[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Troubles with ZIP-100 and LS-120.



Hello list:

I've got a ZIP-100 parallel port dirve and a LS-120 internal unit.

I've installed Slink (kernel 2.0.36) but I couldn't set up the ppa.o
module for the zip during the installation (I'll thank any help on this
matter. The lp.o module was installed with the default parameters).
The problem with the LS unit is the one that urges me to solve because I
haven't got a standard floppy disk drive and I need to make both a boot
and a recue disks.

During start up linux detects the LS and assings it to 'hdb' but I'm
unable to mount it so I can't read or write floppies. By the way, I'll
thank any tip on how to configure the kernel to redirect /dev/fd0 to the
LS unit.

There is more data in the attached file 'kernel.txt'.

Thanx in advance.

___

Even God discusses the details with the devil (anonymous)

Antonio A. Rivas aeypil@teleline.es
STARTEG Project aesypil@hotmail.com
___
begin:          vcard
fn:             Antonio Alfredo Rivas Ojanguren
n:              Rivas Ojanguren;Antonio Alfredo
email;internet: aeypil@teleline.es
note:           Cuaquier mensaje para el proyecto STARTEG utilizar la dirección aesypil@hotmail.com. Any message to STARTEG Project send it to aesypil@hotmail.com
x-mozilla-cpt:  ;-1
x-mozilla-html: FALSE
version:        2.1
end:            vcard


Memory: sized by int13 0e801h
Console: 16 point font, 400 scans
Console: colour VGA+ 80x25, 1 virtual console (max 63)
pcibios_init : BIOS32 Service Directory structure at 0x000faf10
pcibios_init : BIOS32 Service Directory entry at 0xfb390
pcibios_init : PCI BIOS revision 2.10 entry at 0xfb3c0
Probing PCI hardware.
Calibrating delay loop.. ok - 665.19 BogoMIPS
Memory: 127168k/131072k available (1136k kernel code, 384k reserved, 2384k data)
Swansea University Computer Society NET3.035 for Linux 2.0
NET3: Unix domain sockets 0.13 for Linux NET3.035.
Swansea University Computer Society TCP/IP for NET3.034
IP Protocols: IGMP, ICMP, UDP, TCP
VFS: Diskquotas version dquot_5.6.0 initialized
Checking 386/387 coupling... Ok, fpu using exception 16 error reporting.
Checking 'hlt' instruction... Ok.
Linux version 2.0.36 (root@gondor) (gcc version 2.7.2.3) #2 Sun Jan 17 19:38:45 EST 1999
Starting kswapd v 1.4.2.2 
Real Time Clock Driver v1.09
tpqic02: Runtime config, $Revision: 0.4.1.5 $, $Date: 1994/10/29 02:46:13 $
tpqic02: DMA buffers: 20 blocks, at address 0x282800 (0x2826ec)
Ramdisk driver initialized : 16 ramdisks of 4096K size
loop: registered device at major 7
hda: TOSHIBA CD-ROM XM-6302B, ATAPI CDROM drive
hdb: LS-120 VER5 00 UHD Floppy, ATAPI FLOPPY drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
floppy0: no floppy controllers found
md driver 0.36.3 MAX_MD_DEV=4, MAX_REAL=8
(scsi0) <Adaptec AHA-294X Ultra SCSI host adapter> found at PCI 9/0
(scsi0) Wide Channel, SCSI ID=7, 16/255 SCBs
(scsi0) Warning - detected auto-termination
(scsi0) Please verify driver detected settings are correct.
(scsi0) If not, then please properly set the device termination
(scsi0) in the Adaptec SCSI BIOS by hitting CTRL-A when prompted
(scsi0) during machine bootup.
(scsi0) Cables present (Int-50 NO, Int-68 YES, Ext-68 NO)
(scsi0) Downloading sequencer code... 419 instructions downloaded
Failed initialization of WD-7000 SCSI card!
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.4/3.2.4
       <Adaptec AHA-294X Ultra SCSI host adapter>
scsi : 1 host.
  Vendor: SEAGATE   Model: ST34520W          Rev: 1444
  Type:   Direct-Access                      ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
(scsi0:0:0:0) Synchronous at 40.0 Mbyte/sec, offset 8.
scsi : detected 1 SCSI disk total.
SCSI device sda: hdwr sector= 512 bytes. Sectors= 8888924 [4340 MB] [4.3 GB]
Partition check:
 sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 >
hdb: 123264kB, 963/8/32 CHS, 533 kBps, 512 sector size, 720 rpm
hdb: no media in the drive
VFS: Mounted root (ext2 filesystem) readonly.
Adding Swap: 64224k swap-space (priority -1)
Module inserted $Id: cdrom.c,v 0.8 1996/08/10 10:52:11 david Exp $
lp1 at 0x0378, (polling)
PS/2 auxiliary pointing device detected -- driver installed.
Serial driver version 4.13 with no serial options enabled
tty00 at 0x03f8 (irq = 4) is a 16550A
tty01 at 0x02f8 (irq = 3) is a 16550A
tty02 at 0x03e8 (irq = 4) is a 16550A
[MS-DOS FS Rel. 12,FAT 12,check=n,conv=b,uid=0,gid=0,umask=022,bmap]
[me=0xb9,cs=23940,#f=191,fs=5450,fl=61110,ds=12052,de=1563,data=12178,se=22352,ts=159132728,ls=64543,rc=0,fc=4294967295]
Transaction block size = 512
VFS: Can't find a valid MSDOS filesystem on dev 08:00.
begin:          vcard
fn:             Antonio Alfredo Rivas Ojanguren
n:              Rivas Ojanguren;Antonio Alfredo
email;internet: aeypil@teleline.es
note:           Cuaquier mensaje para el proyecto STARTEG utilizar la dirección aesypil@hotmail.com. Any message to STARTEG Project send it to aesypil@hotmail.com
x-mozilla-cpt:  ;-1
x-mozilla-html: FALSE
version:        2.1
end:            vcard


Reply to: