against which package to report this regression bug: sound does not work in lenny, but work in etch on notebook toshiba satellite a30
Hi all
I have very strange problem with sound. Sound does not work in Debian
Lenny, but works in Debian Etch. Hardware is Toshiba Satellite a30
(lspci in attachment), with sound card ATI Technologies Inc IXP150 AC'97
Audio Controller.
Often the very first time I start playing music after reboot on Debian
Lenny, sound works for certain period of time. Second time xfmedia
hangs, mplayer prints out following in loop:
[AO_ALSA] alsa-lib: pcm_hw.c:405:(snd_pcm_hw_hwsync)
SNDRV_PCM_IOCTL_HWSYNC failed: Broken pipe
This does not happen in Debian Etch.
My first idea was that this is kernel problem. During boot I got
following suspicious messages (full dmesg is in attachment):
MP-BIOS bug: 8254 timer not connected to IO-APIC
..trying to set up timer (IRQ0) through the 8259A ... failed.
...trying to set up timer as Virtual Wire IRQ... works.
[snip]
atiixp: codec reset timeout
atiixp-modem: no codec available
After some experimenting with kernel boot options, I found out that
sound works with option "acpi=off". Other options, like noapic,
acpi={noirq,strict,force}, pci=noacpi, nolapic_timer do not help.
Using acpi=off is not a very nice solution, because it switches off
other usefull for notebook features.
Suspicious kernel messages mentioned above, appear also with option
"acpi=off".
Installing kernel 2.6.29 (from lenny-backports) does not help.
Additionaly 2.6.29 locks up after some time.
I installed Debian Etch on separate partition and there sound works
without any problem. It work with both 2.6.18 and 2.6.24.
So, I installed kernel 2.6.18 and 2.6.24 from Etch in to the Debian
Lenny (just added etch into sources.list and installed). And this does
not help! I got same sound problems in Debian Lenny with kernels 2.6.18
and 2.6.24 from Etch!
So, it looks like it is not a kernel problem. But I do not know where to
look for a problem now and I do not know against which package should I
report this regression bug.
Please put me on CC when you reply to this message.
--
Best regards, Sergey Spiridonov
00:00.0 Host bridge: ATI Technologies Inc RS300 Host Bridge (rev 02)
00:01.0 PCI bridge: ATI Technologies Inc Radeon 9100 IGP AGP Bridge
00:13.0 USB Controller: ATI Technologies Inc OHCI USB Controller #1 (rev 01)
00:13.1 USB Controller: ATI Technologies Inc OHCI USB Controller #2 (rev 01)
00:13.2 USB Controller: ATI Technologies Inc EHCI USB Controller (rev 01)
00:14.0 SMBus: ATI Technologies Inc SMBus (rev 17)
00:14.1 IDE interface: ATI Technologies Inc Dual Channel Bus Master PCI IDE Controller
00:14.3 ISA bridge: ATI Technologies Inc Device 434c
00:14.4 PCI bridge: ATI Technologies Inc IXP200 3COM 3C920B Ethernet Controller
00:14.5 Multimedia audio controller: ATI Technologies Inc IXP150 AC'97 Audio Controller
00:14.6 Modem: ATI Technologies Inc IXP AC'97 Modem (rev 01)
01:05.0 VGA compatible controller: ATI Technologies Inc RS300M AGP [Radeon Mobility 9100IGP]
02:00.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21 IEEE-1394a-2000 Controller (PHY/Link)
02:03.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
02:04.0 CardBus bridge: ENE Technology Inc CB1410 Cardbus Controller (rev 01)
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.26-2-686 (Debian 2.6.26-15lenny3) (dannf@debian.org) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 SMP Thu May 28 15:39:35 UTC 2009
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000d0000 - 00000000000d8000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000001bf60000 (usable)
[ 0.000000] BIOS-e820: 000000001bf60000 - 000000001bf6d000 (ACPI data)
[ 0.000000] BIOS-e820: 000000001bf6d000 - 000000001bf80000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000001bf80000 - 000000001c000000 (reserved)
[ 0.000000] BIOS-e820: 000000002bf80000 - 000000002c000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 447MB LOWMEM available.
[ 0.000000] found SMP MP-table at [c00f6700] 000f6700
[ 0.000000] Entering add_active_range(0, 0, 114528) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 114528
[ 0.000000] HighMem 114528 -> 114528
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 114528
[ 0.000000] On node 0 totalpages: 114528
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 863 pages used for memmap
[ 0.000000] Normal zone: 109569 pages, LIFO batch:31
[ 0.000000] HighMem zone: 0 pages used for memmap
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI present.
[ 0.000000] ACPI: RSDP 000F6770, 0014 (r0 PTLTD )
[ 0.000000] ACPI: RSDT 1BF68101, 0038 (r1 PTLTD RSDT 6040000 LTP 0)
[ 0.000000] ACPI: FACP 1BF6CF32, 0074 (r1 TOSCPL Chinook 6040000 ATI 3)
[ 0.000000] ACPI: DSDT 1BF689B5, 457D (r1 TOSCPL SB200 6040000 MSFT 100000E)
[ 0.000000] ACPI: FACS 1BF7FFC0, 0040
[ 0.000000] ACPI: APIC 1BF6CFA6, 005A (r1 PTLTD APIC 6040000 LTP 0)
[ 0.000000] ACPI: SSDT 1BF68540, 032B (r1 PmRef Cpu0Ist 3000 INTL 20030224)
[ 0.000000] ACPI: SSDT 1BF68334, 020C (r1 PmRef Cpu0Cst 3001 INTL 20030224)
[ 0.000000] ACPI: SSDT 1BF68139, 01FB (r1 PmRef CpuPm 3000 INTL 20030224)
[ 0.000000] ACPI: DMI detected: Toshiba
[ 0.000000] ATI board detected. Disabling timer routing over 8254.
[ 0.000000] ACPI: PM-Timer IO Port: 0x8008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 17, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 30000000 (gap: 2c000000:d2c00000)
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000d0000
[ 0.000000] PM: Registered nosave memory: 00000000000d0000 - 00000000000d8000
[ 0.000000] PM: Registered nosave memory: 00000000000d8000 - 00000000000e4000
[ 0.000000] PM: Registered nosave memory: 00000000000e4000 - 0000000000100000
[ 0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs
[ 0.000000] PERCPU: Allocating 37960 bytes of per cpu data
[ 0.000000] NR_CPUS: 8, nr_cpu_ids: 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 113633
[ 0.000000] Kernel command line: root=/dev/mapper/messenger_main-root ro quiet
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[ 0.000000] Detected 1600.141 MHz processor.
[ 0.004000] Console: colour VGA+ 80x25
[ 0.004000] console [tty0] enabled
[ 0.004000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.004000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.004000] Memory: 442948k/458112k available (1769k kernel code, 14644k reserved, 752k data, 244k init, 0k highmem)
[ 0.004000] virtual kernel memory layout:
[ 0.004000] fixmap : 0xfff4c000 - 0xfffff000 ( 716 kB)
[ 0.004000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.004000] vmalloc : 0xdc800000 - 0xff7fe000 ( 559 MB)
[ 0.004000] lowmem : 0xc0000000 - 0xdbf60000 ( 447 MB)
[ 0.004000] .init : 0xc037f000 - 0xc03bc000 ( 244 kB)
[ 0.004000] .data : 0xc02ba5eb - 0xc0376620 ( 752 kB)
[ 0.004000] .text : 0xc0100000 - 0xc02ba5eb (1769 kB)
[ 0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.004000] CPA: page pool initialized 1 of 1 pages preallocated
[ 0.084163] Calibrating delay using timer specific routine.. 3204.15 BogoMIPS (lpj=6408304)
[ 0.084228] Security Framework initialized
[ 0.084236] SELinux: Disabled at boot.
[ 0.084243] Capability LSM initialized
[ 0.084270] Mount-cache hash table entries: 512
[ 0.084532] Initializing cgroup subsys ns
[ 0.084540] Initializing cgroup subsys cpuacct
[ 0.084545] Initializing cgroup subsys devices
[ 0.084580] CPU: Trace cache: 12K uops, L1 D cache: 8K
[ 0.084586] CPU: L2 cache: 512K
[ 0.084590] CPU: Hyper-Threading is disabled
[ 0.084596] Intel machine check architecture supported.
[ 0.084606] Intel machine check reporting enabled on CPU#0.
[ 0.084611] CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
[ 0.084618] CPU0: Thermal monitoring enabled
[ 0.084643] Checking 'hlt' instruction... OK.
[ 0.100634] SMP alternatives: switching to UP code
[ 0.115372] Freeing SMP alternatives: 16k freed
[ 0.115380] ACPI: Core revision 20080321
[ 0.134264] ENABLING IO-APIC IRQs
[ 0.134458] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.136008] ..MP-BIOS bug: 8254 timer not connected to IO-APIC
[ 0.136008] ...trying to set up timer (IRQ0) through the 8259A ... failed.
[ 0.136008] ...trying to set up timer as Virtual Wire IRQ... works.
[ 0.177927] CPU0: Intel Mobile Intel(R) Pentium(R) 4 CPU 2.40GHz stepping 09
[ 0.180011] Brought up 1 CPUs
[ 0.180011] Total of 1 processors activated (3204.15 BogoMIPS).
[ 0.180011] CPU0 attaching sched-domain:
[ 0.180011] domain 0: span 0
[ 0.180011] groups: 0
[ 0.180011] net_namespace: 660 bytes
[ 0.180011] Booting paravirtualized kernel on bare hardware
[ 0.180011] NET: Registered protocol family 16
[ 0.180011] ACPI: bus type pci registered
[ 0.264016] PCI: PCI BIOS revision 2.10 entry at 0xfd958, last bus=2
[ 0.264016] PCI: Using configuration type 1 for base access
[ 0.264016] Setting up standard PCI resources
[ 0.268801] ACPI: EC: Look up EC in DSDT
[ 0.273414] ACPI: Interpreter enabled
[ 0.273422] ACPI: (supports S0 S3 S4 S5)
[ 0.273448] ACPI: Using IOAPIC for interrupt routing
[ 0.317701] ACPI: EC: GPE = 0x6, I/O: command/status = 0x66, data = 0x62
[ 0.317707] ACPI: EC: driver started in poll mode
[ 0.317791] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.318710] PCI: Transparent bridge - 0000:00:14.4
[ 0.318758] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.318986] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
[ 0.319233] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
[ 0.322585] ACPI: PCI Interrupt Link [LNK0] (IRQs 10 11) *0, disabled.
[ 0.322777] ACPI: PCI Interrupt Link [LNK1] (IRQs 10 11) *0, disabled.
[ 0.322965] ACPI: PCI Interrupt Link [LNK2] (IRQs 10 11) *0, disabled.
[ 0.323151] ACPI: PCI Interrupt Link [LNK3] (IRQs 10 11) *0, disabled.
[ 0.323574] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.323635] pnp: PnP ACPI init
[ 0.323651] ACPI: bus type pnp registered
[ 0.348208] pnp: PnP ACPI: found 9 devices
[ 0.348215] ACPI: ACPI bus type pnp unregistered
[ 0.348221] PnPBIOS: Disabled by ACPI PNP
[ 0.348725] PCI: Using ACPI for IRQ routing
[ 0.349008] ACPI: RTC can wake from S4
[ 0.349065] system 00:07: ioport range 0x1080-0x1080 has been reserved
[ 0.349071] system 00:07: ioport range 0x200-0x20f has been reserved
[ 0.349076] system 00:07: ioport range 0x220-0x22f has been reserved
[ 0.349080] system 00:07: ioport range 0x40b-0x40b has been reserved
[ 0.349085] system 00:07: ioport range 0x4d0-0x4d1 has been reserved
[ 0.349089] system 00:07: ioport range 0x4d6-0x4d6 has been reserved
[ 0.349094] system 00:07: ioport range 0x530-0x537 has been reserved
[ 0.349099] system 00:07: ioport range 0xc00-0xc01 has been reserved
[ 0.349103] system 00:07: ioport range 0xc14-0xc14 has been reserved
[ 0.349111] system 00:07: ioport range 0xc50-0xc52 has been reserved
[ 0.349115] system 00:07: ioport range 0xc6c-0xc6c has been reserved
[ 0.349120] system 00:07: ioport range 0xc6f-0xc6f has been reserved
[ 0.349125] system 00:07: ioport range 0xcd6-0xcd7 has been reserved
[ 0.349130] system 00:07: ioport range 0x8000-0x805f has been reserved
[ 0.349135] system 00:07: ioport range 0xfe00-0xfe00 has been reserved
[ 0.349140] system 00:07: ioport range 0xfe10-0xfe11 has been reserved
[ 0.349153] system 00:08: iomem range 0x0-0x9ffff could not be reserved
[ 0.349159] system 00:08: iomem range 0xe0000-0xfffff could not be reserved
[ 0.349164] system 00:08: iomem range 0x100000-0x1bffffff could not be reserved
[ 0.349170] system 00:08: iomem range 0xfff80000-0xffffffff could not be reserved
[ 0.349175] system 00:08: iomem range 0xe8000000-0xe8000fff has been reserved
[ 0.379898] PCI: region 0000:02:04.0/9 too large: 0x0000000000000000-0x0000000003ffffff
[ 0.379911] PCI: Bridge: 0000:00:01.0
[ 0.379916] IO window: 9000-9fff
[ 0.379922] MEM window: 0xe8100000-0xe81fffff
[ 0.379928] PREFETCH window: 0x00000000f0000000-0x00000000f7ffffff
[ 0.379942] PCI: Bus 3, cardbus bridge: 0000:02:04.0
[ 0.379945] IO window: 0x0000a400-0x0000a4ff
[ 0.379952] IO window: 0x0000a800-0x0000a8ff
[ 0.379958] MEM window: 0x30000000-0x33ffffff
[ 0.379964] PCI: Bridge: 0000:00:14.4
[ 0.379968] IO window: a000-afff
[ 0.379974] MEM window: 0xe8200000-0xe82fffff
[ 0.379978] PREFETCH window: disabled.
[ 0.380034] ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 0.380084] NET: Registered protocol family 2
[ 0.380266] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.380621] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.380751] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.380877] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.380883] TCP reno registered
[ 0.381013] NET: Registered protocol family 1
[ 0.381222] checking if image is initramfs...<7>Switched to high resolution mode on CPU 0
[ 0.899701] it is
[ 1.483804] Freeing initrd memory: 7356k freed
[ 1.485005] audit: initializing netlink socket (disabled)
[ 1.485035] type=2000 audit(1245532913.484:1): initialized
[ 1.485237] Total HugeTLB memory allocated, 0
[ 1.485355] VFS: Disk quotas dquot_6.5.1
[ 1.485403] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.485467] msgmni has been set to 879
[ 1.485655] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 1.485662] io scheduler noop registered
[ 1.485665] io scheduler anticipatory registered
[ 1.485669] io scheduler deadline registered
[ 1.485689] io scheduler cfq registered (default)
[ 2.014435] pci 0000:01:05.0: Boot video device
[ 2.015045] isapnp: Scanning for PnP cards...
[ 2.366284] isapnp: No Plug & Play device found
[ 2.370961] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 2.371673] ACPI: PCI Interrupt 0000:00:14.6[B] -> GSI 17 (level, low) -> IRQ 17
[ 2.371684] ACPI: PCI interrupt for device 0000:00:14.6 disabled
[ 2.374223] brd: module loaded
[ 2.374397] PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
[ 2.387438] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 2.395042] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.395051] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 2.395056] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 2.395063] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 2.395067] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 2.395359] mice: PS/2 mouse device common for all mice
[ 2.395850] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 2.395870] rtc0: alarms up to one day
[ 2.395933] cpuidle: using governor ladder
[ 2.395938] cpuidle: using governor menu
[ 2.395947] No iBFT detected.
[ 2.396730] TCP cubic registered
[ 2.396736] NET: Registered protocol family 17
[ 2.396748] Using IPI No-Shortcut mode
[ 2.396766] registered taskstats version 1
[ 2.396766] rtc_cmos 00:03: setting system clock to 2009-06-20 21:21:55 UTC (1245532915)
[ 2.396766] Freeing unused kernel memory: 244k freed
[ 2.430996] input: AT Translated Set 2 keyboard as /class/input/input0
[ 2.593975] ACPI: CPU0 (power states: C1[C1] C2[C2])
[ 2.594065] ACPI: ACPI0007:00 is registered as cooling_device0
[ 2.594073] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 3.214114] usbcore: registered new interface driver usbfs
[ 3.214169] usbcore: registered new interface driver hub
[ 3.214230] usbcore: registered new device driver usb
[ 3.222394] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 3.222440] ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 19
[ 3.222465] ohci_hcd 0000:00:13.0: OHCI Host Controller
[ 3.222661] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
[ 3.222697] ohci_hcd 0000:00:13.0: irq 19, io mem 0xe8001000
[ 3.226873] Linux agpgart interface v0.103
[ 3.280190] usb usb1: configuration #1 chosen from 1 choice
[ 3.280248] hub 1-0:1.0: USB hub found
[ 3.280268] hub 1-0:1.0: 3 ports detected
[ 3.384257] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.384265] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.384271] usb usb1: Product: OHCI Host Controller
[ 3.384275] usb usb1: Manufacturer: Linux 2.6.26-2-686 ohci_hcd
[ 3.384279] usb usb1: SerialNumber: 0000:00:13.0
[ 3.384327] agpgart: Detected Ati IGP9100/M chipset
[ 3.387614] agpgart: AGP aperture is 32M @ 0xea000000
[ 3.387665] ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 19
[ 3.387683] ohci_hcd 0000:00:13.1: OHCI Host Controller
[ 3.387727] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2
[ 3.387764] ohci_hcd 0000:00:13.1: irq 19, io mem 0xe8002000
[ 3.444187] usb usb2: configuration #1 chosen from 1 choice
[ 3.444249] hub 2-0:1.0: USB hub found
[ 3.444265] hub 2-0:1.0: 3 ports detected
[ 3.548240] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.548248] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.548253] usb usb2: Product: OHCI Host Controller
[ 3.548256] usb usb2: Manufacturer: Linux 2.6.26-2-686 ohci_hcd
[ 3.548260] usb usb2: SerialNumber: 0000:00:13.1
[ 3.548416] ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 19
[ 3.548447] ehci_hcd 0000:00:13.2: EHCI Host Controller
[ 3.548494] ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3
[ 3.548552] ehci_hcd 0000:00:13.2: irq 19, io mem 0xe8003000
[ 3.688050] usb 1-2: new low speed USB device using ohci_hcd and address 2
[ 3.700070] ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 3.700228] usb usb3: configuration #1 chosen from 1 choice
[ 3.700283] hub 3-0:1.0: USB hub found
[ 3.700302] hub 3-0:1.0: 6 ports detected
[ 3.756061] hub 1-0:1.0: unable to enumerate USB device on port 2
[ 3.791972] No dock devices found.
[ 3.806424] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 3.806432] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.806437] usb usb3: Product: EHCI Host Controller
[ 3.806441] usb usb3: Manufacturer: Linux 2.6.26-2-686 ehci_hcd
[ 3.806445] usb usb3: SerialNumber: 0000:00:13.2
[ 3.880552] SCSI subsystem initialized
[ 3.991611] libata version 3.00 loaded.
[ 4.076903] Uniform Multi-Platform E-IDE driver
[ 4.076914] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 4.089232] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 4.139116] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[16] MMIO=[e8204000-e82047ff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 4.143148] 8139too Fast Ethernet driver 0.9.28
[ 4.253009] ATIIXP: IDE controller (0x1002:0x4349 rev 0x00) at PCI slot 0000:00:14.1
[ 4.253026] ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 16
[ 4.253043] ATIIXP: not 100% native mode: will probe irqs later
[ 4.253057] ide0: BM-DMA at 0x8070-0x8077
[ 4.253068] ide1: BM-DMA at 0x8078-0x807f
[ 4.253076] Probing IDE interface ide0...
[ 4.262179] ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 19 (level, low) -> IRQ 19
[ 4.263125] eth0: RealTek RTL8139 at 0xa000, 00:02:3f:d2:04:bf, IRQ 19
[ 4.263130] eth0: Identified 8139 chip type 'RTL-8101'
[ 4.268452] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 4.468061] usb 3-3: new high speed USB device using ehci_hcd and address 3
[ 4.539578] Marking TSC unstable due to: TSC halts in idle.
[ 4.540241] hda: SAMSUNG HM160HC, ATA DISK drive
[ 4.733091] usb 3-3: configuration #1 chosen from 1 choice
[ 4.733091] usb 3-3: New USB device found, idVendor=067b, idProduct=3507
[ 4.733091] usb 3-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4.733091] usb 3-3: Product: ATAPI-6 Bridge Controller
[ 4.733091] usb 3-3: Manufacturer: Prolific Technology Inc.
[ 4.733091] usb 3-3: SerialNumber: 261E
[ 4.776586] Initializing USB Mass Storage driver...
[ 5.036032] usb 1-2: new low speed USB device using ohci_hcd and address 3
[ 5.212114] hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
[ 5.212195] hda: UDMA/100 mode selected
[ 5.212271] Probing IDE interface ide1...
[ 5.250590] usb 1-2: configuration #1 chosen from 1 choice
[ 5.252920] usb 1-2: New USB device found, idVendor=04d9, idProduct=1133
[ 5.252928] usb 1-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 5.253150] scsi0 : SCSI emulation for USB Mass Storage devices
[ 5.253331] usbcore: registered new interface driver usb-storage
[ 5.253338] USB Mass Storage support registered.
[ 5.257409] usb-storage: device found at 3
[ 5.257415] usb-storage: waiting for device to settle before scanning
[ 5.330566] usbcore: registered new interface driver hiddev
[ 5.342584] input: HID 04d9:1133 as /class/input/input1
[ 5.342584] input,hidraw0: USB HID v1.10 Mouse [HID 04d9:1133] on usb-0000:00:13.0-2
[ 5.342584] usbcore: registered new interface driver usbhid
[ 5.342584] usbhid: v2.6:USB HID core driver
[ 5.524242] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00023f414b001588]
[ 5.780126] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 5.798226] ide1 at 0x170-0x177,0x376 on irq 15
[ 5.845589] hda: max request size: 512KiB
[ 5.847618] hda: 312581808 sectors (160041 MB) w/8192KiB Cache, CHS=19457/255/63
[ 5.849344] hda: cache flushes supported
[ 5.849344] hda: hda1 hda2 hda3
[ 6.161455] device-mapper: uevent: version 1.0.3
[ 6.163553] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com
[ 6.433971] PM: Starting manual resume from disk
[ 6.487230] kjournald starting. Commit interval 5 seconds
[ 6.487230] EXT3-fs: mounted filesystem with ordered data mode.
[ 8.111065] udevd version 125 started
[ 10.256259] usb-storage: device scan complete
[ 10.257971] scsi 0:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-H44N RB01 PQ: 0 ANSI: 0
[ 10.440036] Driver 'sr' needs updating - please use bus_type methods
[ 10.444970] sr0: scsi3-mmc drive: 125x/125x writer dvd-ram cd/rw xa/form2 cdda tray
[ 10.444981] Uniform CD-ROM driver Revision: 3.20
[ 10.445157] sr 0:0:0:0: Attached scsi CD-ROM sr0
[ 10.518700] sr 0:0:0:0: Attached scsi generic sg0 type 5
[ 86.717024] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 86.736128] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 87.055158] piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device
[ 87.840056] input: Power Button (FF) as /class/input/input2
[ 87.869253] ACPI: Power Button (FF) [PWRF]
[ 87.869375] input: Lid Switch as /class/input/input3
[ 87.882347] ACPI: Lid Switch [LID]
[ 87.882476] input: Power Button (CM) as /class/input/input4
[ 87.909746] ACPI: Power Button (CM) [PWRB]
[ 87.950103] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 87.972854] ACPI: AC Adapter [ACAD] (on-line)
[ 88.696327] ACPI: Battery Slot [BAT1] (battery present)
[ 88.990017] input: Video Bus as /class/input/input5
[ 89.018539] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 89.266752] input: PC Speaker as /class/input/input6
[ 89.956706] Yenta: CardBus bridge found at 0000:02:04.0 [1179:ff00]
[ 89.956734] PCI: Bus 3, cardbus bridge: 0000:02:04.0
[ 89.956739] IO window: 0x0000a400-0x0000a4ff
[ 89.956745] IO window: 0x0000a800-0x0000a8ff
[ 89.956752] PREFETCH window: 0x34000000-0x343fffff
[ 89.956759] MEM window: 0x30000000-0x33ffffff
[ 89.956771] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 89.956774] Yenta: Routing CardBus interrupts to PCI
[ 89.956782] Yenta TI: socket 0000:02:04.0, mfunc 0x00111c12, devctl 0x44
[ 90.066214] input: PS/2 Mouse as /class/input/input7
[ 90.112762] input: AlpsPS/2 ALPS GlidePoint as /class/input/input8
[ 90.188908] Yenta: ISA IRQ mask 0x0eb0, PCI irq 16
[ 90.188916] Socket status: 30000006
[ 90.188923] pcmcia: parent PCI bridge I/O window: 0xa000 - 0xafff
[ 90.188928] cs: IO port probe 0xa000-0xafff: clean.
[ 90.189328] pcmcia: parent PCI bridge Memory window: 0xe8200000 - 0xe82fffff
[ 90.529228] ACPI: PCI Interrupt 0000:00:14.5[B] -> GSI 17 (level, low) -> IRQ 17
[ 90.530276] atiixp: codec reset timeout
[ 90.702196] ACPI: PCI Interrupt 0000:00:14.6[B] -> GSI 17 (level, low) -> IRQ 17
[ 90.708608] atiixp-modem: no codec available
[ 90.708704] ACPI: PCI interrupt for device 0000:00:14.6 disabled
[ 91.328018] cs: IO port probe 0x100-0x3af: clean.
[ 91.328018] cs: IO port probe 0x3e0-0x4ff: clean.
[ 91.328018] cs: IO port probe 0x820-0x8ff: clean.
[ 91.328018] cs: IO port probe 0xc00-0xcf7: clean.
[ 91.328018] cs: IO port probe 0xa00-0xaff: clean.
[ 92.446723] EXT3 FS on dm-1, internal journal
[ 92.780663] loop: module loaded
[ 94.288329] kjournald starting. Commit interval 5 seconds
[ 94.288488] EXT3 FS on dm-3, internal journal
[ 94.288488] EXT3-fs: mounted filesystem with ordered data mode.
[ 94.355482] Adding 2928632k swap on /dev/mapper/messenger_main-swap. Priority:-1 extents:1 across:2928632k
[ 95.645872] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[ 98.461501] NET: Registered protocol family 10
[ 98.462214] lo: Disabled Privacy Extensions
[ 98.876032] Clocksource tsc unstable (delta = 142080646 ns)
[ 100.282024] lp: driver loaded but no devices found
[ 100.335157] ppdev: user-space parallel port driver
[ 103.385503] Bluetooth: Core ver 2.11
[ 103.388116] NET: Registered protocol family 31
[ 103.388126] Bluetooth: HCI device and connection manager initialized
[ 103.388133] Bluetooth: HCI socket layer initialized
[ 103.458001] Bluetooth: L2CAP ver 2.9
[ 103.458011] Bluetooth: L2CAP socket layer initialized
[ 103.464877] Bluetooth: RFCOMM socket layer initialized
[ 103.464898] Bluetooth: RFCOMM TTY layer initialized
[ 103.464902] Bluetooth: RFCOMM ver 1.8
[ 106.205323] [drm] Initialized drm 1.1.0 20060810
[ 106.213576] ACPI: PCI Interrupt 0000:01:05.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 106.213852] [drm] Initialized radeon 1.29.0 20080528 on minor 0
[ 107.419890] agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
[ 107.419890] agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
[ 107.419890] agpgart: Putting AGP V3 device at 0000:01:05.0 into 8x mode
[ 108.657725] [drm] Setting GART location based on new memory map
[ 108.657725] [drm] Loading R200 Microcode
[ 108.657725] [drm] writeback test succeeded in 1 usecs
[ 108.860026] eth0: no IPv6 routers present
Reply to: