Re: Hard disk dying?
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Justin, here is the output from smartctl -a /dev/hda
smartctl version 5.36 [i686-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is
http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: MAXTOR STM3160812A
Serial Number: 4LS62YAM
Firmware Version: 3.AAK
User Capacity: 160,041,885,696 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 7
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Mon Aug 6 13:50:49 2007 EDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off supp
ort.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 54) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_
FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 114 095 006 Pre-fail Always -
74351205
3 Spin_Up_Time 0x0003 093 092 000 Pre-fail Always -
0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always -
72
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always -
0
7 Seek_Error_Rate 0x000f 079 060 030 Pre-fail Always -
84026551
9 Power_On_Hours 0x0032 100 100 000 Old_age Always -
828
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always -
0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always -
82
187 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0
189 Unknown_Attribute 0x003a 100 100 000 Old_age Always -
0
190 Unknown_Attribute 0x0022 065 055 045 Old_age Always -
740425763
194 Temperature_Celsius 0x0022 035 045 000 Old_age Always -
35 (Lifetime Min/Max 0/11)
195 Hardware_ECC_Recovered 0x001a 056 048 000 Old_age Always -
6712323
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always -
0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline -
0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always -
26
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline -
0
202 TA_Increase_Count 0x0032 100 253 000 Old_age Always -
0
SMART Error Log Version: 1
ATA Error Count: 39 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after
49.710 days.
Error 39 occurred at disk power-on lifetime: 19 hours (0 days + 19 hours)
When the command that caused the error occurred, the device was active or idle
.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 00 00 00 e0 00 00:01:02.122 READ DMA EXT
25 00 08 00 00 00 e0 00 00:01:
05.759 READ DMA EXT
10 00 3f 00 00 00 e0 00 00:01:05.309 RECALIBRATE [OBS-4]
25 00 08 00 00 00 e0 00 00:01:05.309 READ DMA EXT
25 00 08 00 00 00 e0 00 00:01:04.858 READ DMA EXT
Error 38 occurred at disk power-on lifetime: 19 hours (0 days + 19 hours)
When the command that caused the error occurred, the device was active or idle
.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 00 00 00 e0 00 00:01:02.122 READ DMA EXT
10 00 3f 00 00 00 e0 00 00:01:
02.091 RECALIBRATE [OBS-4]
25 00 08 00 00 00 e0 00 00:01:05.309 READ DMA EXT
25 00 08 00 00 00 e0 00 00:01:05.309 READ DMA EXT
25 00 08 00 00 00 e0 00 00:01:04.858 READ DMA EXT
Error 37 occurred at disk power-on lifetime: 19 hours (0 days + 19 hours)
When the command that caused the error occurred, the device was active or idle
.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 00 00 00 e0 00 00:01:02.122 READ DMA EXT
25 00 08 00 00 00 e0 00 00:01:
02.091 READ DMA EXT
25 00 08 00 00 00 e0 00 00:01:02.072 READ DMA EXT
c6 00 10 00 00 00 e0 00 00:01:01.621 SET MULTIPLE MODE
00 00 40 00 00 00 00 06 00:01:04.858 NOP [Abort queued commands]
Error 36 occurred at disk power-on lifetime: 19 hours (0 days + 19 hours)
When the command that caused the error occurred, the device was active or idle
.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 00 00 00 e0 00 00:01:02.122 READ DMA EXT
25 00 08 00 00 00 e0 00 00:01:
02.091 READ DMA EXT
c6 00 10 00 00 00 e0 00 00:01:02.072 SET MULTIPLE MODE
00 00 40 00 00 00 00 06 00:01:01.621 NOP [Abort queued commands]
ef 03 40 00 00 00 e0 02 00:01:01.171 SET FEATURES [Set transfer mode]
Error 35 occurred at disk power-on lifetime: 19 hours (0 days + 19 hours)
When the command that caused the error occurred, the device was active or idle
.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 00 00 00 e0 00 00:01:02.122 READ DMA EXT
c6 00 10 00 00 00 e0 00 00:01:
02.091 SET MULTIPLE MODE
00 00 40 00 00 00 00 06 00:01:02.072 NOP [Abort queued commands]
ef 03 40 00 00 00 e0 02 00:01:01.621 SET FEATURES [Set transfer mode]
25 00 08 00 00 00 e0 00 00:01:
01.171 READ DMA EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA
_of_first_error
# 1 Extended offline Completed without error 00% 812 -
# 2 Extended offline Completed without error 00% 825 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Thanks,
Sam
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.6 (GNU/Linux)
Comment: http://firegpg.tuxfamily.org
iD8DBQFGt2FyMwtNS8TLpaIRAr3vAKDZJ1lS5mh3nooBO6U42lQX5BXk6wCfXUTL
kFNyy2fRShyO0BVy1vVIcXs=
=vKd7
-----END PGP SIGNATURE-----
On 8/6/07, Justin Piszcz <jpiszcz@lucidpixels.com
> wrote:
On Mon, 6 Aug 2007, David Brodbeck wrote:
>
> On Aug 6, 2007, at 9:56 AM, Sam wrote:
>
>> Hi All,
>> I noticed this in dmesg the other day
>>
>> hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
>> hda: drive_cmd: error=0x04 { DriveStatusError }
>> ide: failed opcode was: 0xb0
>>
>> and i have started to get corrupted data off of it. I assume it is dying,
>> but thought to ask, as its rather new ( Power On Hours 827) its a maxtor
>> 160gb.
>
> Time to file a warranty claim, I'm guessing. Maxtor has their own test
> utility, which you might as well download because they'll want an error code
> from it before they do an exchange.
>
>
Use smartctl:
smartctl -a /dev/hda
What does this show?
--
To UNSUBSCRIBE, email to debian-user-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
Reply to: