Re: IDE CD-R drive via ide-scsi
David Blackman <david@whizziwig.com> writes:
> Okay, listen here's the deal: you need to take OUT ide-cd support
Done.
> leave in scsi-emulation, scsi-generic, scsi-cdrom......
> now ./MAKDEV sg
Done. I now have /dev/sg[0-16].
> I'm pretty sure that the /dev/scd* come pre-made
> the important thing is to see if you get messages like this on bootup:
> scsi0 : AdvanSys SCSI 3.1E: PCI 20 CDB: IO E400/F, IRQ 9
> scsi1 : SCSI host adapter emulation for IDE ATAPI devices
> scsi : 2 hosts.
> Vendor: HP Model: C5110A Rev: 3638
> Type: Processor ANSI SCSI revision: 02
> Detected scsi generic sga at scsi0, channel 0, id 1, lun 0
> Vendor: IOMEGA Model: ZIP 100 Rev: 13.A
> Type: Direct-Access ANSI SCSI revision: 00
> Detected scsi removable disk sda at scsi1, channel 0, id 0, lun 0
> Vendor: E-IDE Model: CD-ROM 45X/A Rev: 30
> Type: CD-ROM ANSI SCSI revision: 02
> Detected scsi CD-ROM sr0 at scsi1, channel 0, id 1, lun 0
> Vendor: PHILIPS Model: CDD3610 CD-R/RW Rev: 3.08
> Type: CD-ROM ANSI SCSI revision: 02
> Detected scsi CD-ROM sr1 at scsi1, channel 0, id 2, lun 0
> scsi : detected 2 SCSI cdroms 1 SCSI disk total.
> sr0: scsi3-mmc drive: 0x/20x xa/form2 cdda tray
> Uniform CDROM driver Revision: 2.55
> sr1: scsi3-mmc drive: 6x/6x writer cd/rw xa/form2 cdda tray
> SCSI device sda: hdwr sector= 512 bytes. Sectors= 196608 [96 MB] [0.1 GB]
I don't. Rather, I see:
(scsi0) <Adaptec AHA-294X SCSI host adapter> found at PCI 14/0
(scsi0) Narrow Channel, SCSI ID=7, 16/255 SCBs
(scsi0) Warning - detected auto-termination
(scsi0) Please verify driver detected settings are correct.
(scsi0) If not, then please properly set the device termination
(scsi0) in the Adaptec SCSI BIOS by hitting CTRL-A when prompted
(scsi0) during machine bootup.
(scsi0) Cables present (Int-50 YES, Ext-50 NO)
(scsi0) Downloading sequencer code... 406 instructions downloaded
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.17/3.2.4
<Adaptec AHA-294X SCSI host adapter>
scsi : 1 host.
(scsi0:0:0:0) Synchronous at 10.0 Mbyte/sec, offset 15.
Vendor: SEAGATE Model: ST34371N Rev: 0338
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
(scsi0:0:1:0) Synchronous at 10.0 Mbyte/sec, offset 15.
Vendor: MATSHITA Model: CD-ROM CR-506 Rev: 8S05
Type: CD-ROM ANSI SCSI revision: 02
scsi : detected 1 SCSI disk total.
SCSI device sda: hdwr sector= 512 bytes. Sectors= 8496960 [4148 MB] [4.1 GB]
I guess I need to put something that's currently a module back in the
kernel, maybe ide-scsi? Is it built into your kernel? Would you mind
sending me your kernel .config? And what kernel rev are you running?
Thanks for the reply.
> this means for cdrecord I do dev=1,2,0
morgan
--
VVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVV
>> M o r g a n F l e t c h e r http://www.hahaha.org <<
>> Tibi gratias agimus quod nihil fumas. morgan@hahaha.org <<
Reply to: