problemas con tarjeta d red
Wenasss , sigo pegándome con woody, montando un router. Cuando casi lo
tenia terminado ahora me sale un error al inicio:
eth1: allocate dma memory failed
eth1: allocate dma memory failed
y nada mas hacer login ejecuto ifconfig y solo aparece eth0 ( RealTek RTL8139 )
y localhost, eht1 ( Ovislink G83820-32 -chip : VT6122) no sale.
Si ejecuto ifup eth1 me produce esta salida:
ifup: interface eth1 already configured
Si ejecuto ifdown eth1 (sin problemas) pero vuelvo a ejecutar ifup eth1 y ahora
me sale esto:
eth1: allocate dma memory failed
SIOCSIFFLAGS: Cannot allocate memory
eth1: allocate dma memory failed
SIOCSIFFLAGS: Cannot allocate memory
Buscando por google no aparece este error, alguno parecido dicen que es un conflicto
de irqs,y aconsejan desactivar la opción del plug&play de la bios pero en mi equipo
( Intel Pentium MMX, 166 MHz ) no aparece esa opción.
Lo mas raro es que a veces aparece el error y no me funciona la tarjeta de red de la
lan interna ( la que hace nat a la red interna ) y otras veces funciona sin hacer nada.
Ya no se que hacer, o si dar el equipo por muerto.
Os pego aquí la salida del dmesg por si veis algo para solucionarlo.
> Linux version 2.4.18 (root@wiggum) (gcc version 2.95.4 20011002 (Debian prerelease)) #2 SMP lun mar 28 00:19:37 CEST 2005
> BIOS-provided physical RAM map:
> BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
> BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
> BIOS-e820: 0000000000100000 - 0000000001000000 (usable)
> BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
> On node 0 totalpages: 4096
> zone(0): 4096 pages.
> zone(1): 0 pages.
> zone(2): 0 pages.
> No local APIC present or hardware disabled
> Kernel command line: auto BOOT_IMAGE=Linux ro root=302
> Initializing CPU#0
> Detected 166.405 MHz processor.
> Console: colour VGA+ 80x25
> Calibrating delay loop... 331.77 BogoMIPS
> Memory: 12356k/16384k available (1955k kernel code, 3644k reserved, 628k data, 288k init, 0k highmem)
> Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
> Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
> Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
> Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
> Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
> CPU: Before vendor init, caps: 008001bf 00000000 00000000, vendor = 0
> Intel Pentium with F0 0F bug - workaround enabled.
> CPU: After vendor init, caps: 008001bf 00000000 00000000 00000000
> CPU: After generic, caps: 008001bf 00000000 00000000 00000000
> CPU: Common caps: 008001bf 00000000 00000000 00000000
> Checking 'hlt' instruction... OK.
> Checking for popad bug... OK.
> POSIX conformance testing by UNIFIX
> mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
> mtrr: detected mtrr type: none
> CPU: Before vendor init, caps: 008001bf 00000000 00000000, vendor = 0
> CPU: After vendor init, caps: 008001bf 00000000 00000000 00000000
> CPU: After generic, caps: 008001bf 00000000 00000000 00000000
> CPU: Common caps: 008001bf 00000000 00000000 00000000
> CPU0: Intel Pentium MMX stepping 03
> per-CPU timeslice cutoff: 159.89 usecs.
> SMP motherboard not detected.
> Local APIC not detected. Using dummy APIC emulation.
> Waiting on wait_init_idle (map = 0x0)
> All processors have done init_idle
> PCI: PCI BIOS revision 2.10 entry at 0xfb470, last bus=0
> PCI: Using configuration type 1
> PCI: Probing PCI hardware
> Activating ISA DMA hang workarounds.
> Linux NET4.0 for Linux 2.4
> Based upon Swansea University Computer Society NET3.039
> Initializing RT netlink socket
> Starting kswapd
> VFS: Diskquotas version dquot_6.4.0 initialized
> Journalled Block Device driver loaded
> vga16fb: initializing
> vga16fb: mapped to 0xc00a0000
> Console: switching to colour frame buffer device 80x30
> fb0: VGA16 VGA frame buffer device
> Detected PS/2 Mouse Port.
> pty: 256 Unix98 ptys configured
> Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
> ttyS00 at 0x03f8 (irq = 4) is a 16550A
> ttyS01 at 0x02f8 (irq = 3) is a 16550A
> ttyS02 at 0x03e8 (irq = 4) is a 16550A
> Real Time Clock Driver v1.10e
> block: 64 slots per queue, batch=16
> RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
> Uniform Multi-Platform E-IDE driver Revision: 6.31
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> VP_IDE: IDE controller on PCI bus 00 dev 39
> VP_IDE: chipset revision 2
> VP_IDE: not 100% native mode: will probe irqs later
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> VP_IDE: VIA vt82c586 (rev 02) IDE MWDMA16 controller on pci00:07.1
> ide0: BM-DMA at 0x6000-0x6007, BIOS settings: hda:DMA, hdb:pio
> ide1: BM-DMA at 0x6008-0x600f, BIOS settings: hdc:DMA, hdd:pio
> hda: ST32122A, ATA DISK drive
> hdc: SAMSUNG SCR-3232, ATAPI CD/DVD-ROM drive
> ide2: ports already in use, skipping probe
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> ide1 at 0x170-0x177,0x376 on irq 15
> hda: 4124736 sectors (2112 MB), CHS=1023/64/63, (U)DMA
> hdc: ATAPI 32X CD-ROM drive, 128kB Cache, DMA
> Uniform CD-ROM driver Revision: 3.12
> ide-floppy driver 0.97.sv
> Partition check:
> hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 >
> FDC 0 is an 8272A
> Loading I2O Core - (c) Copyright 1999 Red Hat Software
> I2O configuration manager v 0.04.
> (C) Copyright 1999 Red Hat Software
> loop: loaded (max 8 devices)
> Compaq CISS Driver (v 2.4.5)
> 8139cp 10/100 PCI Ethernet driver v0.0.6 (Nov 19, 2001)
> 8139cp: pci dev 00:0b.0 (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
> 8139cp: Try the "8139too" driver instead.
> 8139too Fast Ethernet driver 0.9.24
> eth0: RealTek RTL8139 Fast Ethernet at 0xc181c000, 00:48:54:6c:b9:47, IRQ 10
> eth0: Identified 8139 chip type 'RTL-8139B'
> HDLC support module revision 1.02 for Linux 2.4
> Cronyx Ltd, Synchronous PPP and CISCO HDLC (c) 1994
> Linux port (c) 1998 Building Number Three Ltd & Jan "Yenya" Kasprzak.
> ide-floppy driver 0.97.sv
> Promise Fasttrak(tm) Softwareraid driver 0.03beta: No raid array found
> Highpoint HPT370 Softwareraid driver for linux version 0.01
> No raid array found
> SCSI subsystem driver Revision: 1.00
> Red Hat/Adaptec aacraid driver, Mar 28 2005
> DC390: 0 adapters found
> 3ware Storage Controller device driver for Linux v1.02.00.016.
> 3w-xxxx: No cards with valid units found.
> request_module[scsi_hostadapter]: Root fs not mounted
> request_module[scsi_hostadapter]: Root fs not mounted
> Linux Kernel Card Services 3.1.22
> options: [pci] [cardbus] [pm]
> i2o_scsi.c: Version 0.0.1
> chain_pool: 0 bytes @ c004d540
> (512 byte buffers X 4 can_queue X 0 i2o controllers)
> NET4: Linux TCP/IP 1.0 for NET4.0
> IP Protocols: ICMP, UDP, TCP, IGMP
> IP: routing cache hash table of 512 buckets, 4Kbytes
> TCP: Hash tables configured (established 1024 bind 1024)
> NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
> ds: no socket drivers loaded!
> kjournald starting. Commit interval 5 seconds
> EXT3-fs: mounted filesystem with ordered data mode.
> VFS: Mounted root (ext3 filesystem) readonly.
> Freeing unused kernel memory: 288k freed
> Adding Swap: 195544k swap-space (priority -1)
> EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,2), internal journal
> VIA Networking Velocity Family Gigabit Ethernet Adapter Driver Ver. 1.11
> Copyright (c) 2002, 2003 VIA Networking Technologies, Inc.
> eth1: VIA Networking Velocity Family Gigabit Ethernet Adapter
> eth1: MAC=00:05:1C:20:52:92 IO=0x6100 Mem=0xc1840000 IRQ=11
> kjournald starting. Commit interval 5 seconds
> EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,1), internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
> kjournald starting. Commit interval 5 seconds
> EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,5), internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
> kjournald starting. Commit interval 5 seconds
> EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,7), internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
> kjournald starting. Commit interval 5 seconds
> EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,6), internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
> eth0: Setting 100mbps full-duplex based on auto-negotiated partner ability c5e1.
> eth1: allocate dma memory failed
> eth1: allocate dma memory failed
--
Salu2,
Wootux
============================================================
Por favor, NO utilice formatos de archivo propietarios para el
intercambio de documentos, como DOC y XLS, sino HTML, RTF, TXT, CSV o
cualquier otro que no obligue a utilizar un programa de un
fabricante concreto para tratar la información contenida en él.
============================================================
---- Europa libre de patentes de software. Open source is the way.
Este e-mail ha sido escaneado por un antivirus actualizado.
Escrito bajo la licencia Creative Commons: http://creativecommons.org/licenses/by-nc-sa/2.0/es/
Reply to: