pump doesn't get ip
Hi List!
I have a problem configuring my debian potato to use dhcp. I'm
connected to the Internet via cable modem. The network card is
configured to irq=10 and io=0x300. The module is smc-ultra. The card
should be ok.
When I start 'pump', it tries to get dynamic ip from server using
dhcp, but fails everytime. When 'pump' is trying to get the ip,
'ifconfig' shows this:
eth0 Link encap:Ethernet HWaddr 00:00:C0:57:6D:DE
UP BROADCAST RUNNING MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:2 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
Interrupt:10 Base address:0x310 Memory:cc000-d0000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:3924 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
In the output ip address is not defined and the Base address is 0x310,
though
the card is using base address 0x300.
/var/log/syslog shows following messages:
Dec 4 22:43:31 debian pumpd[431]: PUMP: sending discover
Dec 4 22:43:31 debian pumpd[431]: breq: opcode: 1
Dec 4 22:43:31 debian pumpd[431]: breq: hw: 1
Dec 4 22:43:31 debian pumpd[431]: breq: hwlength: 6
Dec 4 22:43:31 debian pumpd[431]: breq: hopcount: 0
Dec 4 22:43:31 debian pumpd[431]: breq: id: 0x6d13df9e
Dec 4 22:43:31 debian pumpd[431]: breq: secs: 0
Dec 4 22:43:31 debian pumpd[431]: breq: flags: 0x 0
Dec 4 22:43:31 debian pumpd[431]: breq: ciaddr: 0.0.0.0
Dec 4 22:43:31 debian pumpd[431]: breq: yiaddr: 0.0.0.0
Dec 4 22:43:31 debian pumpd[431]: breq: server_ip: 0.0.0.0
Dec 4 22:43:31 debian pumpd[431]: breq: bootp_gw_ip: 0.0.0.0
Dec 4 22:43:31 debian pumpd[431]: breq: hwaddr:
Dec 4 22:43:31 debian pumpd[431]: breq: servername:
Dec 4 22:43:31 debian pumpd[431]: breq: bootfile:
Dec 4 22:43:31 debian pumpd[431]: breq: vendor: 0x63 0x53 0x82 0x63
Dec 4 22:43:31 debian pumpd[431]: breq: vendor: 53 1 0x 1
Dec 4 22:43:31 debian pumpd[431]: breq: vendor: 0xff
Dec 4 22:43:41 debian kernel: eth0: Tx timed out, lost interrupt?
TSR=0x3, ISR=0x3, t=999.
Does anyone have any ideas what's wrong. I used 'dhcpcd' in my former
debian, and I have tried it in this new installation but without
success.
Thanks!
Esko
Reply to: