Problems with cdrecord under kernel 2.6.15-8
Since doing an upgrade to testing, I can no longer burn CDs using any
tool in my arsenal, although DVDs continue to burn correctly. When
trying to burn CDs, I get lots of errors similar to the following:
cdrecord: Warning: Running on Linux-2.6.15-1-686
cdrecord: There are unsettled issues with Linux-2.5 and newer.
cdrecord: If you have unexpected problems, please try Linux-2.4 or Solaris.
TOC Type: 1 = CD-ROM
scsidev: '0,0,0'
scsibus: 0 target: 0 lun: 0
Linux sg driver version: 3.5.33
Using libscg version 'schily-0.8'.
SCSI buffer size: 64512
atapi: 1
Device type : Removable CD-ROM
Version : 0
Response Format: 2
Capabilities :
Vendor_info : '_NEC '
Identifikation : 'DVD_RW ND-1300A '
Revision : '1.06'
Device seems to be: Generic mmc2 DVD-R/DVD-RW.
Current: 0x0009
Profile: 0x001B
Profile: 0x001A
Profile: 0x0014
Profile: 0x0013
Profile: 0x0011
Profile: 0x0010
Profile: 0x000A
Profile: 0x0009 (current)
Profile: 0x0008 (current)
cdrecord: This version of cdrecord does not include DVD-R/DVD-RW support code.
cdrecord: See /usr/share/doc/cdrecord/README.DVD.Debian for details on DVD support.
Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr).
Driver flags : MMC-3 SWABAUDIO BURNFREE
Supported modes: TAO PACKET SAO SAO/R96R RAW/R96R
Drive buf size : 1345536 = 1314 KB
FIFO size : 4194304 = 4096 KB
Track 01: data 3 MB
Total size: 4 MB (00:26.69) = 2002 sectors
Lout start: 4 MB (00:28/52) = 2002 sectors
Current Secsize: 2048
ATIP info from disk:
Indicated writing power: 5
Is not unrestricted
Is not erasable
Disk sub type: Medium Type A, low Beta category (A-) (2)
ATIP start of lead in: -11634 (97:26/66)
ATIP start of lead out: 107849 (23:59/74)
Disk type: Short strategy type (Phthalocyanine or similar)
Manuf. index: 3
Manufacturer: CMC Magnetics Corporation
Blocks total: 107849 Blocks current: 107849 Blocks remaining: 105847
Starting to write CD/DVD at speed 16 in real TAO mode for single session.
Last chance to quit, starting real write 0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
BURN-Free is ON.
Turning BURN-Free off
Performing OPC...
cdrecord: Input/output error. send opc: scsi sendcmd: no error
CDB: 54 01 00 00 00 00 00 00 00 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 03 00 1C A3 80 0A 00 00 00 00 0C 00 00 00
Sense Key: 0x3 Medium Error, Segment 0
Sense Code: 0x0C Qual 0x00 (write error) Fru 0x0
Sense flags: Blk 1876864 (not valid)
cmd finished after 2.135s timeout 60s
cdrecord: OPC failed.
Writing time: 2.290s
cdrecord: fifo had 64 puts and 0 gets.
cdrecord: fifo was 0 times empty and 0 times full, min fill was 100%.
The kernel doesn't seem to include modules for ide-scsi anymore, and I
have to manually load sg.o with "sudo modprobe sg" before cdrecord will
even find the device. What's weird, though, is that burning DVDs on the
same device still works.
What gives?
--
Re-Interpreting Historic Miracles with SED #141: %s/water/wine/g
Reply to: