Help with sound card

Hello everyone. My soundcard is a soundblaster CT3600. I can't get it to work.

I am getting the following error when I try to load modules to use it as follows:

spoke:/proc# modprobe sb io=0x220 irq=10 dma=1 dma16=5 mpu_io=0x330

Soundblaster audio driver Copyright (C) by Hannu Savolainen 1993-1996

SB 4.13 detected OK (220)

sb: Interrupt test on IRQ10 failed - Probable IRQ conflict

It does the exact same thing when I use different unused irq's.

Do these errors have something to do with the fact that there is a ide controller on the card? I haven't seen any evidence of this. How do I get my sound card working?

Thanks,

Mark Y

The /proc info for the above example is as follows:

Script started on Sat Feb 22 03:55:15 2003

spoke:~# cat /proc/interrupts
           CPU0
0:     174178          XT-PIC timer
1:       3495          XT-PIC keyboard
2:          0          XT-PIC cascade
5:          1          XT-PIC eth0
6:         25          XT-PIC floppy
8:          3          XT-PIC rtc
10:          0          XT-PIC soundblaster
11:         51          XT-PIC eth1
12:       3667          XT-PIC PS/2 Mouse
13:          1          XT-PIC fpu
14:     217968          XT-PIC ide0
15:        211          XT-PIC ide1
NMI:          0
spoke:~# cat /proc/dma
1: SoundBlaster8
2: floppy
4: cascade
5: SoundBlaster16
spoke:~# cat /proc/ioports
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0070-007f : rtc
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
0210-021f : 3c509
0220-022f : soundblaster
02f8-02ff : serial(set)
0330-0333 : MPU-401 UART
0376-0376 : ide1
03c0-03df : vga+
03f0-03f5 : floppy
03f6-03f6 : ide0
03f7-03f7 : floppy DIR
03f8-03ff : serial(set)
6100-611f : eth1
9000-9007 : ide0
9008-900f : ide1
spoke:~# exit
exit

Script done on Sat Feb 22 03:55:41 2003

The manufactures info about the card is as follows:

Sound Blaster 32 is a 16-bit ISA audio board. This Plug and Play card comes equiped with an IDE CD-ROM interface and an EMU8000 AWE Synthesizer chip. It provides options to upgrade with a SIMM RAM upgrade module

General

FM Synthesis: Yes

Wave Synthesis: Yes

Built-In Stereo Power Amplifier: Yes

Built-In Digital/Analog Mixer: Yes

Plug and Play: Yes

CD-ROM Interface: IDE

Hardware Settings
Note: all settings are software selectable via Plug and Play.

Interrupt (IRQ): 2, 5, 7, 10
8-bit DMA Channel: 0, 1, 3
16-bit DMA Channel: 5, 6, 7
Joystick I/O Address: 200 Hex
Audio I/O Address: 220, 240, 260, 280 Hex
MPU-401 I/O Address: 300, 330 Hex
FM Synthesizer I/O Address: 388 Hex
Wave Synthesizer I/O Address: 6x0, Ax0, Ex0 Hex
IDE Interface Port: Secondary, Tertiary, Quaternary
IDE Interface IRQ: 10, 11, 12, 15
MPU-401 Port

[Enabled] (MFBEN closed)

[Disabled] (MFBEN open)

Connectors

Line-In: Yes
Mic-In: Yes
Line-Out: Yes
Speaker-Out: Yes
PC Speaker-In: Yes
SPDIF: Yes
Game/Joystick Port: Yes
CD-ROM Audio-In (SB Audio Socket): Yes
CD-ROM Audio-In (MPC2 Socket): Yes
30-pin SIMM RAM Upgrade Module: Yes
CSP Chip Socket: No
Wave Blaster Daughter Board Connector: No
External CD-ROM: Not Applicable
Modem Feature Connector: Yes

Help with sound card - sb ct3600