[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Re: SMART error (OfflineUncorrectableSector) detected on host:



2008/11/26 Paul Cartwright <ale@pcartwright.com>:

> I didn't see anything... noticeable after the short test. Not sure I
> understand all the tests.. do you need to unmount the partition for the long
> test?

No you want to see the smart data on the disc,
smartctl -d ata -a /dev/sd[0-9]

Here is one from an old disc of mine, take note of line 5 and 9 :-)
Adrian

smartctl version 5.36 [i686-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

=== START OF INFORMATION SECTION ===
Model Family:     Fujitsu MPD and MPE series
Device Model:     FUJITSU MPD3084AT
Serial Number:    01073642
Firmware Version: DD-03-47
User Capacity:    8,455,200,768 bytes
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   4
ATA Standard is:  Exact ATA specification draft version not indicated
Local Time is:    Wed Nov 26 07:02:32 2008 EST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.

General SMART Values:
Offline data collection status:  (0x82)	Offline data collection activity
					was completed without error.
					Auto Offline Data Collection: Enabled.
Total time to complete Offline
data collection: 		 (2880) seconds.
Offline data collection
capabilities: 			 (0x03) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					No Offline surface scan supported.
					No Self-test supported.
					No Conveyance Self-test supported.
					No Selective Self-test supported.
SMART capabilities:            (0x0002)	Does not save SMART data before
					entering power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x00)	Error logging NOT supported.
					No General Purpose Logging support.

SMART Attributes Data Structure revision number: 5
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE
UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000b   100   001   032    Pre-fail
Always   In_the_past 260453
  2 Throughput_Performance  0x0005   066   059   020    Pre-fail
Offline      -       136
  3 Spin_Up_Time            0x0007   093   090   025    Pre-fail
Always       -       2
  4 Start_Stop_Count        0x0012   096   096   016    Old_age
Always       -       2020
  5 Reallocated_Sector_Ct   0x0033   100   100   024    Pre-fail
Always       -       0
  7 Seek_Error_Rate         0x000b   100   100   020    Pre-fail
Always       -       2327
  8 Seek_Time_Performance   0x0005   080   080   019    Pre-fail
Offline      -       32
  9 Power_On_Seconds        0x0012   001   001   020    Old_age
Always   FAILING_NOW 30486h+31m+41s
 10 Spin_Retry_Count        0x0013   100   100   020    Pre-fail
Always       -       0
 12 Power_Cycle_Count       0x0032   087   087   020    Old_age
Always       -       1979
199 UDMA_CRC_Error_Count    0x000a   200   200   000    Old_age
Always       -       0
200 Multi_Zone_Error_Rate   0x000b   100   080   020    Pre-fail
Always       -       1173

Warning: device does not support Error Logging
Error SMART Error Log Read failed: Input/output error
Smartctl: SMART Error Log Read Failed
Warning: device does not support Self Test Logging
Error SMART Error Self-Test Log Read failed: Input/output error
Smartctl: SMART Self Test Log Read Failed
Device does not support Selective Self Tests/Logging




-- 
24x7x365 != 24x7x52 Stupid or bad maths?
<erno> hm. I've lost a machine.. literally _lost_. it responds to
ping, it works completely, I just can't figure out where in my
apartment it is.


Reply to: