[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

usb flash stick on 2.6.8.1 kernel



Hi all,
Below are the outputs of dmesg & lsmod output./

Linux version 2.6.8.1 (root@shiva1) (gcc version 3.3.4 (Debian 1:3.3.4-13)) #1 Mon Dec 20 14:34:05 IST 2004
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 0000000000080000 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000003ffec000 (usable)
 BIOS-e820: 000000003ffec000 - 000000003ffef000 (ACPI data)
 BIOS-e820: 000000003ffef000 - 000000003ffff000 (reserved)
 BIOS-e820: 000000003ffff000 - 0000000040000000 (ACPI NVS)
 BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
Warning only 896MB will be used.
Use a HIGHMEM enabled kernel.
896MB LOWMEM available.
On node 0 totalpages: 229376
  DMA zone: 4096 pages, LIFO batch:1
  Normal zone: 225280 pages, LIFO batch:16
  HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 ASUS                                      ) @ 0x000f8070
ACPI: RSDT (v001 ASUS   A7N266VM 0x42302e31 MSFT 0x31313031) @ 0x3ffec000
ACPI: FADT (v001 ASUS   A7N266VM 0x42302e31 MSFT 0x31313031) @ 0x3ffec100
ACPI: BOOT (v001 ASUS   A7N266VM 0x42302e31 MSFT 0x31313031) @ 0x3ffec040
ACPI: MADT (v001 ASUS   A7N266VM 0x42302e31 MSFT 0x31313031) @ 0x3ffec080
ACPI: DSDT (v001   ASUS A7N266VM 0x00001000 MSFT 0x0100000b) @ 0x00000000
Built 1 zonelists
Kernel command line: BOOT_IMAGE=sarge-2.6.8.1 ro root=301
Initializing CPU#0
PID hash table entries: 4096 (order 12: 32768 bytes)
Detected 2004.571 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 904972k/917504k available (2226k kernel code, 11660k reserved, 957k data, 140k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 3964.92 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000
CPU: After vendor identify, caps:  0383fbff c1c3fbff 00000000 00000000
CPU: CLK_CTL MSR was 60031223. Reprogramming to 20031223
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps:        0383fbff c1c3fbff 00000000 00000020
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD Athlon(TM) XP 2400+ stepping 01
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xf1b20, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
SCSI subsystem initialized
Linux Kernel Card Services
  options:  [pci] [pm]
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router default [10de/01b2] at 0000:00:01.0
Simple Boot Flag at 0x3f set to 0x1
IA-32 Microcode Update Driver: v1.14 <tigran@veritas.com>
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Linux agpgart interface v0.100 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
loop: loaded (max 8 devices)
eepro100.c:v1.09j-t 9/29/99 Donald Becker http://www.scyld.com/network/eepro100.html
eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <saw@saw.sw.com.sg> and others
eth0: 0000:01:08.0, 00:00:4B:50:05:11, IRQ 5.
  Receiver lock-up bug exists -- enabling work-around.
  Board assembly 373132-051, Physical connectors present: RJ45
  Primary interface chip i82555 PHY #1.
    Secondary interface chip i82503.
  General self-test: passed.
  Serial sub-system self-test: passed.
  Internal registers self-test: passed.
  ROM checksum self-test: passed (0x24c9f043).
  Receiver lock-up workaround activated.
Linux video capture interface: v1.00
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE: IDE controller at PCI slot 0000:00:09.0
NFORCE: chipset revision 195
NFORCE: not 100% native mode: will probe irqs later
NFORCE: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE: 0000:00:09.0 (rev c3) UDMA100 controller
    ide0: BM-DMA at 0xa800-0xa807, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xa808-0xa80f, BIOS settings: hdc:pio, hdd:DMA
hda: SAMSUNG SP0802N, ATA DISK drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdd: GCR-8523B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 1024KiB
hda: 156368016 sectors (80060 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
 hda: hda1 hda2 < hda5 hda6 hda7 hda8 > hda3 hda4
hdd: ATAPI 52X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.20
st: Version 20040403, fixed bufsize 32768, s/g segs 256
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
input: PS/2 Logitech Mouse on isa0060/serio1
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
md: raid1 personality registered as nr 3
md: multipath personality registered as nr 7
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 1
NET: Registered protocol family 17
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 140k freed
Adding 586332k swap on /dev/hda5.  Priority:-1 extents:1
usbcore: registered new driver usbkbd
drivers/usb/input/usbkbd.c: :USB HID Boot Protocol keyboard driver
Initializing USB Mass Storage driver...
kobject_register failed for usb-storage (-17)
 [<c01f7a87>] kobject_register+0x57/0x60
 [<c024ace0>] bus_add_driver+0x50/0xb0
 [<c024b2df>] driver_register+0x2f/0x40
 [<c0114520>] printk+0x100/0x140
 [<c02a09af>] usb_register+0x3f/0xa0
 [<f886501f>] usb_stor_init+0x1f/0x3b [usb_storage]
 [<c01287e7>] sys_init_module+0x107/0x1d0
 [<c0103e8b>] syscall_call+0x7/0xb
usbcore: error -17 registering driver usb-storage
PCI: Enabling device 0000:00:06.0 (0005 -> 0007)
PCI: Setting latency timer of device 0000:00:06.0 to 64
intel8x0_measure_ac97_clock: measured 49454 usecs
intel8x0: clocking to 47476
agpgart: Detected NVIDIA nForce chipset
agpgart: Maximum main memory to use for agp memory: 816M
agpgart: AGP aperture is 64M @ 0xf8000000
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
PCI: IRQ 6 for device 0000:00:02.0 doesn't match PIRQ mask - try pci=usepirqmask
ohci_hcd 0000:00:02.0: nVidia Corporation nForce USB Controller
ohci_hcd 0000:00:02.0: USB HC TakeOver from BIOS/SMM
ohci_hcd 0000:00:02.0: reset, control = 0x680
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: irq 6, pci mem f887b000
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:02.0: supports USB remote wakeup
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: default language 0x0409
usb usb1: Product: nVidia Corporation nForce USB Controller
usb usb1: Manufacturer: Linux 2.6.8.1 ohci_hcd
usb usb1: SerialNumber: 0000:00:02.0
usb usb1: hotplug
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: hotplug
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: global over-current protection
hub 1-0:1.0: power on to power good time: 2ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: no over-current condition exists
ohci_hcd 0000:00:02.0: created debug files
ohci_hcd 0000:00:02.0: OHCI controller state
ohci_hcd 0000:00:02.0: OHCI 1.0, with legacy support registers
ohci_hcd 0000:00:02.0: control 0x683 RWE RWC HCFS=operational CBSR=3
ohci_hcd 0000:00:02.0: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:02.0: intrstatus 0x00000004 SF
ohci_hcd 0000:00:02.0: intrenable 0x8000000a MIE RD WDH
ohci_hcd 0000:00:02.0: hcca frame #002e
ohci_hcd 0000:00:02.0: roothub.a 01000203 POTPGT=1 NPS NDP=3
ohci_hcd 0000:00:02.0: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:02.0: roothub.status 00000000
ohci_hcd 0000:00:02.0: roothub.portstatus [0] 0x00000100 PPS
ohci_hcd 0000:00:02.0: roothub.portstatus [1] 0x00000100 PPS
ohci_hcd 0000:00:02.0: roothub.portstatus [2] 0x00000100 PPS
PCI: IRQ 6 for device 0000:00:03.0 doesn't match PIRQ mask - try pci=usepirqmask
ohci_hcd 0000:00:03.0: nVidia Corporation nForce USB Controller (#2)
ohci_hcd 0000:00:03.0: reset, control = 0x600
PCI: Setting latency timer of device 0000:00:03.0 to 64
ohci_hcd 0000:00:03.0: irq 6, pci mem f888c000
ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:03.0: supports USB remote wakeup
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: default language 0x0409
usb usb2: Product: nVidia Corporation nForce USB Controller (#2)
usb usb2: Manufacturer: Linux 2.6.8.1 ohci_hcd
usb usb2: SerialNumber: 0000:00:03.0
usb usb2: hotplug
usb usb2: adding 2-0:1.0 (config #1, interface 0)
usb 2-0:1.0: hotplug
ohci_hcd 0000:00:02.0: suspend root hub
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: global over-current protection
hub 2-0:1.0: power on to power good time: 2ms
hub 2-0:1.0: local power source is good
hub 2-0:1.0: no over-current condition exists
ohci_hcd 0000:00:03.0: created debug files
ohci_hcd 0000:00:03.0: OHCI controller state
ohci_hcd 0000:00:03.0: OHCI 1.0, with legacy support registers
ohci_hcd 0000:00:03.0: control 0x683 RWE RWC HCFS=operational CBSR=3
ohci_hcd 0000:00:03.0: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:03.0: intrstatus 0x00000004 SF
ohci_hcd 0000:00:03.0: intrenable 0x8000000a MIE RD WDH
ohci_hcd 0000:00:03.0: hcca frame #00a6
ohci_hcd 0000:00:03.0: roothub.a 01000203 POTPGT=1 NPS NDP=3
ohci_hcd 0000:00:03.0: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:03.0: roothub.status 00000000
ohci_hcd 0000:00:03.0: roothub.portstatus [0] 0x00000100 PPS
ohci_hcd 0000:00:03.0: roothub.portstatus [1] 0x00000100 PPS
ohci_hcd 0000:00:03.0: roothub.portstatus [2] 0x00000100 PPS
ohci_hcd 0000:00:03.0: suspend root hub
Initializing USB Mass Storage driver...
kobject_register failed for usb-storage (-17)
 [<c01f7a87>] kobject_register+0x57/0x60
 [<c024ace0>] bus_add_driver+0x50/0xb0
 [<c024b2df>] driver_register+0x2f/0x40
 [<c0114520>] printk+0x100/0x140
 [<c02a09af>] usb_register+0x3f/0xa0
 [<f886f01f>] usb_stor_init+0x1f/0x3b [usb_storage]
 [<c01287e7>] sys_init_module+0x107/0x1d0
 [<c0103e8b>] syscall_call+0x7/0xb
usbcore: error -17 registering driver usb-storage
ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [1] = 0x00010101 CSC PPS CCS
hub 1-0:1.0: port 2, status 0101, change 0001, 12 Mb/s
hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x101
ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [1] = 0x00100103 PRSC PPS PES CCS
usb 1-2: new full speed USB device using address 2
usb 1-2: control timeout on ep0out
ohci_hcd 0000:00:02.0: Unlink after no-IRQ?  Different ACPI or APIC settings may help.

The above is the dmesg output.
 
 

Module                  Size  Used by
ohci_hcd               33860  0
nvidia_agp              7836  1
snd_intel8x0           34632  0
snd_ac97_codec         68868  1 snd_intel8x0
snd_pcm_oss            53800  0
snd_mixer_oss          19712  1 snd_pcm_oss
snd_pcm                94728  2 snd_intel8x0,snd_pcm_oss
snd_timer              24452  1 snd_pcm
snd_page_alloc         11720  2 snd_intel8x0,snd_pcm
snd_mpu401_uart         7616  1 snd_intel8x0
snd_rawmidi            23972  1 snd_mpu401_uart
snd                    53476  8 snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer,snd_mpu401_uart,snd_rawmidi
usbkbd                  7424  0

the lsmod output is above
 

Whenever i insert a usb flash stick it doesnt mount it on any scsi drive ..
and i have problem with usb-storage module..
should anything module of scsi be enabled or any suggestions pls...
 

lspci output
 Host bridge: nVidia Corporation nForce CPU bridge (rev b2)
0000:00:00.1 RAM memory: nVidia Corporation nForce 220/420 Memory Controller (rev b2)
0000:00:00.2 RAM memory: nVidia Corporation nForce 220/420 Memory Controller (rev b2)
0000:00:00.3 RAM memory: nVidia Corporation: Unknown device 01aa (rev b2)
0000:00:01.0 ISA bridge: nVidia Corporation nForce ISA Bridge (rev c3)
0000:00:01.1 SMBus: nVidia Corporation nForce PCI System Management (rev c1)
0000:00:02.0 USB Controller: nVidia Corporation nForce USB Controller (rev c3)
0000:00:03.0 USB Controller: nVidia Corporation nForce USB Controller (rev c3)
0000:00:05.0 Multimedia audio controller: nVidia Corporation: Unknown device 01b0 (rev c2)
0000:00:06.0 Multimedia audio controller: nVidia Corporation nForce Audio (rev c2)
0000:00:08.0 PCI bridge: nVidia Corporation nForce PCI-to-PCI bridge (rev c2)
0000:00:09.0 IDE interface: nVidia Corporation nForce IDE (rev c3)
0000:00:1e.0 PCI bridge: nVidia Corporation nForce AGP to PCI Bridge (rev b2)
0000:01:08.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev 05)
0000:02:00.0 VGA compatible controller: nVidia Corporation NV5M64 [RIVA TNT2 Model 64/Model 64 Pro] (rev 15)
 

uname -r 2.6.8.1
 

How to get usb flash stick working on 2.6.8.1 kernel debian sarge

Thanks and regards,
Vijaya
 
 
 
 


Reply to: