[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Re: sb 32 PnP

Shao Zhang wrote:
> 
> Hi,
>         From your /dev/sndstat, your midi device is working! Is this
> because of the new kernel, or you did some tricks with isapnp tools??
> 
>         Thanks in advance.
> 
>         PS. I can never get my midi device working under 2.0.35
> 
> Shao.

I have no idea--I'm _very_ new to this game.  I certainly didn't use any
"tricks" that I was aware of!  I've attached my isapnp.conf for what
that is worth (hope it isn't too big).

cheers

Richard
# $Id: pnpdump.c,v 1.16 1998/10/09 22:19:06 fox Exp $
# This is free software, see the sources for details.
# This software has NO WARRANTY, use at your OWN RISK
#
# For details of this file format, see isapnp.conf(5)
#
# For latest information on isapnp and pnpdump see:
# http://www.roestock.demon.co.uk/isapnptools/
#
# Compiler flags: -DREALTIME -DNEEDSETSCHEDULER
#
# Trying port address 0203
# Trying port address 020b
# Board 1 has serial identifier b1 00 00 3d cf 48 00 8c 0e

# (DEBUG)
(READPORT 0x020b)
(ISOLATE PRESERVE)
(IDENTIFY *)
(VERBOSITY 2)
(CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING

# Card 1: (serial identifier b1 00 00 3d cf 48 00 8c 0e)
# Vendor Id CTL0048, Serial Number 15823, checksum 0xB1.
# Version 1.0, Vendor version 1.0
# ANSI string -->Creative SB32 PnP<--
#
# Logical device id CTL0031
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE CTL0048/15823 (LD 0
#     ANSI string -->Audio<--

# Multiple choice time, choose one only !

#     Start dependent functions: priority preferred
#       IRQ 5.
#             High true, edge sensitive interrupt (by default)
 (INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 1.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
 (DMA 0 (CHANNEL 1))
#       Next DMA channel 5.
#             16 bit DMA only
#             Logical device is not a bus master
#             DMA may not execute in count by byte mode
#             DMA may execute in count by word mode
#             DMA channel speed in compatible mode
 (DMA 1 (CHANNEL 5))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0220
#             IO base alignment 1 bytes
#             Number of IO addresses required: 16
 (IO 0 (SIZE 16) (BASE 0x0220))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0330
#             Maximum IO base address 0x0330
#             IO base alignment 1 bytes
#             Number of IO addresses required: 2
 (IO 1 (SIZE 2) (BASE 0x0330))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0388
#             Maximum IO base address 0x0388
#             IO base alignment 1 bytes
#             Number of IO addresses required: 4
 (IO 2 (SIZE 4) (BASE 0x0388))

#       Start dependent functions: priority acceptable
#       IRQ 5, 7 or 10.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
#       Next DMA channel 5, 6 or 7.
#             16 bit DMA only
#             Logical device is not a bus master
#             DMA may not execute in count by byte mode
#             DMA may execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 5))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0280
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0300
#             Maximum IO base address 0x0330
#             IO base alignment 48 bytes
#             Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x0300))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0388
#             Maximum IO base address 0x0388
#             IO base alignment 1 bytes
#             Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0388))

#       Start dependent functions: priority acceptable
#       IRQ 5, 7 or 10.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
#       Next DMA channel 5, 6 or 7.
#             16 bit DMA only
#             Logical device is not a bus master
#             DMA may not execute in count by byte mode
#             DMA may execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 5))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0280
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0300
#             Maximum IO base address 0x0330
#             IO base alignment 48 bytes
#             Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x0300))

#       Start dependent functions: priority functional
#       IRQ 5, 7 or 10.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
#       Next DMA channel 5, 6 or 7.
#             16 bit DMA only
#             Logical device is not a bus master
#             DMA may not execute in count by byte mode
#             DMA may execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 5))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0280
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))

#       Start dependent functions: priority functional
#       IRQ 5, 7 or 10.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0280
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0300
#             Maximum IO base address 0x0330
#             IO base alignment 48 bytes
#             Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x0300))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0388
#             Maximum IO base address 0x0388
#             IO base alignment 1 bytes
#             Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0388))

#       Start dependent functions: priority functional
#       IRQ 5, 7 or 10.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0280
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0300
#             Maximum IO base address 0x0330
#             IO base alignment 48 bytes
#             Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x0300))

#       Start dependent functions: priority functional
#       IRQ 5, 7, 10 or 11.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0280
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
 (NAME "CTL0048/15823[0]{Audio               }")

#     End dependent functions
 (ACT Y)
))
#
# Logical device id CTL2011
#     Device supports vendor reserved register @ 0x38
#     Device supports vendor reserved register @ 0x39
#     Device supports vendor reserved register @ 0x3c
#     Device supports vendor reserved register @ 0x3e
#     Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE CTL0048/15823 (LD 1
#     Compatible device id PNP0600
#     ANSI string -->IDE<--

# Multiple choice time, choose one only !

#     Start dependent functions: priority preferred
#       IRQ 10.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 10 (MODE +E)))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0168
#             Maximum IO base address 0x0168
#             IO base alignment 1 bytes
#             Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0168))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x036e
#             Maximum IO base address 0x036e
#             IO base alignment 1 bytes
#             Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x036e))

#       Start dependent functions: priority acceptable
#       IRQ 11.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 11 (MODE +E)))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x01e8
#             Maximum IO base address 0x01e8
#             IO base alignment 1 bytes
#             Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x01e8))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x03ee
#             Maximum IO base address 0x03ee
#             IO base alignment 1 bytes
#             Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x03ee))

#       Start dependent functions: priority acceptable
#       IRQ 10, 11, 12 or 15.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 10 (MODE +E)))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0100
#             Maximum IO base address 0x01f8
#             IO base alignment 8 bytes
#             Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0100))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0300
#             Maximum IO base address 0x03fe
#             IO base alignment 2 bytes
#             Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x0300))

#       Start dependent functions: priority functional
#       IRQ 15.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 15 (MODE +E)))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0170
#             Maximum IO base address 0x0170
#             IO base alignment 1 bytes
#             Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0170))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0376
#             Maximum IO base address 0x0376
#             IO base alignment 1 bytes
#             Number of IO addresses required: 1
# (IO 1 (SIZE 1) (BASE 0x0376))
 (NAME "CTL0048/15823[1]{IDE                 }")

#     End dependent functions
# (ACT Y)
))
#
# Logical device id CTL0021
#     Device supports vendor reserved register @ 0x3a
#     Device supports vendor reserved register @ 0x3c
#     Device supports vendor reserved register @ 0x3e
#     Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE CTL0048/15823 (LD 2
#     ANSI string -->WaveTable<--

# Multiple choice time, choose one only !

#     Start dependent functions: priority preferred
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0620
#             Maximum IO base address 0x0620
#             IO base alignment 1 bytes
#             Number of IO addresses required: 4
 (IO 0 (SIZE 4) (BASE 0x0620))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0620
#             Maximum IO base address 0x0680
#             IO base alignment 32 bytes
#             Number of IO addresses required: 4
# (IO 0 (SIZE 4) (BASE 0x0620))
 (NAME "CTL0048/15823[2]{WaveTable           }")

#     End dependent functions
 (ACT Y)
))
#
# Logical device id CTL7001
#     Device supports vendor reserved register @ 0x38
#     Device supports vendor reserved register @ 0x39
#     Device supports vendor reserved register @ 0x3c
#     Device supports vendor reserved register @ 0x3e
#     Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE CTL0048/15823 (LD 3
#     Compatible device id PNPb02f
#     ANSI string -->Game<--
#     Logical device decodes 16 bit IO address lines
#         Minimum IO base address 0x0200
#         Maximum IO base address 0x0200
#         IO base alignment 1 bytes
#         Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0200))
))
## End tag... Checksum 0x00 (OK)

# Returns all cards to the "Wait for Key" state
(WAITFORKEY)
Reply to: