IBM i lm-sensors
Witam
Czy instalował ktoś może lm-sensor na serwerze IBM Netfinty?
Niestety nie pamiętam modelu 5xxx - dwóprocesorowy PIII slot I obudowa
2U, dwa zasilacze hotswap, grafika s3 savage, ethenret AMD.
Od jakiegoś czasu wiesza się sporadycznie i podejrzewam, że winą może
być temperatura. Został szczelnie obłożony serwerami konkurencyjnych
producentów i pewnie się gryzą ;).
Zainstalowałem moduły kernela i lm-sensors.
sensors-detect wypluwa pokaźną ilość informacji kończąc sugerowaną
zawartością /etc/modules:
#----cut here----
# I2C adapter drivers
i2c-savage4
# I2C chip drivers
# no driver for Smart Battery Charger yet
# Warning: the required module smartbatt is not currently installed on
your system.
# For status of 2.6 kernel ports see
http://secure.netroedge.com/~lm78/supported.html
# If driver is built-in to the kernel, or unavailable, comment out the
following line.
smartbatt
# Warning: the required module max6650 is not currently installed on
your system.
# For status of 2.6 kernel ports see
http://secure.netroedge.com/~lm78/supported.html
# If driver is built-in to the kernel, or unavailable, comment out the
following line.
max6650
# Warning: the required module saa1064 is not currently installed on
your system.
# For status of 2.6 kernel ports see
http://secure.netroedge.com/~lm78/supported.html
# If driver is built-in to the kernel, or unavailable, comment out the
following line.
saa1064
lm92
ds1621
# Warning: the required module eeprom is not currently installed on your
system.
# For status of 2.6 kernel ports see
http://secure.netroedge.com/~lm78/supported.html
# If driver is built-in to the kernel, or unavailable, comment out the
following line.
eeprom
# Warning: the required module smbus-arp is not currently installed on
your system.
# For status of 2.6 kernel ports see
http://secure.netroedge.com/~lm78/supported.html
# If driver is built-in to the kernel, or unavailable, comment out the
following line.
smbus-arp
# Warning: the required module pca9540 is not currently installed on
your system.
# For status of 2.6 kernel ports see
http://secure.netroedge.com/~lm78/supported.html
# If driver is built-in to the kernel, or unavailable, comment out the
following line.
pca9540
#----cut here----
Załadowałem moduły - a przynajmiej ich większość, nie wszystkie moduły
są w jajcu.
ds1621 8784 0
lm78 18548 0
hwmon_vid 2656 1 lm78
i2c_isa 5056 1 lm78
lm92 10480 0
hwmon 3268 3 ds1621,lm78,lm92
i2c_savage4 3940 0
i2c_algo_bit 10056 1 i2c_savage4
i2c_dev 10080 0
i2c_piix4 9168 0
i2c_core 21920 7
ds1621,lm78,i2c_isa,lm92,i2c_algo_bit,i2c_dev,i2c_piix4
niestety polecenie sensors nadal wypluwa:
# sensors
No sensors found!
Czy o czymś jeszcze zapomniałem, co jeszcze mogę mu zrobić za wyjątkiem
odwiedzenie go z siekierą w ręku?
pozdrawiam
Reply to: