01/device:02/input/input2
[ 19.136004] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 19.140010] firewire_ohci 0000:05:04.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 19.188014] udev: renamed network interface eth0 to eth3
[ 19.212006] firewire_ohci: Added fw-ohci device 0000:05:04.0, OHCI version 1.10
[ 19.712002] firewire_core: created device fw0: GUID 00030d4953024347, S400
[ 19.860002] hda: Optiarc DVD RW AD-7540A, ATAPI CD/DVD-ROM drive
[ 20.532002] hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
[ 20.532002] hda: UDMA/33 mode selected
[ 20.533012] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 20.540002] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 20.540002] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 20.540002] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 20.540002] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 20.540002] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001840
[ 20.540002] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 20.540002] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 20.540002] usb usb4: Product: UHCI Host Controller
[ 20.540002] usb usb4: Manufacturer: Linux 2.6.30-2-amd64 uhci_hcd
[ 20.540002] usb usb4: SerialNumber: 0000:00:1d.2
[ 20.543263] usb usb4: configuration #1 chosen from 1 choice
[ 20.543263] hub 4-0:1.0: USB hub found
[ 20.543263] hub 4-0:1.0: 2 ports detected
[ 20.543263] ahci 0000:00:1f.2: version 3.0
[ 20.543263] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 20.543263] alloc irq_desc for 27 on cpu 0 node 0
[ 20.543263] alloc kstat_irqs on cpu 0 node 0
[ 20.543263] ahci 0000:00:1f.2: irq 27 for MSI/MSI-X
[ 20.543263] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 1.5 Gbps 0x5 impl SATA mode
[ 20.543263] ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part
[ 20.543263] ahci 0000:00:1f.2: setting latency timer to 64
[ 20.543263] scsi0 : ahci
[ 20.543263] scsi1 : ahci
[ 20.543263] scsi2 : ahci
[ 20.543263] scsi3 : ahci
[ 20.543263] ata1: SATA max UDMA/133 abar m1024@0xb0004400 port 0xb0004500 irq 27
[ 20.543263] ata2: DUMMY
[ 20.543263] ata3: SATA max UDMA/133 abar m1024@0xb0004400 port 0xb0004600 irq 27
[ 20.543263] ata4: DUMMY
[ 20.543263] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
[ 20.543263] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[ 20.543263] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 20.543263] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[ 20.543263] uhci_hcd 0000:00:1d.3: irq 16, io base 0x00001860
[ 20.543263] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 20.543263] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 20.543263] usb usb5: Product: UHCI Host Controller
[ 20.543263] usb usb5: Manufacturer: Linux 2.6.30-2-amd64 uhci_hcd
[ 20.543263] usb usb5: SerialNumber: 0000:00:1d.3
[ 20.543263] usb usb5: configuration #1 chosen from 1 choice
[ 20.543263] hub 5-0:1.0: USB hub found
[ 20.543263] hub 5-0:1.0: 2 ports detected
[ 20.861005] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 20.861005] ata3: SATA link down (SStatus 0 SControl 300)
[ 20.864002] ata1.00: ACPI cmd ef/90:03:00:00:00:a0 rejected by device (Stat=0x51 Err=0x04)
[ 21.229277] ata1.00: ATA-7: WDC WD1200BEVS-07LAT0, 01.06M01, max UDMA/133
[ 21.229277] ata1.00: 234441648 sectors, multi 16: LBA48 NCQ (depth 1)
[ 21.229277] ata1.00: ACPI cmd ef/90:03:00:00:00:a0 rejected by device (Stat=0x51 Err=0x04)
[ 21.229277] ata1.00: configured for UDMA/133
[ 21.244002] scsi 0:0:0:0: Direct-Access ATA WDC WD1200BEVS-0 01.0 PQ: 0 ANSI: 5
[ 21.252010] ide-cd driver 5.00
[ 21.252770] ide-cd: hda: ATAPI 24X DVD-ROM DVD-R/RAM CD-R/RW drive, 2048kB Cache
[ 21.256770] Uniform CD-ROM driver Revision: 3.20
[ 21.260125] Driver 'sd' needs updating - please use bus_type methods
[ 21.260125] sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors: (120 GB/111 GiB)
[ 21.260125] sd 0:0:0:0: [sda] Write Protect is off
[ 21.260125] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 21.260125] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 21.260125] sda: sda1 sda2 sda3
[ 21.296460] sd 0:0:0:0: [sda] Attached SCSI disk
[ 21.800003] PM: Starting manual resume from disk
[ 21.856001] kjournald starting. Commit interval 5 seconds
[ 21.856001] EXT3-fs: mounted filesystem with ordered data mode.
[ 25.098050] udev: starting version 141
[ 26.123567] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 26.123567] ACPI: Power Button [PWRF]
[ 26.123567] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input4
[ 26.123567] ACPI: Lid Switch [LID0]
[ 26.123567] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input5
[ 26.123567] ACPI: Power Button [PWRB]
[ 26.123567] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input6
[ 26.123567] ACPI: Sleep Button [SLPB]
[ 26.160005] ACPI: SSDT 000000007fe95689 001C2 (v01 PmRef Cpu0Ist 00003000 INTL 20050624)
[ 26.160005] ACPI: SSDT 000000007fe95439 001CB (v01 PmRef Cpu0Cst 00003001 INTL 20050624)
[ 26.160005] Marking TSC unstable due to TSC halts in idle
[ 26.160410] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[ 26.160410] processor ACPI_CPU:00: registered as cooling_device1
[ 26.160410] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 26.160410] ACPI: SSDT 000000007fe9584b 00089 (v01 PmRef Cpu1Ist 00003000 INTL 20050624)
[ 26.160410] ACPI: SSDT 000000007fe95604 00085 (v01 PmRef Cpu1Cst 00003000 INTL 20050624)
[ 26.160410] ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
[ 26.160410] processor ACPI_CPU:01: registered as cooling_device2
[ 26.160410] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 26.432890] ACPI: WMI: Mapper loaded
[ 26.468024] ACPI: AC Adapter [AC0] (on-line)
[ 26.495977] ACPI: Battery Slot [BAT0] (battery present)
[ 26.644821] intel_rng: FWH not detected
[ 26.929494] input: PC Speaker as /devices/platform/pcspkr/input/input7
[ 27.288008] cfg80211: Using static regulatory domain info
[ 27.288509] cfg80211: Regulatory domain: US
[ 27.288509] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 27.288509] (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
[ 27.288509] (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 27.288509] (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 27.288509] (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 27.288509] (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 27.288509] (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
[ 27.288509] cfg80211: Calling CRDA for country: US
[ 27.808021] Synaptics Touchpad, model: 1, fw: 6.2, id: 0xa0b1, caps: 0xa04713/0x20040a
[ 27.827880] i801_smbus 0000:00:1f.3: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 27.840144] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input8
[ 28.137022] iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network Connection driver for Linux, 1.2.26ks
[ 28.137022] iwl3945: Copyright(c) 2003-2009 Intel Corporation
[ 28.144017] iwl3945 0000:04:00.0: enabling device (0000 -> 0002)
[ 28.144017] iwl3945 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 28.144017] iwl3945 0000:04:00.0: setting latency timer to 64
[ 28.197029] iwl3945 0000:04:00.0: Tunable channels: 13 802.11bg, 23 802.11a channels
[ 28.197029] iwl3945 0000:04:00.0: Detected Intel Wireless WiFi Link 3945ABG
[ 28.197029] alloc irq_desc for 28 on cpu 0 node 0
[ 28.197029] alloc kstat_irqs on cpu 0 node 0
[ 28.197029] iwl3945 0000:04:00.0: irq 28 for MSI/MSI-X
[ 28.495478] phy0: Selected rate control algorithm 'iwl-3945-rs'
[ 28.497053] udev: renamed network interface wmaster0 to eth2
[ 28.547421] alloc irq_desc for 22 on cpu 0 node 0
[ 28.547421] alloc kstat_irqs on cpu 0 node 0
[ 28.547421] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 28.547421] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 28.694565] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input9
[ 119.378304] Adding 6000268k swap on /dev/sda3. Priority:-1 extents:1 across:6000268k
[ 119.736022] EXT3 FS on sda2, internal journal
[ 120.043968] loop: module loaded
[ 120.286598] device-mapper: uevent: version 1.0.3
[ 120.287596] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
[ 123.866746] r8169: eth3: link up
[ 134.240023] eth3: no IPv6 routers present
[ 137.716022] iwl3945 0000:04:00.0: firmware: requesting iwlwifi-3945-2.ucode
[ 137.786305] iwl3945 0000:04:00.0: loaded firmware version 15.32.2.9
[ 137.831956] Registered led device: iwl-phy0::radio
[ 137.831956] Registered led device: iwl-phy0::assoc
[ 137.831956] Registered led device: iwl-phy0::RX
[ 137.831956] Registered led device: iwl-phy0::TX
[ 137.848738] ADDRCONF(NETDEV_UP): wlan0_rename: link is not ready
[ 147.356023] lp: driver loaded but no devices found
[ 147.465400] ppdev: user-space parallel port driver
[ 150.592023] pci 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 150.785026] [drm] Initialized drm 1.1.0 20060810
[ 150.923409] pci 0000:01:00.0: setting latency timer to 64
[ 150.924013] [drm] Initialized radeon 1.30.0 20080528 for 0000:01:00.0 on minor 0
[ 151.892634] [drm] Setting GART location based on new memory map
[ 151.892634] [drm] Loading R500 Microcode
[ 151.892634] platform radeon_cp.0: firmware: requesting radeon/R520_cp.bin
[ 151.927854] [drm] Num pipes: 1
[ 151.927854] [drm] writeback test succeeded in 1 usecs
[ 154.348026] ata1.00: configured for UDMA/133
[ 154.348026] ata1: EH complete
[ 173.517048] [drm] Num pipes: 1
[ 455.223744] CE: hpet increasing min_delta_ns to 15000 nsec
[ 822.577801] CE: hpet increasing min_delta_ns to 22500 nsec
[ 1308.444867] [drm] Num pipes: 1
[ 1312.772019] [drm] Num pipes: 1
[ 1480.228020] ata1.00: configured for UDMA/133
[ 1480.228020] ata1: EH complete
[ 1749.117696] udev: starting version 146
[ 2998.695118] [drm] Num pipes: 1
[ 4535.595258] psmouse.c: TouchPad at isa0060/serio4/input0 lost sync at byte 1
[ 4535.596022] psmouse.c: TouchPad at isa0060/serio4/input0 lost sync at byte 1
[ 4535.596022] psmouse.c: TouchPad at isa0060/serio4/input0 lost sync at byte 1
[ 4535.596022] psmouse.c: TouchPad at isa0060/serio4/input0 lost sync at byte 1
[ 4535.600044] psmouse.c: TouchPad at isa0060/serio4/input0 lost sync at byte 1
[ 4535.600044] psmouse.c: issuing reconnect request
# menu.lst - See: grub(8), info grub, update-grub(8)
# grub-install(8), grub-floppy(8),
# grub-md5-crypt, /usr/share/doc/grub
# and /usr/share/doc/grub-doc/.
## default num
# Set the default entry to the entry number NUM. Numbering starts from 0, and
# the entry number 0 is the default if the command is not used.
#
# You can specify 'saved' instead of a number. In this case, the default entry
# is the entry saved with the command 'savedefault'.
# WARNING: If you are using dmraid do not change this entry to 'saved' or your
# array will desync and will not let you boot your system.
default 0
## timeout sec
# Set a timeout, in SEC seconds, before automatically booting the default entry
# (normally the first entry defined).
timeout 3
# Pretty colours
color cyan/blue white/blue
## password ['--md5'] passwd
# If used in the first section of a menu file, disable all interactive editing
# control (menu entry editor and command-line) and entries protected by the
# command 'lock'
# e.g. password topsecret
## password --md5 $1$gLhU0/$aW78kHK1QfV3P2b2znUoe/
# password topsecret
#A splash image for the menu
splashimage=(hd0,1)/boot/grub/splashimages/debian_grey1-14col.xpm.gz
#
# examples
#
# title Windows 95/98/NT/2000
# root (hd0,0)
# makeactive
# chainloader +1
#
# title Linux
# root (hd0,1)
# kernel /vmlinuz root=/dev/hda2 ro
#
#
# Put static boot stanzas before and/or after AUTOMAGIC KERNEL LIST
### BEGIN AUTOMAGIC KERNELS LIST
## lines between the AUTOMAGIC KERNELS LIST markers will be modified
## by the debian update-grub script except for the default options below
## DO NOT UNCOMMENT THEM, Just edit them to your needs
## ## Start Default Options ##
## default kernel options
## default kernel options for automagic boot options
## If you want special options for specific kernels use kopt_x_y_z
## where x.y.z is kernel version. Minor versions can be omitted.
## e.g. kopt=root=/dev/hda1 ro
## kopt_2_6_8=root=/dev/hdc1 ro
## kopt_2_6_8_2_686=root=/dev/hdc2 ro
# kopt=root=/dev/sda2 ro notsc
## default grub root device
## e.g. groot=(hd0,0)
# groot=(hd0,1)
## should update-grub create alternative automagic boot options
## e.g. alternative=true
## alternative=false
# alternative=true
## should update-grub lock alternative automagic boot options
## e.g. lockalternative=true
## lockalternative=false
# lockalternative=false
## additional options to use with the default boot option, but not with the
## alternatives
## e.g. defoptions=vga=791 resume=/dev/hda5
# defoptions=vga=0
## should update-grub lock old automagic boot options
## e.g. lockold=false
## lockold=true
# lockold=false
## Xen hypervisor options to use with the default Xen boot option
# xenhopt=
## Xen Linux kernel options to use with the default Xen boot option
# xenkopt=console=tty0
## altoption boot targets option
## multiple altoptions lines are allowed
## e.g. altoptions=(extra menu suffix) extra boot options
## altoptions=(single-user) single
# altoptions=(single-user mode) single
## controls how many kernels should be put into the menu.lst
## only counts the first occurence of a kernel, not the
## alternative kernel options
## e.g. howmany=all
## howmany=7
# howmany=all
## should update-grub create memtest86 boot option
## e.g. memtest86=true
## memtest86=false
# memtest86=false
## should update-grub adjust the value of the default booted system
## can be true or false
# updatedefaultentry=false
## should update-grub add savedefault to the default options
## can be true or false
# savedefault=false
## ## End Default Options ##
title Debian GNU/Linux, kernel 2.6.30-2-amd64
root (hd0,1)
kernel /boot/vmlinuz-2.6.30-2-amd64 root=/dev/sda2 ro notsc vga=0
initrd /boot/initrd.img-2.6.30-2-amd64
title Debian GNU/Linux, kernel 2.6.30-2-amd64 (single-user mode)
root (hd0,1)
kernel /boot/vmlinuz-2.6.30-2-amd64 root=/dev/sda2 ro notsc single
initrd /boot/initrd.img-2.6.30-2-amd64
title Debian GNU/Linux, kernel 2.6.30-1-amd64
root (hd0,1)
kernel /boot/vmlinuz-2.6.30-1-amd64 root=/dev/sda2 ro notsc vga=0
initrd /boot/initrd.img-2.6.30-1-amd64
title Debian GNU/Linux, kernel 2.6.30-1-amd64 (single-user mode)
root (hd0,1)
kernel /boot/vmlinuz-2.6.30-1-amd64 root=/dev/sda2 ro notsc single
initrd /boot/initrd.img-2.6.30-1-amd64
title Debian GNU/Linux, kernel 2.6.26-2-amd64
root (hd0,1)
kernel /boot/vmlinuz-2.6.26-2-amd64 root=/dev/sda2 ro notsc vga=0
initrd /boot/initrd.img-2.6.26-2-amd64
title Debian GNU/Linux, kernel 2.6.26-2-amd64 (single-user mode)
root (hd0,1)
kernel /boot/vmlinuz-2.6.26-2-amd64 root=/dev/sda2 ro notsc single
initrd /boot/initrd.img-2.6.26-2-amd64
title Debian GNU/Linux, kernel 2.6.26-1-amd64
root (hd0,1)
kernel /boot/vmlinuz-2.6.26-1-amd64 root=/dev/sda2 ro notsc vga=0
initrd /boot/initrd.img-2.6.26-1-amd64
title Debian GNU/Linux, kernel 2.6.26-1-amd64 (single-user mode)
root (hd0,1)
kernel /boot/vmlinuz-2.6.26-1-amd64 root=/dev/sda2 ro notsc single
initrd /boot/initrd.img-2.6.26-1-amd64
title Debian GNU/Linux, kernel 2.6.25-2-amd64
root (hd0,1)
kernel /boot/vmlinuz-2.6.25-2-amd64 root=/dev/sda2 ro notsc vga=0
initrd /boot/initrd.img-2.6.25-2-amd64
title Debian GNU/Linux, kernel 2.6.25-2-amd64 (single-user mode)
root (hd0,1)
kernel /boot/vmlinuz-2.6.25-2-amd64 root=/dev/sda2 ro notsc single
initrd /boot/initrd.img-2.6.25-2-amd64
### END DEBIAN AUTOMAGIC KERNELS LIST
Reply to: