Re: cd regravável
VOcê está usando emulaçao-scsi?!
Miguel D.
On Wed, 01 Dec 2004 12:57:05 -0200
Helder Pereira Cristo <helderpc@uaivip.com.br> wrote:
> Como foi pedido por alguns estou incluindo o log gerado pelo xcdroast.
> Será que agora é possível encontrar o erro?
> desde já obrigado.
>
>
> Calling: /usr/lib/xcdroast/bin/xcdrwrap CDRECORD dev= "ATAPI:0,0,0"
> gracetime=2 fs=4096k -v driveropts=burnfree speed=32 -dao -eject -pad
> -waiti tsize=220045s -
>
> scsidev: 'ATAPI:0,0,0'
> devname: 'ATAPI'
> scsibus: 0 target: 0 lun: 0
> Warning: Using ATA Packet interface.
> Warning: The related Linux kernel interface code seems to be unmaintained.
> Warning: There is absolutely NO DMA, operations thus are slow.
> SCSI buffer size: 64512
> Cdrecord-Clone 2.01a34 (i686-pc-linux-gnu) Copyright (C) 1995-2004 Jörg
> Schilling
> NOTE: this version of cdrecord is an inofficial (modified) release of
> cdrecord
> and thus may have bugs that are not present in the original version.
> Please send bug reports and support requests to
> <cdrtools@packages.debian.org>.
> The original author should not be bothered with problems of this version.
>
> TOC Type: 1 = CD-ROM
> Waiting for data on stdin...
> Using libscg version 'schily-0.8'.
> Driveropts: 'burnfree'
> atapi: 1
> Device type : Removable CD-ROM
> Version : 0
> Response Format: 2
> Capabilities :
> Vendor_info : 'HL-DT-ST'
> Identifikation : 'CD-RW GCE-8320B '
> Revision : '1.04'
> Device seems to be: Generic mmc CD-RW.
> Current: 0x000A
> Profile: 0x000A (current)
> Profile: 0x0009
> Profile: 0x0008
> Profile: 0x0002 (current)
> Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr).
> Driver flags : MMC-2 SWABAUDIO BURNFREE
> Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R
> Drive buf size : 1968736 = 1922 KB
> FIFO size : 4194304 = 4096 KB
> Track 01: data 429 MB padsize: 30 KB
> Total size: 493 MB (48:54.13) = 220060 sectors
> Lout start: 493 MB (48:56/10) = 220060 sectors
> Current Secsize: 2048
> ATIP info from disk:
> Indicated writing power: 3
> Reference speed: 6
> Is not unrestricted
> Is erasable
> Disk sub type: High speed Rewritable (CAV) media (1)
> ATIP start of lead in: -11596 (97:27/29)
> ATIP start of lead out: 359849 (79:59/74)
> 1T speed low: 4 1T speed high: 10
> 2T speed low: 4 2T speed high: 0 (reserved val 8)
> power mult factor: 2 5
> recommended erase/write power: 4
> A1 values: 24 2A C8
> A2 values: 28 84 48
> Disk type: Phase change
> Manuf. index: 20
> Manufacturer: Princo Corporation
> Blocks total: 359849 Blocks current: 359849 Blocks remaining: 139789
> Starting to write CD/DVD at speed 10 in real SAO mode for single session.
> Waiting for reader process to fill input buffer ...
> input buffer ready.
> BURN-Free is OFF.
> Turning BURN-Free on
> Performing OPC...
> Sending CUE sheet...
> cdrecord: WARNING: Drive returns wrong startsec (0) using -150
> Writing pregap for track 1 at -150
> Starting new track at sector: 0
> cdrecord: Input/output error. write_g1: scsi sendcmd: no error
> CDB: 2A 00 00 00 02 6C 00 00 1F 00
> status: 0x0 (GOOD STATUS)
> cmd finished after 10.056s timeout 200s
> cdrecord: A write error occured.
> cdrecord: Please properly read the error message above.
>
> write track data: error after 1269760 bytes
> Writing time: 26.115s
> Average write speed 181.0x.
> Fixating...
> Fixating time: 0.001s
> BURN-Free was never needed.
> cdrecord: fifo had 84 puts and 21 gets.
> cdrecord: fifo was 0 times empty and 2 times full, min fill was 78%.
>
>
> Jupercio Juliano wrote:
>
> > Helder Pereira Cristo wrote:
> >
> >> Tentei gravar em cd's regraváveis em mais de um programa (k3b e
> >> XcdRoast) e nos dois encontrei problemas. A gravação é interrompida
> >> logo no início. As mensagens de erro não esclarecem muita coisa.
> >>
> >> Com cd's graváveis não tenho problemas.
> >>
> >> Alguém poderia dar uma idéia por onde posso começar?
> >>
> >
> > Bom, desisti de gravar cds regraváveis em formato udf ou outro FS
> > que possa ser entendido como mídia gravável ao se colocar no drive de
> > cd, para fazer tarefas de arrastar e soltar por exemplo.
> > Vejo que há incompatibilidade entre os software, pelo menos no
> > mundo proprietário, se gravo udf no nero, o easy cd creatror não
> > reconhece e vice-versa.
> > Faço o quê então, gravo com iso9660, assim abro em qualquer micro.
> > Sugiro o mesmo.
> > Mas um palpite sobre o seu cdrw, será que o k3b/xcd não estão
> > pedindo pelo sistema de arquivos udf e com suporte a escrita?
> > Talvez os módulos não tenham sido carregados.
> > Como disseram, mande as mensagens de erro.
> >
> > abraços.
>
>
>
> --
> To UNSUBSCRIBE, email to debian-user-portuguese-REQUEST@lists.debian.org
> with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
>
>
Reply to: