Modem Yiso no Debian Etch Amd64
Olá, sou iniciante no universo Linux e gostaria da ajuda desta
comunidade para resolver um problema: recentemente comprei um modem Yiso
C893 da Vivo Zap e segui os paços descritos no manual da Luxicom para
instalação, porém não consegui instala-lo num notebook da Acer modelo
Aspire 5100 com processador AMD Turion X2 64bits.
debian:~# lspci
00:00.0 Host bridge: ATI Technologies Inc RS480 Host Bridge (rev 10)
00:01.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge
00:04.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge
00:05.0 PCI bridge: ATI Technologies Inc Unknown device 5a37
00:13.0 USB Controller: ATI Technologies Inc IXP SB400 USB Host
Controller (rev 80)
00:13.1 USB Controller: ATI Technologies Inc IXP SB400 USB Host
Controller (rev 80)
00:13.2 USB Controller: ATI Technologies Inc IXP SB400 USB2 Host
Controller (rev 80)
00:14.0 SMBus: ATI Technologies Inc IXP SB400 SMBus Controller (rev 83)
00:14.1 IDE interface: ATI Technologies Inc Standard Dual Channel PCI
IDE Controller ATI (rev 80)
00:14.2 Audio device: ATI Technologies Inc SB450 HDA Audio (rev 01)
00:14.3 ISA bridge: ATI Technologies Inc IXP SB400 PCI-ISA Bridge (rev 80)
00:14.4 PCI bridge: ATI Technologies Inc IXP SB400 PCI-PCI Bridge (rev 80)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Miscellaneous Control
01:05.0 VGA compatible controller: ATI Technologies Inc RS482 [Radeon
Xpress 200M]
06:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
06:02.0 Ethernet controller: Atheros Communications, Inc. AR5005G
802.11abg NIC (rev 01)
06:04.0 CardBus bridge: ENE Technology Inc CB-712/4 Cardbus Controller
(rev 10)
06:04.1 FLASH memory: ENE Technology Inc ENE PCI Memory Stick Card
Reader Controller (rev 01)
06:04.2 Generic system peripheral [0805]: ENE Technology Inc ENE PCI
Secure Digital Card Reader Controller (rev 01)
06:04.3 FLASH memory: ENE Technology Inc FLASH memory: ENE Technology
Inc: (rev 01)
06:04.4 FLASH memory: ENE Technology Inc Unknown device 0551 (rev 01)
07:00.0 USB Controller: NEC Corporation USB (rev 43)
07:00.1 USB Controller: NEC Corporation USB (rev 43)
Quando faço como abaixo e conecto o modem no slot pcmcia o LED do modem
fica piscando.
debian:~# insmod
/lib/modules/2.6.18-4-amd64/kernel/drivers/usb/serial/usbserial.ko
vendor=0x0eab product=0xc893
debian:~# ls /dev/ttyUSB*
/dev/ttyUSB0 /dev/ttyUSB1
Depois disto, configuro o Gnomeppp e Kppp, mas o modem não conecta.
O que faço a partir daqui??? Não sei mais o que fazer, pois no manual é
solicitada a criação de um diretório dentro de /etc/rc.d e essa pasta
não existe no Etch.
Reply to: