HELP: usb webcamera (spyc@m 300, module stv680 )!
Help, my webcamerapicture are on my xawtv!
Am I on tv?
I have for some time now, tried to get a program "pencam" to work...
("pencam" grab still picture from the usb-camera.)
Program tells only tell me: "pencam_open error: Cannot open camera...",
and it does not have any "man" page!
I read the documents, google.. and etc, BUT tells me nothing.
After my own head installed "usbview", "usbutils" And "usbmgr".
BUT "pencam" didn't work after that, instead the video image from the
camera appeared on "xawtv"!
( HEY IM ON TV *not* )
-Strange!!
I also have a tv-card, and Im now shure that module stv680 steels it's
property.
It seams like I can't have two video source's.
*** SO, to the point. I want: ***
-Help with getting the "pencam", program to work.
-Having more than one video-source.
( I made it work with two video sources ones, but when I reboot the
system the same problem appeared ( I didn't remember all the steps I
made ), so I sure stv680 interferes. )
Here is some data:
Returns of "lspci"
00:00.0 Host bridge: Intel Corp. 440LX/EX - 82443LX/EX Host bridge (rev 03)
00:01.0 PCI bridge: Intel Corp. 440LX/EX - 82443LX/EX AGP bridge (rev 03)
00:04.0 ISA bridge: Intel Corp. 82371AB PIIX4 ISA (rev 01)
00:04.1 IDE interface: Intel Corp. 82371AB PIIX4 IDE (rev 01)
00:04.2 USB Controller: Intel Corp. 82371AB PIIX4 USB (rev 01)
00:04.3 Bridge: Intel Corp. 82371AB PIIX4 ACPI (rev 01)
00:06.0 SCSI storage controller: Adaptec AIC-7880U (rev 01)
00:0b.0 Multimedia video controller: Brooktree Corporation Bt878 (rev 02)
00:0b.1 Multimedia controller: Brooktree Corporation Bt878 (rev 02)
00:0c.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8029(AS)
01:00.0 VGA compatible controller: ATI Technologies Inc 3D Rage Pro AGP
1X/2X (rev 5c)
Return of "lsusb":
Bus 001 Device 001: ID 0000:0000 Virtual Hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.00
bDeviceClass 9 Hub
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x0000 Virtual
idProduct 0x0000 Hub
bcdDevice 0.00
iManufacturer 0
iProduct 2 USB UHCI Root Hub
iSerial 1 b400
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x40
Self Powered
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type none
wMaxPacketSize 8
bInterval 255
Language IDs: (length=4)
0000 (null)((null))
Bus 001 Device 002: ID 0553:0202 VLSI Vision Ltd.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 255 Vendor Specific Class
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x0553 VLSI Vision Ltd.
idProduct 0x0202
bcdDevice 0.00
iManufacturer 1 STMicroelectronics
iProduct 2 USB Dual-mode Camera
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 34
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xa0
Remote Wakeup
MaxPower 70mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 0
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 1
bNumEndpoints 1
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type none
wMaxPacketSize 64
bInterval 0
Language IDs: (length=14)
0409 English(US)
040c French(French)
0407 German(German)
0410 Italian(Italian)
0c0a Spanish(Modern)
0416 Po rtugese(Portugese)
Return of "dmesg":
Linux version 2.4.18-bf2.4 (root@zombie) (gcc version 2.95.4 20011002
(Debian prerelease)) #1 Son Apr 14 09:53:28 CEST 2002
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000007ffd000 (usable)
BIOS-e820: 0000000007ffd000 - 0000000007fff000 (ACPI data)
BIOS-e820: 0000000007fff000 - 0000000008000000 (ACPI NVS)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
On node 0 totalpages: 32765
zone(0): 4096 pages.
zone(1): 28669 pages.
zone(2): 0 pages.
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Kernel command line: BOOT_IMAGE=Linux ro root=307 hdb=ide-scsi
ide_setup: hdb=ide-scsi
Initializing CPU#0
Detected 300.686 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 599.65 BogoMIPS
Memory: 125672k/131060k available (1783k kernel code, 5000k reserved,
549k data, 280k init, 0k highmem)
Dentry-cache hash table entries: 16384 (order: 5, 131072 bytes)
Inode-cache hash table entries: 8192 (order: 4, 65536 bytes)
Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
CPU: Before vendor init, caps: 0080fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
CPU: After vendor init, caps: 0080fbff 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0080fbff 00000000 00000000 00000000
CPU: Common caps: 0080fbff 00000000 00000000 00000000
CPU: Intel Pentium II (Klamath) stepping 04
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 300.6748 MHz.
..... host bus clock speed is 66.8164 MHz.
cpu: 0, clocks: 668164, slice: 334082
CPU0<T0:668160,T1:334064,D:14,S:334082,C:668164>
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xf0750, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Using IRQ router PIIX [8086/7110] at 00:04.0
Limiting direct PCI/PCI transfers.
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Diskquotas version dquot_6.4.0 initialized
Journalled Block Device driver loaded
vga16fb: initializing
vga16fb: mapped to 0xc00a0000
Console: switching to colour frame buffer device 80x30
fb0: VGA16 VGA frame buffer device
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ
SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10e
block: 128 slots per queue, batch=32
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller on PCI bus 00 dev 21
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xb800-0xb807, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xb808-0xb80f, BIOS settings: hdc:pio, hdd:pio
hda: IBM-DTLA-305040, ATA DISK drive
hdb: CR-2801TE, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: 66055248 sectors (33820 MB) w/380KiB Cache, CHS=4111/255/63
ide-floppy driver 0.97.sv
Partition check:
hda: hda1 hda2 < hda5 hda6 hda7 hda8 >
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Loading I2O Core - (c) Copyright 1999 Red Hat Software
I2O configuration manager v 0.04.
(C) Copyright 1999 Red Hat Software
loop: loaded (max 8 devices)
Compaq CISS Driver (v 2.4.5)
ne2k-pci.c:v1.02 10/19/2000 D. Becker/P. Gortmaker
http://www.scyld.com/network/ne2k-pci.html
PCI: Found IRQ 11 for device 00:0c.0
eth0: RealTek RTL-8029 found at 0xa800, IRQ 11, 00:00:E8:F0:7E:3D.
HDLC support module revision 1.02 for Linux 2.4
Cronyx Ltd, Synchronous PPP and CISCO HDLC (c) 1994
Linux port (c) 1998 Building Number Three Ltd & Jan "Yenya" Kasprzak.
ide-floppy driver 0.97.sv
Promise Fasttrak(tm) Softwareraid driver 0.03beta: No raid array found
Highpoint HPT370 Softwareraid driver for linux version 0.01
No raid array found
SCSI subsystem driver Revision: 1.00
Red Hat/Adaptec aacraid driver, Apr 14 2002
PCI: Found IRQ 10 for device 00:06.0
PCI: Sharing IRQ 10 with 00:04.2
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.4
<Adaptec aic7880 Ultra SCSI adapter>
aic7880: Ultra Wide Channel A, SCSI Id=1, 16/253 SCBs
Vendor: IBM Model: DCAS-34330W Rev: S65A
Type: Direct-Access ANSI SCSI revision: 02
(scsi0:A:0): 40.000MB/s transfers (20.000MHz, offset 8, 16bit)
Vendor: NEC Model: CD-ROM DRIVE:464 Rev: 1.05
Type: CD-ROM ANSI SCSI revision: 02
(scsi0:A:2): 20.000MB/s transfers (20.000MHz, offset 15)
scsi0:A:0:0: Tagged Queuing enabled. Depth 8
DC390: 0 adapters found
3ware Storage Controller device driver for Linux v1.02.00.016.
3w-xxxx: No cards with valid units found.
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sda: 8467200 512-byte hdwr sectors (4335 MB)
sda: sda1 sda2 < sda5 >
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 2, lun 0
sr0: scsi-1 drive
Uniform CD-ROM driver Revision: 3.12
i2o_scsi.c: Version 0.0.1
chain_pool: 0 bytes @ c125c320
(512 byte buffers X 4 can_queue X 0 i2o controllers)
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 8192 bind 8192)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 280k freed
Adding Swap: 248968k swap-space (priority -1)
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,7), internal journal
isapnp: Scanning for PnP cards...
isapnp: Card 'Crystal Codec'
isapnp: 1 Plug & Play card detected total
ad1848/cs4248 codec driver Copyright (C) by Hannu Savolainen 1993-1996
ad1848: No ISAPnP cards found, trying standard ones...
cs4232: set synthio and synthirq to use the wavefront facilities.
scsi1 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: MITSUMI Model: CR-2801TE Rev: 1.10
Type: CD-ROM ANSI SCSI revision: 02
Attached scsi CD-ROM sr1 at scsi1, channel 0, id 0, lun 0
sr1: scsi3-mmc drive: 8x/8x writer xa/form2 cdda tray
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 94M
agpgart: Detected Intel 440LX chipset
agpgart: AGP aperture is 64M @ 0xe4000000
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 10:29:43 Apr 14 2002
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 10 for device 00:04.2
PCI: Sharing IRQ 10 with 00:06.0
usb-uhci.c: USB UHCI at I/O 0xb400, IRQ 10
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
Linux video capture interface: v1.00
usb.c: registered new driver stv680
stv680.c: [usb_stv680_init:1656] STV(i): usb camera driver version v0.24
registering
stv680.c: STV0680 USB Camera Driver v0.24
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,8), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
parport0: irq 7 detected
lp0: using parport0 (polling).
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
hub.c: USB new device connect on bus1/2, assigned device number 2
stv680.c: [stv680_probe:1555] STV(i): STV0680 camera found.
stv680.c: [stv680_probe:1583] STV(i): registered new video device: video0
stv680.c: [stv_init:428] STV(i): QVGA is supported
stv680.c: [stv_init:444] STV(i): Camera has 0 pictures.
stv680.c: [stv_init:475] STV(i): Video Mode set to QVGA
stv680.c: [stv_init:428] STV(i): QVGA is supported
stv680.c: [stv_init:444] STV(i): Camera has 0 pictures.
stv680.c: [stv_init:475] STV(i): Video Mode set to QVGA
stv680.c: [stv_init:428] STV(i): QVGA is supported
stv680.c: [stv_init:444] STV(i): Camera has 0 pictures.
stv680.c: [stv_init:475] STV(i): Video Mode set to QVGA
usb.c: deregistering driver stv680
stv680.c: [usb_stv680_remove_disconnected:1611] STV(i): STV0680 disconnected
stv680.c: [usb_stv680_exit:1665] STV(i): driver deregistered
Linux video capture interface: v1.00
i2c-core.o: i2c core module
i2c-algo-bit.o: i2c bit algorithm module
bttv: driver version 0.7.83 loaded
bttv: using 2 buffers with 2080k (4160k total) for capture
bttv: Host bridge is Intel Corp. 440LX/EX - 82443LX/EX Host bridge
bttv: Host bridge needs ETBF enabled.
bttv: Bt8xx card found (0).
PCI: Found IRQ 10 for device 00:0b.0
PCI: Sharing IRQ 10 with 00:0b.1
bttv0: Bt878 (rev 2) at 00:0b.0, irq: 10, latency: 32, memory: 0xe3000000
bttv0: detected: AVerMedia TVPhone98 [card=41], PCI subsystem ID is
1461:0003
bttv0: using: BT878(AVerMedia TVPhone 98) [card=41,autodetected]
bttv0: enabling ETBF (430FX/VP3 compatibilty)
i2c-core.o: adapter bt848 #0 registered as adapter 0.
bttv0: Avermedia eeprom[0x4811]: tuner=5
bttv0: i2c: checking for MSP34xx @ 0x80... not found
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
tvaudio: TV audio decoder + audio/video mux driver
tvaudio: known chips:
tda9840,tda9873h,tda9874a,tda9850,tda9855,tea6300,tea6420,tda8425,pic16c54
(PV951)
i2c-core.o: driver generic i2c audio driver registered.
i2c-core.o: driver i2c TV tuner driver registered.
tuner: chip found @ 0xc2
bttv0: i2c attach [client=Philips PAL,ok]
i2c-core.o: client [Philips PAL] registered to adapter [bt848 #0](pos. 0).
bttv0: PLL: 28636363 => 35468950 ... ok
**********Thats all
--
Mvh
--
Name: "Per Blomqvist"
Tel.nr: "+46 070-3355632"
E-mail: "per.blomqvist@telia.com"
Webpage: "http://niffeln.netfirms.com/";
Reply to: