Re: cdrecord problems
try running xcdroast and seeing if you can get that setup and working first.
----- Original Message -----
From: "Patrik Modesto" <mody@quick.cz>
To: <debian-user@lists.debian.org>
Sent: Tuesday, December 18, 2001 1:29 PM
Subject: cdrecord problems
> Hi,
> I'm out of ideas, so I need Your help. I'm trying to write some files to
> CD-RW, but without success. :-( I'm using Debian Woody (daily updated),
> with custom kernel 2.4.16 (enabled scsi emulation, reiserfs, ext3). I
> tried everything I found in CD-Writing howto, but still no good. Only
> few Kb gets on CD. Dummy mode is off. Funny is, that I can do fast-erase
> of CD-RW disk. Full-erase freezes whole Gnome. :-(
> Can someone help?
>
> Thanks
>
> Patrik
>
> Here is some info:
>
> cdrecord -scanbus:
> -----------------
> Cdrecord 1.10 (i686-pc-linux-gnu) Copyright (C) 1995-2001 Jörg Schilling
> Linux sg driver version: 3.1.20
> Using libscg version 'schily-0.5'
> scsibus0:
> 0,0,0 0) 'IOMEGA ' 'ZIP 100 ' '14.A' Removable
> Disk
> 0,1,0 1) 'PLEXTOR ' 'CD-R PX-W1610A' '1.04'
> Removable CD-ROM
> 0,2,0 2) *
> 0,3,0 3) *
> 0,4,0 4) *
> 0,5,0 5) *
> 0,6,0 6) *
> 0,7,0 7) *
>
>
> gcombust - cdrecord output:
> --------------------------
> Cdrecord 1.10 (i686-pc-linux-gnu) Copyright (C) 1995-2001 Jörg Schilling
> TOC Type: 1 = CD-ROM
> Using libscg version 'schily-0.5'
> Driveropts: 'burnproof'
> atapi: 1
> Device type : Removable CD-ROM
> Version : 0
> Response Format: 1
> Vendor_info : 'PLEXTOR '
> Identifikation : 'CD-R PX-W1610A'
> Revision : '1.04'
> Device seems to be: Generic mmc CD-RW.
> Using generic SCSI-3/mmc CD-R driver (mmc_cdr).
> Driver flags : SWABAUDIO
> Drive buf size : 1190112 = 1162 KB
> FIFO size : 4194304 = 4096 KB
> Track 01: data 126 MB padsize: 30 KB
> Lout start: 145 MB (14:25/12) = 64737 sectors
> Current Secsize: 2048
> ATIP info from disk:
> Indicated writing power: 6
> Reference speed: 0
> Is not unrestricted
> Is erasable
> ATIP start of lead in: -11078 (97:34/22)
> ATIP start of lead out: 359849 (79:59/74)
> speed low: 0 speed high: 4
> power mult factor: 3 5
> recommended erase/write power: 3
> A2 values: 5C C6 26
> Disk type: Phase change
> Manuf. index: 11
> Manufacturer: Mitsubishi Chemical Corporation
> Blocks total: 359849 Blocks current: 359849 Blocks
> remaining: 295112
> Starting to write CD/DVD at speed 4 in write mode
> for single session.
> scsidev: '0,1,0'
> scsibus: 0 target: 1 lun: 0
> Linux sg driver version: 3.1.20iCdrecord 1.10
> (i686-pc-linux-gnu) Copyright (C) 1995-2001 Jörg
> Schilling
> TOC Type: 1 = CD-ROM
> Using libscg version 'schily-0.5'
> Driveropts: 'burnproof'
> atapi: 1
> Device type : Removable CD-ROM
> Version : 0
> Response Format: 1
> Vendor_info : 'PLEXTOR '
> Identifikation : 'CD-R PX-W1610A'
> Revision : '1.04'
> Device seems to be: Generic mmc CD-RW.
> Using generic SCSI-3/mmc CD-R driver (mmc_cdr).
> Driver flags : SWABAUDIO
> Drive buf size : 1190112 = 1162 KB
> FIFO size : 4194304 = 4096 KB
> Track 01: data 126 MB padsize: 30 KB
> Lout start: 145 MB (14:25/12) = 64737 sectors
> Current Secsize: 2048
> ATIP info from disk:
> Indicated writing power: 6
> Reference speed: 0
> Is not unrestricted
> Is erasable
> ATIP start of lead in: -11078 (97:34/22)
> ATIP start of lead out: 359849
> (79:59/74)
> speed low: 0 speed high: 4
> power mult factor: 3 5
> recommended erase/write power: 3
> A2 values: 5C C6 26
> Disk type: Phase change
> Manuf. index: 11
> Manufacturer: Mitsubishi
> Chemical Corporation
> Blocks total: 359849 Blocks
> current: 359849 Blocks
> remaining: 295112
> Starting to write CD/DVD at
> speed 4 in write mode for single
> session.
> scsidev: '0,1,0'
> scsibus: 0 target: 1 lun: 0
> Linux sg driver version: 3.1.20
> Performing OPC...
> /usr/bin/cdrecord: Turning
> BURN-Proof on
>
> /usr/bin/cdrecord: Input/output
> error. write_g1: scsi sendcmd:
> retryable error
> CDB: 2A 00 00 00 00 1F 00 00 1F
> 00
> status: 0x0 (GOOD STATUS)
> cmd finished after 0.933s
> timeout 40s
> Track 01: 0 of 126 MB written.
> write track data: error after
> 63488 bytes
> Trouble flushing the cache
> Writing time: 11.943s
> Sense Bytes: 70 00 00 00 00 00
> 00 0A 00 00 00 00 00 00 00 00 00
> 00
> /usr/bin/cdrecord: Input/output
> error. flush cache: scsi
> sendcmd: no error
> CDB: 35 00 00 00 00 00 00 00 00
> 00
> status: 0x2 (CHECK CONDITION)
> Sense Bytes: 70 00 06 00 00 00
> 00 0A 00 00 00 00 29 00 00 00
> Sense Key: 0x6 Unit Attention,
> Segment 0
> Sense Code: 0x29 Qual 0x00
> (power on, reset, or bus device
> reset occurred) Fru 0x0
> Sense flags: Blk 0 (not valid)
> cmd finished after 0.000s
> timeout 120s
> /usr/bin/cdrecord: fifo had 65
> puts and 2 gets.
> /usr/bin/cdrecord: fifo was 0
> times empty and 1 times full,
> min fill was 98%.
>
> /var/log/messages:
> -----------------
> Dec 18 19:18:16 mody kernel: hdd: status error: status=0x58 { DriveReady
> SeekComplete DataRequest }
> Dec 18 19:18:16 mody kernel: hdd: drive not ready for command
> Dec 18 19:18:16 mody kernel: hdd: status error: status=0x58 { DriveReady
> SeekComplete DataRequest }
> Dec 18 19:18:16 mody kernel: hdd: drive not ready for command
> Dec 18 19:18:16 mody kernel: hdd: status error: status=0x58 { DriveReady
> SeekComplete DataRequest }
> Dec 18 19:18:16 mody kernel: hdd: drive not ready for command
> Dec 18 19:18:16 mody kernel: hdd: status error: status=0x58 { DriveReady
> SeekComplete DataRequest }
> Dec 18 19:18:16 mody kernel: hdd: DMA disabled
> Dec 18 19:18:16 mody kernel: hdd: drive not ready for command
> Dec 18 19:18:16 mody kernel: hdd: ATAPI reset complete
> Dec 18 19:18:16 mody kernel: hdd: status error: status=0x49 { DriveReady
> DataRequest Error }
> Dec 18 19:18:16 mody kernel: hdd: status error: error=0x04
> Dec 18 19:18:16 mody kernel: hdd: drive not ready for command
> Dec 18 19:18:16 mody kernel: hdd: status error: status=0x58 { DriveReady
> SeekComplete DataRequest }
> Dec 18 19:18:16 mody kernel: hdd: drive not ready for command
> Dec 18 19:18:16 mody kernel: hdd: status error: status=0x58 { DriveReady
> SeekComplete DataRequest }
> Dec 18 19:18:16 mody kernel: hdd: drive not ready for command
> Dec 18 19:18:16 mody kernel: hdd: status error: status=0x58 { DriveReady
> SeekComplete DataRequest }
> Dec 18 19:18:16 mody kernel: hdd: drive not ready for command
> Dec 18 19:18:17 mody kernel: hdd: ATAPI reset complete
> Dec 18 19:18:17 mody kernel: hdd: status error: status=0x49 { DriveReady
> DataRequest Error }
> Dec 18 19:18:17 mody kernel: hdd: status error: error=0x04
> Dec 18 19:18:17 mody kernel: hdd: drive not ready for command
> Dec 18 19:18:22 mody kernel: hdd: status error: status=0x58 { DriveReady
> SeekComplete DataRequest }
> Dec 18 19:18:22 mody kernel: hdd: drive not ready for command
>
>
> --
> To UNSUBSCRIBE, email to debian-user-request@lists.debian.org
> with a subject of "unsubscribe". Trouble? Contact
listmaster@lists.debian.org
>
>
Reply to: