Como foi pedido por alguns estou incluindo o log gerado pelo xcdroast.
Será que agora é possível encontrar o erro?
desde já obrigado.
Calling: /usr/lib/xcdroast/bin/xcdrwrap CDRECORD dev= "ATAPI:0,0,0"
gracetime=2 fs=4096k -v driveropts=burnfree speed=32 -dao -eject -pad
-waiti tsize=220045s -
scsidev: 'ATAPI:0,0,0'
devname: 'ATAPI'
scsibus: 0 target: 0 lun: 0
Warning: Using ATA Packet interface.
Warning: The related Linux kernel interface code seems to be unmaintained.
Warning: There is absolutely NO DMA, operations thus are slow.
SCSI buffer size: 64512
Cdrecord-Clone 2.01a34 (i686-pc-linux-gnu) Copyright (C) 1995-2004 Jörg
Schilling
NOTE: this version of cdrecord is an inofficial (modified) release of
cdrecord
and thus may have bugs that are not present in the original version.
Please send bug reports and support requests to
<cdrtools@packages.debian.org>.
The original author should not be bothered with problems of this version.
TOC Type: 1 = CD-ROM
Waiting for data on stdin...
Using libscg version 'schily-0.8'.
Driveropts: 'burnfree'
atapi: 1
Device type : Removable CD-ROM
Version : 0
Response Format: 2
Capabilities :
Vendor_info : 'HL-DT-ST'
Identifikation : 'CD-RW GCE-8320B '
Revision : '1.04'
Device seems to be: Generic mmc CD-RW.
Current: 0x000A
Profile: 0x000A (current)
Profile: 0x0009
Profile: 0x0008
Profile: 0x0002 (current)
Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr).
Driver flags : MMC-2 SWABAUDIO BURNFREE
Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R
Drive buf size : 1968736 = 1922 KB
FIFO size : 4194304 = 4096 KB
Track 01: data 429 MB padsize: 30 KB
Total size: 493 MB (48:54.13) = 220060 sectors
Lout start: 493 MB (48:56/10) = 220060 sectors
Current Secsize: 2048
ATIP info from disk:
Indicated writing power: 3
Reference speed: 6
Is not unrestricted
Is erasable
Disk sub type: High speed Rewritable (CAV) media (1)
ATIP start of lead in: -11596 (97:27/29)
ATIP start of lead out: 359849 (79:59/74)
1T speed low: 4 1T speed high: 10
2T speed low: 4 2T speed high: 0 (reserved val 8)
power mult factor: 2 5
recommended erase/write power: 4
A1 values: 24 2A C8
A2 values: 28 84 48
Disk type: Phase change
Manuf. index: 20
Manufacturer: Princo Corporation
Blocks total: 359849 Blocks current: 359849 Blocks remaining: 139789
Starting to write CD/DVD at speed 10 in real SAO mode for single session.
Waiting for reader process to fill input buffer ...
input buffer ready.
BURN-Free is OFF.
Turning BURN-Free on
Performing OPC...
Sending CUE sheet...
cdrecord: WARNING: Drive returns wrong startsec (0) using -150
Writing pregap for track 1 at -150
Starting new track at sector: 0
cdrecord: Input/output error. write_g1: scsi sendcmd: no error
CDB: 2A 00 00 00 02 6C 00 00 1F 00
status: 0x0 (GOOD STATUS)
cmd finished after 10.056s timeout 200s
cdrecord: A write error occured.
cdrecord: Please properly read the error message above.
write track data: error after 1269760 bytes
Writing time: 26.115s
Average write speed 181.0x.
Fixating...
Fixating time: 0.001s
BURN-Free was never needed.
cdrecord: fifo had 84 puts and 21 gets.
cdrecord: fifo was 0 times empty and 2 times full, min fill was 78%.
Jupercio Juliano wrote:
Helder Pereira Cristo wrote:
Tentei gravar em cd's regraváveis em mais de um programa (k3b e
XcdRoast) e nos dois encontrei problemas. A gravação é interrompida
logo no início. As mensagens de erro não esclarecem muita coisa.
Com cd's graváveis não tenho problemas.
Alguém poderia dar uma idéia por onde posso começar?
Bom, desisti de gravar cds regraváveis em formato udf ou outro FS
que possa ser entendido como mídia gravável ao se colocar no drive de
cd, para fazer tarefas de arrastar e soltar por exemplo.
Vejo que há incompatibilidade entre os software, pelo menos no
mundo proprietário, se gravo udf no nero, o easy cd creatror não
reconhece e vice-versa.
Faço o quê então, gravo com iso9660, assim abro em qualquer micro.
Sugiro o mesmo.
Mas um palpite sobre o seu cdrw, será que o k3b/xcd não estão
pedindo pelo sistema de arquivos udf e com suporte a escrita?
Talvez os módulos não tenham sido carregados.
Como disseram, mande as mensagens de erro.
abraços.
--
To UNSUBSCRIBE, email to debian-user-portuguese-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org