Problems with Adaptec 2842VL

[Ralf_Lederle@ccwn.fido.de (Ralf Lederle)]

Hi,

I can't install Debian 1.3.1, because my SCSI host adapter (Adaptec
AHA-2842VL, Bios 1.01) doesn't work. With an older Linux distribution
(Kernel 1.2.13) it runs without problems.

Here are the boot messages:

========================================================================
aic7xxx: Reading SEEPROM...done.
aic7xxx: Extended translation enabled.
aic7xxx: AHA-2840 Rev C and previous.
aic7ccc: Memory check yields 4 SCBs, paging not enabled.
aic7xxx: Using level sensitive interrupts.
AHA-2480 AT VLB SLOT 1.
    irq 11
    bus release time 40 bclks
    data fifo threshold 100%
    SCSI CHANNEL A:
        scsi id 7
        scsi selection timeout 256 ms
        scsi bus reset at power-on enabled
        scsi bus parity enabled
        scsi bus termination (low byte) disabled
aic7xxx: Downloading sequencer code...done.
aic7xxx: Resetting the SCSI bus...done.
qlogicisp: PCI bios not present
eata_dma: No BIOS32 extensions present. This driver release still depends on
it.
   Skipping scan for PCI HBAs.
aic7xxx: (aic7xxx_isr) Encountered spurious interrupt.
eata_pio: No BIOS32 extensions present. This driver release still depends on
it.
          Skipping scan for PCI HBAs.
Failed initialization of WD-7000 SCSI card!
PPA: unable to initialise controller at 0x378, error 2
scsi0: Adaptec AHA274x/284x/294x (EISA/VLB/PCI - Fast SCSI) 4.0/3.2/4.0
scsi : 1 host.
scsi0: Scanning channel A for devices.
scsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 0
Te
st Unit Ready 00 00 00 00 00
aic7xxx: (abort) Aborting scb 0, TCL 0/0/0
scsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 0
Te
st Unit Ready 00 00 00 00 00
aic7xxx: (abort) Aborting scb 0, TCL 0/0/0
SCSI host 0 abort (pid 0) timed out - resetting
SCSI bus is being reset for host 0 channel 0
aic7xxx: (reset) target/channel 0/0
aic7xxx: (abort_reset) scb state 0x1, Data-Out phase, SCSISIGI =0x0
aic7xxx: (reset_device) target/channel -1/A, active_scb 0
aic7xxx: (match_scb) comparing target/channel -1/A to scb 0/A
aic7xxx: (match_scb) comparing target/channel -1/A to scb 0/A
aic7xxx: (reset_channel) Resetting current channel A
aic7xxx: (reset_channel) Channel reset, sequencer restarted
aic7xxx: (done_aborted_scbs) Aborting scb 0, TCL=0/0/0
scsi0: BRKADRINT error (0x1)
  Illegal Host Access
Kernel panic: scsi0: BRKADRINT, error 0x1, seqaddr 0x0.

In swapper task - not syncing
========================================================================

Can anyone help me ?

Bye, Ralf


--
TO UNSUBSCRIBE FROM THIS MAILING LIST: e-mail the word "unsubscribe" to
debian-user-request@lists.debian.org . 
Trouble?  e-mail to templin@bucknell.edu .