problem using Canon SD400 on Debian Sarge
Hello,
I recently got a Canon SD400 camera. I have been trying to get it to
work with my laptop which runs Debian Sarge but no luck yet :-( I am
running kernel version 2.6.12-1-686. I have usb storage working fine.
I can use USB hard disks and other kinds of memory sticks by mounting
them onto /dev/sda1 ... Coming to the peculiar problem which I face
with the camera ...
As soon as I plug the camera in, for a brief period it is reported by
`lsusb' (from usbutils package). But after a few seconds, the device
dissappears from lsusb!! However, it is always to be found in
/proc/bus/usb/devices.
Any clue as to why this behavior? This camera works with SuSe (I think
10.someversion), but it should work on Debian too!!
Thanks for all your help,
Sayantan.
=============================
Debug information:
1. lsusb -v # For the very short period of time the camera is
reported by lsusb
Bus 001 Device 009: ID 04a9:310e Canon, Inc.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x04a9 Canon, Inc.
idProduct 0x310e
bcdDevice 0.02
iManufacturer 1
iProduct 2
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 39
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xc0
Self Powered
MaxPower 2mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 6 Imaging
bInterfaceSubClass 1 Still Image Capture
bInterfaceProtocol 1 Picture Transfer Protocol (PIMA 15470)
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 32
can't get device qualifier: Operation not permitted
can't get debug descriptor: Operation not permitted
2. cat /proc/bus/usb/devices # Device info for the camera
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 10 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=04a9 ProdID=310e Rev= 0.02
S: Manufacturer=Canon Inc.
S: Product=Canon Digital Camera
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 2mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=06(still) Sub=01 Prot=01 Driver=(none)
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
3. tail -f /var/log/messages # When camera is inserted and turned on
Oct 3 21:50:39 localhost kernel: usb 1-1: new full speed USB device
using uhci_hcd and address 10
Oct 3 21:50:40 localhost usb.agent[7405]: libgphoto2: loaded successfully
--
http://www.cse.ohio-state.edu/~surs
Reply to: