Re: 1.1-Beta install problem with Buslogic controller
Larry Loos <larry@showme.net>:
> I was surprised that it claims:
> scsi0: Target 0: Synchronous at 10.0 mega-transfers/second
> I thought the 956C was a wide FAST scsi controller that ran at 20
> megabits per second.
The transfer number is correct. It does the same number of transfers
per second as the narrow devices, but moves twice as much data in each
transfer. Of course this is only to "wide" devices.
> I know the machine is okay because I had been using it to run a
> Slackware version of Linux with kernel 1.2.13.
OK, I have appended a long list of driver configuration arguments to
the end of this message. The driver is different since 1.2.13 . Please
try to use the arguments to disable stuff like tagged queueing. You would
use them at the "boot: " prompt of the installation floppy, and you would
have to edit /etc/lilo.config to put them in your LILO configuration
or give them as arguments to LOADLIN.
IF you can't figure it out, please write to Leonard N. Zubkoff
at <lnz@dandelion.com>. He is the author of the driver, and he wants
to know about any cases where it does not work. Even if you do figure
it out, it might be a good idea to tell him what you had to do.
> Using the old slackware install I never could get LILO to work but
> Loadlin was fine.
Sometimes this is a BIOS problem. If LILO still doesn't work, try to use
it on a partition that is all below 1024 cylinders.
> Please don't tell me I must use Slackware or Red Hat.
They don't yet offer the 2.0 kernel yet and we do, that's all. Falling back
to an older kernel is easy enough to do with Debian, but I bet you will
be able to work around this.
Thanks
Bruce
/*
BusLogic_Setup handles processing of Kernel Command Line Arguments.
For the BusLogic driver, a Kernel command line entry comprises the driver
identifier "BusLogic=" optionally followed by a comma-separated sequence of
integers and then optionally followed by a comma-separated sequence of
strings. Each command line entry applies to one BusLogic Host Adapter.
Multiple command line entries may be used in systems which contain multiple
BusLogic Host Adapters.
The first integer specified is the I/O Address at which the Host Adapter is
located. If unspecified, it defaults to 0 which means to apply this entry to
the first BusLogic Host Adapter found during the default probe sequence. If
any I/O Address parameters are provided on the command line, then the default
probe sequence is omitted.
The second integer specified is the Tagged Queue Depth to use for Target
Devices that support Tagged Queuing. The Queue Depth is the number of SCSI
commands that are allowed to be concurrently presented for execution. If
unspecified, it defaults to 0 which means to use a value determined
automatically based on the Host Adapter's Total Queue Depth and the number,
type, speed, and capabilities of the detected Target Devices. For Host
Adapters that require ISA Bounce Buffers, the Tagged Queue Depth is
automatically set to BusLogic_TaggedQueueDepth_BB to avoid excessive
preallocation of DMA Bounce Buffer memory. Target Devices that do not
support Tagged Queuing use a Queue Depth of BusLogic_UntaggedQueueDepth.
The third integer specified is the Bus Settle Time in seconds. This is
the amount of time to wait between a Host Adapter Hard Reset which initiates
a SCSI Bus Reset and issuing any SCSI Commands. If unspecified, it defaults
to 0 which means to use the value of BusLogic_DefaultBusSettleTime.
The fourth integer specified is the Local Options. If unspecified, it
defaults to 0. Note that Local Options are only applied to a specific Host
Adapter.
The fifth integer specified is the Global Options. If unspecified, it
defaults to 0. Note that Global Options are applied across all Host
Adapters.
The string options are used to provide control over Tagged Queuing and Error
Recovery. If both Tagged Queuing and Error Recovery strings are provided, the
Tagged Queuing specification string must come first.
The Tagged Queuing specification begins with "TQ:" and allows for explicitly
specifying whether Tagged Queuing is permitted on Target Devices that support
it. The following specification options are available:
TQ:Default Tagged Queuing will be permitted based on the firmware
version of the BusLogic Host Adapter and based on
whether the Tagged Queue Depth value allows queuing
multiple commands.
TQ:Enable Tagged Queuing will be enabled for all Target Devices
on this Host Adapter overriding any limitation that
would otherwise be imposed based on the Host Adapter
firmware version.
TQ:Disable Tagged Queuing will be disabled for all Target Devices
on this Host Adapter.
TQ:<Per-Target-Spec> Tagged Queuing will be controlled individually for each
Target Device. <Per-Target-Spec> is a sequence of "Y",
"N", and "X" characters. "Y" enabled Tagged Queuing,
"N" disables Tagged Queuing, and "X" accepts the
default based on the firmware version. The first
character refers to Target Device 0, the second to
Target Device 1, and so on; if the sequence of "Y",
"N", and "X" characters does not cover all the Target
Devices, unspecified characters are assumed to be "X".
Note that explicitly requesting Tagged Queuing may lead to problems; this
facility is provided primarily to allow disabling Tagged Queuing on Target
Devices that do not implement it correctly.
The Error Recovery Strategy specification begins with "ER:" and allows for
explicitly specifying the Error Recovery action to be performed when
ResetCommand is called due to a SCSI Command failing to complete
successfully. The following specification options are available:
ER:Default Error Recovery will select between the Hard Reset and
Bus Device Reset options based on the recommendation
of the SCSI Subsystem.
ER:HardReset Error Recovery will initiate a Host Adapter Hard Reset
which also causes a SCSI Bus Reset.
ER:BusDeviceReset Error Recovery will send a Bus Device Reset message to
the individual Target Device causing the error. If
Error Recovery is again initiated for this Target
Device and no SCSI Command to this Target Device has
completed successfully since the Bus Device Reset
message was sent, then a Hard Reset will be attempted.
ER:None Error Recovery will be suppressed. This option should
only be selected if a SCSI Bus Reset or Bus Device
Reset will cause the Target Device to fail completely
and unrecoverably.
ER:<Per-Target-Spec> Error Recovery will be controlled individually for each
Target Device. <Per-Target-Spec> is a sequence of "D",
"H", "B", and "N" characters. "D" selects Default, "H"
selects Hard Reset, "B" selects Bus Device Reset, and
"N" selects None. The first character refers to Target
Device 0, the second to Target Device 1, and so on; if
the sequence of "D", "H", "B", and "N" characters does
not cover all the possible Target Devices, unspecified
characters are assumed to be "D".
*/
--
Pixar's "Toy Story": Over 1/3 Billion dollars world box office so far.
Bruce Perens AB6YM Bruce@Pixar.com http://www.hams.com/
Reply to: