Celular motorola a1200e monta, mas com erros
Fala povo,
Comprei um smartphone motorola a1200e. Estou tentando fazer ele montar
como armazenamento usb no meu debian sid. Quando configuro o telefone
pra 'usb - modo modem', tudo beleza, o dmesg mostra essas linhas aí, e
eu consigo fazer o kmobiletools conversar com o a1200e.
dmesg (só a parte relevante):
[ 80.799134] hub 5-0:1.0: unable to enumerate USB device on port 2
[ 81.043462] usb 1-2: new full speed USB device using uhci_hcd and
address 2
[ 79.592761] usb 1-2: configuration #1 chosen from 1 choice
[ 79.601595] usb 1-2: New USB device found, idVendor=22b8, idProduct=3802
[ 79.601604] usb 1-2: New USB device strings: Mfr=3, Product=2,
SerialNumber=0
[ 79.601607] usb 1-2: Product: Motorola USB Modem
[ 79.601684] usb 1-2: Manufacturer: Motorola
[ 79.696763] cdc_acm 1-2:1.0: ttyACM0: USB ACM device
[ 79.699290] usbcore: registered new interface driver cdc_acm
[ 79.699299] drivers/usb/class/cdc-acm.c: v0.25:USB Abstract Control
Model driver for USB modems and ISDN adapters
bruno@neutron:~$ ls -l /dev/ttyACM0
crw-rw---- 1 root dialout 166, 0 Set 1 21:11 /dev/ttyACM0
Mas quando configuro o a1200e pra armazenamento usb, o dmesg mostra isso:
[ 4051.754035] usb 1-2: new full speed USB device using uhci_hcd and
address 4
[ 4051.918093] usb 1-2: configuration #1 chosen from 1 choice
[ 4051.936104] usb 1-2: New USB device found, idVendor=22b8, idProduct=608d
[ 4051.936113] usb 1-2: New USB device strings: Mfr=3, Product=2,
SerialNumber=5
[ 4051.936116] usb 1-2: Product: Phone
[ 4051.936118] usb 1-2: Manufacturer: Motorola Inc.
[ 4051.936120] usb 1-2: SerialNumber: 000000000000
[ 4052.019850] Initializing USB Mass Storage driver...
[ 4052.020332] scsi2 : SCSI emulation for USB Mass Storage devices
[ 4052.020633] usbcore: registered new interface driver usb-storage
[ 4052.020643] USB Mass Storage support registered.
[ 4151.309615] usb-storage: device found at 4
[ 4151.309622] usb-storage: waiting for device to settle before scanning
[ 4056.899382] usb-storage: device scan complete
[ 4156.241569] scsi 2:0:0:0: Direct-Access Motorola
Phone PQ: 0 ANSI: 4
[ 4156.393557] sd 2:0:0:0: [sdb] 3984896 512-byte hardware sectors (2040 MB)
[ 4156.397207] sd 2:0:0:0: [sdb] Write Protect is off
[ 4156.397207] sd 2:0:0:0: [sdb] Mode Sense: 10 00 00 00
[ 4156.397207] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 4156.401732] sd 2:0:0:0: [sdb] 3984896 512-byte hardware sectors (2040 MB)
[ 4156.404543] sd 2:0:0:0: [sdb] Write Protect is off
[ 4156.404543] sd 2:0:0:0: [sdb] Mode Sense: 10 00 00 00
[ 4156.404543] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 4156.404543] sdb: sdb1
[ 4156.416689] sdb: p1 exceeds device capacity
[ 4156.416689] sd 2:0:0:0: [sdb] Attached SCSI disk
[ 4156.416689] sd 2:0:0:0: Attached scsi generic sg2 type 0
[ 4157.770041] attempt to access beyond end of device
[ 4157.770041] sdb: rw=0, want=3985272, limit=3984896
[ 4157.770041] Buffer I/O error on device sdb1, logical block 3985024
[ 4157.770041] attempt to access beyond end of device
[ 4157.770041] sdb: rw=0, want=3985273, limit=3984896
[ 4157.770041] Buffer I/O error on device sdb1, logical block 3985025
[ 4157.770041] attempt to access beyond end of device
[ 4157.770041] sdb: rw=0, want=3985274, limit=3984896
[ 4157.770041] Buffer I/O error on device sdb1, logical block 3985026
[ 4157.770041] attempt to access beyond end of device
[ 4157.770041] sdb: rw=0, want=3985275, limit=3984896
[ 4157.770041] Buffer I/O error on device sdb1, logical block 3985027
[ 4157.770041] attempt to access beyond end of device
[ 4157.770041] sdb: rw=0, want=3985276, limit=3984896
[ 4157.770041] Buffer I/O error on device sdb1, logical block 3985028
[ 4157.770041] attempt to access beyond end of device
[ 4157.770041] sdb: rw=0, want=3985277, limit=3984896
[ 4157.770041] Buffer I/O error on device sdb1, logical block 3985029
[ 4157.770041] attempt to access beyond end of device
[ 4157.770041] sdb: rw=0, want=3985278, limit=3984896
[ 4157.770041] Buffer I/O error on device sdb1, logical block 3985030
[ 4157.770041] attempt to access beyond end of device
[ 4157.770041] sdb: rw=0, want=3985279, limit=3984896
(várias linhas iguais...)
[ 4058.683393] sdb: rw=0, want=3985408, limit=3984896
[ 4074.620621] FAT: utf8 is not a recommended IO charset for FAT
filesystems, filesystem will be case sensitive!
E embora dê esses erros ele monta e eu vejo o conteúdo do cartão t-flash
que o a1200e tem, podendo inclusive gravar e apagar arquivos. Mas essas
linhas todas de erro não estão me encorajando muito a mexer nele assim.
Pra gravar e apagar arquivos no cartão -flash, preciso montá-lo com um
leitor de cartões extra. Gostaria de poder montar direto pelo telefone.
O que vocês acham?
Debian sid com kde 3.5.9 num acer dual-core.
bruno@neutron:~$ uname -a
Linux neutron 2.6.25-2-686-bigmem #1 SMP Fri Jun 27 04:07:13 UTC 2008
i686 GNU/Linux
valeu!
bruno
Reply to: