cdrecord problems
Hi,
I'm out of ideas, so I need Your help. I'm trying to write some files to
CD-RW, but without success. :-( I'm using Debian Woody (daily updated),
with custom kernel 2.4.16 (enabled scsi emulation, reiserfs, ext3). I
tried everything I found in CD-Writing howto, but still no good. Only
few Kb gets on CD. Dummy mode is off. Funny is, that I can do fast-erase
of CD-RW disk. Full-erase freezes whole Gnome. :-(
Can someone help?
Thanks
Patrik
Here is some info:
cdrecord -scanbus:
-----------------
Cdrecord 1.10 (i686-pc-linux-gnu) Copyright (C) 1995-2001 Jörg Schilling
Linux sg driver version: 3.1.20
Using libscg version 'schily-0.5'
scsibus0:
0,0,0 0) 'IOMEGA ' 'ZIP 100 ' '14.A' Removable
Disk
0,1,0 1) 'PLEXTOR ' 'CD-R PX-W1610A' '1.04'
Removable CD-ROM
0,2,0 2) *
0,3,0 3) *
0,4,0 4) *
0,5,0 5) *
0,6,0 6) *
0,7,0 7) *
gcombust - cdrecord output:
--------------------------
Cdrecord 1.10 (i686-pc-linux-gnu) Copyright (C) 1995-2001 Jörg Schilling
TOC Type: 1 = CD-ROM
Using libscg version 'schily-0.5'
Driveropts: 'burnproof'
atapi: 1
Device type : Removable CD-ROM
Version : 0
Response Format: 1
Vendor_info : 'PLEXTOR '
Identifikation : 'CD-R PX-W1610A'
Revision : '1.04'
Device seems to be: Generic mmc CD-RW.
Using generic SCSI-3/mmc CD-R driver (mmc_cdr).
Driver flags : SWABAUDIO
Drive buf size : 1190112 = 1162 KB
FIFO size : 4194304 = 4096 KB
Track 01: data 126 MB padsize: 30 KB
Lout start: 145 MB (14:25/12) = 64737 sectors
Current Secsize: 2048
ATIP info from disk:
Indicated writing power: 6
Reference speed: 0
Is not unrestricted
Is erasable
ATIP start of lead in: -11078 (97:34/22)
ATIP start of lead out: 359849 (79:59/74)
speed low: 0 speed high: 4
power mult factor: 3 5
recommended erase/write power: 3
A2 values: 5C C6 26
Disk type: Phase change
Manuf. index: 11
Manufacturer: Mitsubishi Chemical Corporation
Blocks total: 359849 Blocks current: 359849 Blocks
remaining: 295112
Starting to write CD/DVD at speed 4 in write mode
for single session.
scsidev: '0,1,0'
scsibus: 0 target: 1 lun: 0
Linux sg driver version: 3.1.20iCdrecord 1.10
(i686-pc-linux-gnu) Copyright (C) 1995-2001 Jörg
Schilling
TOC Type: 1 = CD-ROM
Using libscg version 'schily-0.5'
Driveropts: 'burnproof'
atapi: 1
Device type : Removable CD-ROM
Version : 0
Response Format: 1
Vendor_info : 'PLEXTOR '
Identifikation : 'CD-R PX-W1610A'
Revision : '1.04'
Device seems to be: Generic mmc CD-RW.
Using generic SCSI-3/mmc CD-R driver (mmc_cdr).
Driver flags : SWABAUDIO
Drive buf size : 1190112 = 1162 KB
FIFO size : 4194304 = 4096 KB
Track 01: data 126 MB padsize: 30 KB
Lout start: 145 MB (14:25/12) = 64737 sectors
Current Secsize: 2048
ATIP info from disk:
Indicated writing power: 6
Reference speed: 0
Is not unrestricted
Is erasable
ATIP start of lead in: -11078 (97:34/22)
ATIP start of lead out: 359849
(79:59/74)
speed low: 0 speed high: 4
power mult factor: 3 5
recommended erase/write power: 3
A2 values: 5C C6 26
Disk type: Phase change
Manuf. index: 11
Manufacturer: Mitsubishi
Chemical Corporation
Blocks total: 359849 Blocks
current: 359849 Blocks
remaining: 295112
Starting to write CD/DVD at
speed 4 in write mode for single
session.
scsidev: '0,1,0'
scsibus: 0 target: 1 lun: 0
Linux sg driver version: 3.1.20
Performing OPC...
/usr/bin/cdrecord: Turning
BURN-Proof on
/usr/bin/cdrecord: Input/output
error. write_g1: scsi sendcmd:
retryable error
CDB: 2A 00 00 00 00 1F 00 00 1F
00
status: 0x0 (GOOD STATUS)
cmd finished after 0.933s
timeout 40s
Track 01: 0 of 126 MB written.
write track data: error after
63488 bytes
Trouble flushing the cache
Writing time: 11.943s
Sense Bytes: 70 00 00 00 00 00
00 0A 00 00 00 00 00 00 00 00 00
00
/usr/bin/cdrecord: Input/output
error. flush cache: scsi
sendcmd: no error
CDB: 35 00 00 00 00 00 00 00 00
00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 06 00 00 00
00 0A 00 00 00 00 29 00 00 00
Sense Key: 0x6 Unit Attention,
Segment 0
Sense Code: 0x29 Qual 0x00
(power on, reset, or bus device
reset occurred) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.000s
timeout 120s
/usr/bin/cdrecord: fifo had 65
puts and 2 gets.
/usr/bin/cdrecord: fifo was 0
times empty and 1 times full,
min fill was 98%.
/var/log/messages:
-----------------
Dec 18 19:18:16 mody kernel: hdd: status error: status=0x58 { DriveReady
SeekComplete DataRequest }
Dec 18 19:18:16 mody kernel: hdd: drive not ready for command
Dec 18 19:18:16 mody kernel: hdd: status error: status=0x58 { DriveReady
SeekComplete DataRequest }
Dec 18 19:18:16 mody kernel: hdd: drive not ready for command
Dec 18 19:18:16 mody kernel: hdd: status error: status=0x58 { DriveReady
SeekComplete DataRequest }
Dec 18 19:18:16 mody kernel: hdd: drive not ready for command
Dec 18 19:18:16 mody kernel: hdd: status error: status=0x58 { DriveReady
SeekComplete DataRequest }
Dec 18 19:18:16 mody kernel: hdd: DMA disabled
Dec 18 19:18:16 mody kernel: hdd: drive not ready for command
Dec 18 19:18:16 mody kernel: hdd: ATAPI reset complete
Dec 18 19:18:16 mody kernel: hdd: status error: status=0x49 { DriveReady
DataRequest Error }
Dec 18 19:18:16 mody kernel: hdd: status error: error=0x04
Dec 18 19:18:16 mody kernel: hdd: drive not ready for command
Dec 18 19:18:16 mody kernel: hdd: status error: status=0x58 { DriveReady
SeekComplete DataRequest }
Dec 18 19:18:16 mody kernel: hdd: drive not ready for command
Dec 18 19:18:16 mody kernel: hdd: status error: status=0x58 { DriveReady
SeekComplete DataRequest }
Dec 18 19:18:16 mody kernel: hdd: drive not ready for command
Dec 18 19:18:16 mody kernel: hdd: status error: status=0x58 { DriveReady
SeekComplete DataRequest }
Dec 18 19:18:16 mody kernel: hdd: drive not ready for command
Dec 18 19:18:17 mody kernel: hdd: ATAPI reset complete
Dec 18 19:18:17 mody kernel: hdd: status error: status=0x49 { DriveReady
DataRequest Error }
Dec 18 19:18:17 mody kernel: hdd: status error: error=0x04
Dec 18 19:18:17 mody kernel: hdd: drive not ready for command
Dec 18 19:18:22 mody kernel: hdd: status error: status=0x58 { DriveReady
SeekComplete DataRequest }
Dec 18 19:18:22 mody kernel: hdd: drive not ready for command
Reply to: