slow booting after installing new hdd
Hi all.
a few days ago, I had 82.3GB disk installed on my box
as primary slave.
after that, I turned it on and reading messages of kernel,
and found messages that means 'hdb' recognized smoothly.
that's good.
badly, I found some error messages too,
and noticed booting is very slower than before.
the messages is below.
--------------------------------------------
PIIX4: IDE controller at PCI slot 00:04.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:DMA, hdd:pio
hda: QUANTUM FIREBALL EX12.7A, ATA DISK drive
hdb: HDS722580VLAT20, ATA DISK drive
blk: queue c04102a0, I/O limit 4095Mb (mask 0xffffffff)
blk: queue c04103e8, I/O limit 4095Mb (mask 0xffffffff)
hdc: CD-950E/TKU, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: 24901632 sectors (12750 MB) w/418KiB Cache, CHS=1550/255/63, UDMA(33)
hdb: attached ide-disk driver.
hdb: 160836480 sectors (82348 MB) w/1794KiB Cache, CHS=10011/255/63, UDMA(33)
hdc: attached ide-cdrom driver.
hdc: ATAPI 52X CD-ROM drive, 128kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
Partition check:
hda:<4>hda: dma_timer_expiry: dma status == 0x61
hda: error waiting for DMA
hda: dma timeout retry: status=0x58 { DriveReady SeekComplete DataRequest }
blk: queue c04102a0, I/O limit 4095Mb (mask 0xffffffff)
hda1 hda2 hda3 <<4>hda: dma_timer_expiry: dma status == 0x61
hda: error waiting for DMA
hda: dma timeout retry: status=0x5a { DriveReady SeekComplete DataRequest Index }
hda5<4>hda: dma_timer_expiry: dma status == 0x61
hda: error waiting for DMA
hda: dma timeout retry: status=0x58 { DriveReady SeekComplete DataRequest }
hda6<4>hda: dma_timer_expiry: dma status == 0x61
hda: error waiting for DMA
hda: dma timeout retry: status=0x58 { DriveReady SeekComplete DataRequest }
hda7 hda8 hda9 hda10 hda11 >
hdb: hdb1 < hdb5 >
SCSI subsystem driver Revision: 1.00
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
Soundblaster audio driver Copyright (C) by Hannu Savolainen 1993-1996
sb: No ISAPnP cards found, trying standard ones...
sb: I/O, IRQ, and DMA are mandatory
YM3812 and OPL-3 driver Copyright (C) by Hannu Savolainen, Rob Hooft 1993-1996
es1371: version v0.32 time 12:00:53 Nov 28 2003
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
usb.c: registered new driver hub
host/uhci.c: USB Universal Host Controller Interface driver v1.1
PCI: Found IRQ 9 for device 00:04.2
PCI: Sharing IRQ 9 with 00:09.0
--------------------------------------------
what's wrong?
hardware problem?
mobo : P2B with newest bios with which it solved large disk problem
hdd : HITACHI deskstar
kernel : 2.4.22
(I can mount and use the disk normally.)
Thanks in advance.
Reply to: