>
> -Tengo un debian sarge con kerrnel 2.6.8-2-386, tengo configurado una
> tarjeta de red integrada de la maquina (eth0) donde funciona
> perfectamente una conexion Banda Ancha. Deseo instalar una segunda
> tarjeta de red para poder ver la lan de la empresa ya que la intencion
> es instalar squid+shorewall.
>
> Al ejecutar el comando lspci obtengo:
>
> # lspci | grep Ethernet
> 0000:03:06.0 Ethernet controller: Sundance Technology Inc: Unknown
> device 0200 (rev 31)
> 0000:03:0a.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
> RTL-8139/8139C/8139C+ (rev 10)
>
> Luego hice #modconf , y agregue el modulo "sundance" (Sundance Alta
> PCI Ethernet support), reinicio la maquina. Posteriormente verifico
> con dsmeg:
>
> ~# dmesg|grep eth
> eth0: RealTek RTL8139 at 0xc800, 00:0b:6a:9a:b0:ce, IRQ 201
> eth0: Identified 8139 chip type 'RTL-8101'
> eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
> eth0: no IPv6 routers present
>
> Agrego la interfaz al archivo /etc/network/interfaces, como sigue
>
> ------------------------------------------------------------------------------------
>
> # This file describes the network interfaces available on your system
> # and how to activate them. For more information, see interfaces(5).
>
> # The loopback network interface
> auto lo
> iface lo inet loopback
>
> # The primary network interface
> auto eth0
> iface eth0 inet dhcp
> name Tarjeta de red Ethernet
>
>
> iface eth1 inet static
> name Tarjeta de red Ethernet
> address 192.168.32.2
> netmask 255.255.255.0
> broadcast 192.168.32.255
> network 192.168.32.0
> gateway 192.168.32.7
>
> auto eth1
> -------------------------------------
>
> Aun asi no puedo ver la red local. Anexo la salida del comando ifconfig:
> # ifconfig
> eth0 Link encap:Ethernet HWaddr 00:0B:6A:9A:B0:CE
> inet addr:200.109.16.73 Bcast:200.109.16.255
> Mask:255.255.248.0
> inet6 addr: fe80::20b:6aff:fe9a:b0ce/64 Scope:Link
> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
> RX packets:6578 errors:0 dropped:0 overruns:0 frame:0
> TX packets:1201 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:1000
> RX bytes:822396 (803.1 KiB) TX bytes:250484 (244.6 KiB)
> Interrupt:201 Base address:0xc800
>
> lo Link encap:Local Loopback
> inet addr:127.0.0.1 Mask:255.0.0.0
> inet6 addr: ::1/128 Scope:Host
> UP LOOPBACK RUNNING MTU:16436 Metric:1
> RX packets:36741 errors:0 dropped:0 overruns:0 frame:0
> TX packets:36741 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:0
> RX bytes:8829639 (8.4 MiB) TX bytes:8829639 (8.4 MiB)
>
> Visite la pagina de Advantek y descarge el drive para Linux pero solo
> estan los compatibles con los modulos 2.4 y 2.2
>
> Gracias de Antemano y VIVA DEBIAN y el GNU/LINUX!!!
>
>
Deberías de cargar el module sundance en /etc/modules para que se cargue
no parece estar cargándose. Asi lo tengo yo con una tarjeta encore que
usa el module sundance. Saludos.
--
To UNSUBSCRIBE, email to debian-user-spanish-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org