Ainda com duvidas na configuracao do som da placa ASUS A7S333

["eder.listas" <eder.listas@terra.com.br>]

Olá pessoal

    Ainda não consegui configurar minha placa..

   já editei o arquivo /etc/modules incluindo a linha com o nome do módulo (cmpci), mas o problema persiste.

    vou dar mais detalhes do que está acontecendo

    quando inicio o KDE aparece a seguinte mensagem:

Mensagem:

" Sound server informational message

  Error while initializing the sound driver:
  device /dev/dsp can't be opened (No such device)

  The sound server wil continue, using the null output device "

  dei uma olha nos driver da placa e constatei que ela possui os drivers para linux, mas não consegui instalar segue o manual do driver :

    Att
    
      Eder

Audio driver for CM8338/CM8738 chips by Chen-Li Tien


HARDWARE SUPPORTED
================================================================================
C-Media CMI8338
C-Media CMI8738
On-board C-Media chips


STEPS TO BUILD DRIVER
================================================================================

  1. Backup the Config.in and Makefile in the sound driver directory (/usr/src/linux/driver/sound).
     The Configure.help provide help when you config driver in step 4, please backup the original one /usr/src/linux/Document) and copy this file.
     The cmpci is document for the driver in detail, please copy it to /usr/src/linux/Document/sound so you can refer it. Backup if  there is already one.

  2. Extract the tar file by 'tar xvzf cmpci-xx.tar.gz' in the above directory.

  3. Change directory to /usr/src/linux

    //até aqui tudo bem

    // daqui em diante eu nao entendo mais nada

  4. Config cm8338 driver by 'make menuconfig', 'make config' or
     'make xconfig' command.

  5. Please select Sound Card (CONFIG_SOUND=m) support and CMPCI driver (CONFIG_SOUND_CMPCI=m) as modules. Resident mode not tested.
     For driver option, please refer 'DRIVER PARAMETER'

  6. Compile the kernel if necessary.

  7. Compile the modules by 'make modules'.

  8. Install the modules by 'make modules_install'


INSTALL DRIVER
================================================================================

  1. Before first time to run the driver, create module dependency by 'depmod -a'

  2. To install the driver manually, enter 'modprobe cmpci'.

  3. Driver installation for various distributions:

    a. Slackware 4.0  Add the 'modprobe cmpci' command in your /etc/rc.d/rc.modules file.so you can start the driver automatically each time booting.

    b. Caldera OpenLinux 2.2 Use LISA to load the cmpci module.     

    c. RedHat 6.0 and S.u.S.E. 6.1
       Add following command in /etc/conf.modules:
       alias sound cmpci

	also visit http://www.cmedia.com.tw for installation instruction.

DRIVER PARAMETER
================================================================================

  Some functions for the cm8738 can be configured in Kernel Configuration or modules parameters. Set these parameters to 1 to enable.

mpu_io:	I/O ports base for MPU-401, 0 if disabled.
fm_io:	I/O ports base for OPL-3, 0 if disabled.
  spdif_inverse:Inverse the S/PDIF-in signal, this depends on your

CD-ROM or DVD-ROM.
  spdif_loop:   Enable S/PDIF loop, this route S/PDIF-in to S/PDIF-out directly.

speakers:     Number of speakers used. use_line_as_rear:Enable this if you want to use line-in as  rear-out. 

use_line_as_bass:Enable this if you want to use line-in as   bass-out.

modem:	You will need to set this parameter if you want to use	the HSP modem. You need install the pctel.o, the modem driver itself.
  
joystick:	Enable joystick. You will need to install Linux joystick
		driver.